Brother 2140 Drum Error Light Flashing
Contents |
toner , i still get the drum / error message still ???2. i also clean the cornora wire , using the green tab 3. someone mention the
Brother Hl-2140 Reset
toner level senor port , where is this located ??4. every other page brother hl 2170w drum error light flashing is a paper jammedplease leave message at either place: [emailprotected] -- or [emailprotected]THANKS AGAIN FOR YOUR TIME / HELP Respond brother hl 2140 all lights flashing to this 0 The drum/error is a drum error not sure why you would think the toner cartridge would fix the issue. I dont have one of those around but usually the corona wire http://support.brother.com/g/b/faqend.aspx?c=us&lang=en&prod=hl2140_all&faqid=faq00000170_017 cleaner is blue. I dont really like them becuase they dont do a good job. I usually use a damp Q-tip and alcohol. The toner level sensor port is on the right side of where the toner sits in the machine. For the error you described however you would need to check and clean the contacts for the drum on the left side of the inside of the http://www.fixyourownprinter.com/posts/63546 machine. by nivek on Aug 24, 2009 at 7:09pm Add comment Please sign in to comment 0 but if it's a drum life error then you either need to replace it and/or reset the counter.to reset the drum counter, open the fron cover, hold down the start button until all lights lit up. then release the button and shut the front cover. by tk55 on Aug 24, 2009 at 9:17pm Add comment Please sign in to comment I tried TK55's steps and it didn't work for me. Then I tried a variation and it did work. Here's what I did:(Essentially the cartridge/drum unit should not be in the printer when you reset it)1) Open front door2) Remove the cartridge/drum unit3) Hold down front button until all lights come on4) Put cartridge/drum unit back in5) Close the front doorThe Drum life should be reset.Hope this helps - unknown hello i just had this printer for 2 months , it first came with an factory toner which yield an 1,000 copies. I just bought a new generic toner, but still the same problemas for resetting the drum counter , i try that , it's doesn't work. PSS - I FORGOT TO MENTION TH
by a Fortune 500 verification firm. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate http://www.justanswer.com/printers/52b5u-red-error-light-flashing-brother-hl-2140-printer-i.html the answer you receive. Ask Sandeep Pamarati Your Own Question Sandeep Pamarati, Engineer Category: Printers Satisfied Customers: 1660 Experience: Bachelors in Electronics and Proficient in troubleshooting Computer and Printer-related problems 383181 Type Your Printers Question Here... http://www.fixya.com/support/t1040446-hl_2140_error_light_flashing Sandeep Pamarati is online now I have a red error light flashing on my Brother HL-2140 printer. I This answer was rated: ★ ★ ★ ★ ★ I have a red error light flashing brother hl on my Brother HL-2140 printer.I replaced the toner cartridge with a TN-2110 on Friday May 27th and did a small amount of printing.When I switched the HL-2140 on this morning the red error light was flashing and, of course, the printer refused to work.Assuming that perhaps the fault was connected to the replaced toner cartridge I have been trying to remove the cartridge and drum hoping that re-installation of these error light flashing units would clear the fault but I have been unable to remove the cartridge and drum from the machine. I have been trying to remove the units with the machine switched on in accordance with the toner cartridge replaceent instructions. Share this conversation Expert: Sandeep Pamarati replied5 years ago. Sandeep Pamarati : Hello Sir/maam,Sandeep Pamarati : happy to help youSandeep Pamarati : Please follow the below stepsSandeep Pamarati : Do NOT use any type of spray to clean the inside or outside of the machine. Doing this may cause a fire or electrical shock. Open the front cover. Slowly but firmly pull the drum unit and toner cartridge assembly out of the machine.Caution We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner. To prevent damage to the printer from static electricity, DO NOT touch the electrodes shown in the illustration. Clean the primary corona wire inside the drum unit by gently sliding the green tab from right to left and left to right several times.CautionBe sure to return the tab to the home position (1). If you do not, printed pages may have a vertical stripe. Put the drum un
CopiersBrotherHLHL-2040 Laser PrinterHl 2140 error light... Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Question about Brother HL-2040 Laser Printer 9 Answers Hl 2140 error light is flashing Error light is flashing Posted by wa47ma on Sep 14, 2008 Want Answer 0 Clicking this will make more experts see the question and we will remind you when it gets answered. 5 Comments Flag More Print this page Share this page × Moderate Help this question get an answer Is this question mis-categorized or about a different product? Help this question get an answer by entering the correct category or product below. Did you mean? Yes No Cancel Update (+2 points) 3 more comments emilyelle Oct 29, 2008 I have the same problem, and nothing will make the light go off. There is no paper jam. Both covers are closed. I have held the Go button down and that doesn't help. The printer will not print anything. I have the same problem, and nothing will make the light go off. There is no paper jam. Both covers are closed. I have held the Go button down and that doesn't help. The printer will not print anything. postal dude Dec 22, 2008 Same exact thing here. Flashing red "error" light, nothing in memory, doors all closed, even uninstalled and reinstalled Same exact thing here. Flashing red "error" light, nothing in memory, doors all closed, even uninstalled and reinstalled jimbomojo Apr 02, 2009 same exact problem. no paper jam. memory is not full. cover is closed, etc. I have checked everything but can't get the error light to stop flashing. very frustrating. same exact problem. no paper jam. memory is not full. cover is closed, etc. I have checked everything but can't get the error light to stop flashing. very frustrating. LaDancerly Jul 05, 2014 Exact problem. And I thought I had checked everything, but it was indeed a paper jam caused by a tiny rip of paper 1cm x 50mm must have torn of a sheet at some stage. I finally found it took it out and put the toner