Hp 4700dn 60-02 Error
Contents |
Laserjets Hp p4015 - tray 2 clacking - giving 60.02 error If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. 60.02 error 4250 To start viewing messages, select the forum that you want to visit from the selection
60.02 Error Hp 4015
below. Results 1 to 7 of 7 Thread: Hp p4015 - tray 2 clacking - giving 60.02 error Thread Tools Show Printable Version Display 60.02 error hp laserjet 4700 Linear Mode Switch to Hybrid Mode Switch to Threaded Mode 01-11-2011,02:22 AM #1 TomOgden View Profile View Forum Posts View Blog Entries View Articles Junior Member Join Date Jan 2011 Posts 1 Hp p4015 - tray 2 clacking - giving
60.02 Error 4350
60.02 error HP P4015 - Tray 2 clacking - giving 60.02 error. Found broken Tray 2 on inspection. Replaced Tray 2 - NO Change Replaced Lifter Motor - NO Change Replaced Paper Pickup Drive Assembly - NO Change Updated Firmware to 04.110.1 - NO Change Replaced DC Controller - NO Change Any other suggestions from someone who has seen this problem and successfully solved it would be appreciated. Am I possibly missing something to do with the sensor flags? They 60.02 error hp 9050 move freely and appear to be in their correct positions and alignment, but I could be mistaken. Thanks Tom Reply With Quote 01-12-2011,11:43 AM #2 MichaelTech View Profile View Forum Posts View Blog Entries View Articles Senior Member Join Date Jul 2004 Location Simi, Ca. Posts 725 Well, a 60 error is'nt in my manual, but it may be close to a DC issue. Did you do a few NVRAm Init's to sync up the formatter and DC? With all you replaced and it still clacks, could be just a toner gone bad. Is the MP trying to pick up too? It may be the issue. Reply With Quote 01-12-2011,02:25 PM #3 redcow View Profile View Forum Posts View Blog Entries View Articles Senior Member Join Date Jan 2005 Location Elk Grove, California Posts 1,097 60.02 = an error occurred while the printer was attempting to lift the tray designated by XX. You have done everything that the service manual says to do and more. Is the tray actually lifting? I'll hand this one off to Big Al Reply With Quote 01-13-2011,10:43 AM #4 Big Al View Profile View Forum Posts View Blog Entries View Articles Senior Member Join Date Apr 2008 Location Winchester Virginia Posts 520 I'm going way out on a limb here. Sometimes we get machines that someone tried to overload the tray with too much paper then slammed it back in the print
MAKING A GRINDING NOISE WHEN PRINTING Q: I have an hp laserjet 4250 making a grinding noise when it prints. The printer as far as I can tell seems to be functioning fine, in the sense that
Hp 4250 Lifter Motor
there are no reoccurring paper jams or image defects. When we look closer at
Hp P4015 Printer 60.02 Error
the machine it seems like the noise is coming from the rear of the printer. I cant really see anything from that rm1-1750 angle, but am afraid to pull it apart for fear of not putting it back together properly. Any ideas A: HP laserjet 4250 grinding noise is a very common problem with these printers. Mostly it stems http://printertechsforum.com/forum/showthread.php?3476-Hp-p4015-tray-2-clacking-giving-60-02-error from the hp 4250 fuser assembly and the 4250 swing plate assembly not properly engaging each other due to worn down gears. When the gears become worn they will not properly align and you will start to hear the grinding noises that you are describing. This is a problem that if not addressed will result in paper jams and an ultimate shutting down of the 4250 printer. Replacing the hp laserjet 4250 https://www.laserzone123.com/4250-error-codes.html swing plate assembly and the hp laser 4250 fuser assembly will resolve your grinding noise while printer issue HP LASERJET 4250 PERFORM PRINTER MAINTENANCE MESSAGE Q: I have an hp laserjet 4250 perform printer maintenance message on the display panel of my printer. The printer has yet to stop running but I am concerned that something bad will happen if I keep printing on it. Do you have any suggestions as to why this perform printer maintenance message has popped up and is there anything that I can do to clear this message? A: When your hp laserjet 4250 perform printer maintenance message appears on your display panel it is time to install a hp laserjet 4250 maintenance kit (q5421a). The printer is programmed to display that message after 200,000 pages have been printed out of the printer. The rollers and fuser assembly are rated for 200,000 prints give or take depending on operating environment and media. Much like any other consumable part, after a certain amount of use they are required to be replaced. Purchasing a maintenance kit and installing will get your HP laserjet 4250 running as it should. HP LASERJET 4250 ERROR 60.02 Q: I have an hp laserjet 4250 error 60.02 that wont seem to go away. What causes this
to allow us toaccurately quote for your repair Start again Your Postcode Get your price Get your price Call 0800 http://www.hpprinterrepair.co.uk/hp-colour-printer-repairs-service/laserjet-4700-problems/ 0186 222 quoting the reference numberbelow or complete the form to request a quote or make a booking. Get in touch with us HP Colour LaserJet 4700 (Q7491A) Printer Repair & Maintenance If your HP Colour LaserJet 4700 printer has a jam or a problem or is showing an HP error code, then our local HP printer engineers are here to help 60.02 error you. They’re experts in HP Colour LaserJet 4700 printers repair and maintenance and on hand to help with any HP Colour LaserJet printer issues. If you’re unsure how to fix your HP Colour LaserJet 4700, then get in touch; we’ll get you printing again in no time.Our HP Colour LaserJet 4700 repairs prices are fixed plus parts, so you’ll always know what 60.02 error hp you need to pay; helping you make the decision whether it’s more cost effective to repair your 4700, or replace it. Or if you need year-round support, you can choose our all-inclusive HP Colour LaserJet 4700 annual maintenance agreement.
Common HP Colour LaserJet 4700 (Q7491A) Error Codes & Problems HP Error Code:12 - Open or No EP Explanation:If you printer does have toner cartridges installed correctly, this means either a cover is open or you may have defective cooling fans or PS5 sensors. What to do:Check the all toners are installed correctly and that all covers are closed properly. If the problem persists you may have a hardware problem. HP Error Code:14 - No EP Cartridge Explanation:Your printer either doesn't have a toner cartridge installed or doesn't recognise one that is. What to do:Removing and reinstalling the toner cartridge normally resolves the problem. HP Error Code:16 - Toner Low Explanation:This normally means that your toner cartridge is either low on toner or empty. However it may mean that the remaining printer toner isn't distributed evenly. What to do:Try removing the toner cartridge and gently shabe down. Please try the request again. Your cache administrator is webmaster. Generated Mon, 17 Oct 2016 21:37:32 GMT by s_ac15 (squid/3.5.20)