Fuser Error Brother Mfc 8460n
Contents |
Copier and Fax Repair 260-417-4807 Brother Tech ArticlesCanon Tech ArticlesCopyStar Tech ArticlesDell Tech ArticlesHP Tech ArticlesKyocera Tech ArticlesLexmark Tech ArticlesOkidata Tech ArticlesSamsung Tech ArticlesXerox Phaser Tech Articles Replace Fuser Message and Reset - Brother MFC 8460, 8860,
Brother Mfc 8460n Fuser Reset
8870, DCP8060 Brother Tech Articles Add commentsFeb 122012 Replace Fuser Message and Reset - brother mfc 8860dn fuser replacement Brother MFC 8460, 8860, 8870, DCP 8060, 8065I see a lot of people looking for the instruction on the replace fuser message
Brother Mfc-8460n Fuser Replacement
and reset procedure for the Brother MFC 8460, 8860, 8870, DCP 8060, 8065. Unlike HP machines were you usually have to just pull a cover off and unclip the fuser. These machines take a little bit more brother mfc-8710dw fuser reset time and effort to replace the parts. Hopefully, after reading through this article you will have a better understanding of why the fuser needs replaced at this time and how to go about replacing it and resetting the replace fuser message.Brother Fuser Assembly LU1390001K-The replace fuser message comes up when the machine has reached 100,000 copies or prints. The good thing is the machine doesn't actually stop working but the message can get brother mfc 8910dw fuser reset annoying like the change drum soon message when you go up to use the machine and your constantly confronted with the replace fuser message. Most people want the quick fix and just want to reset the replace fuser message. Unfortunately, that is not how to properly handle the message. Once the replace fuser message is displayed on the control panel the fusing assembly needs to be replaced. Every Brother machine I've serviced for this error the fusing unit was worn out or already having print quality issues as a result of the fusing unit rollers breaking down. So I strongly recommend not ignoring the message and ordering in a fuser unit for replacement.Fuser Removal for the Brother MFC Replace Fuser Message and Reset - Brother MFC 8460, 8860, 8870, DCP 8060, 8065Back Cover 1. Open Back Cover. 2. Remove the arm of the back cover from the pin. 3. Remove the back cover.Outer Chute Assembly 1. Hold the knobs on the rear chute assembly and pull down this to your side. 2. Remove the arms of the rear chute assembly from the pins. 3. Remove the rear chute assembly.Brother Fuser LU0214001K for the MFC-8060, 8065, 8460, 8660, and 8860 Removal 1. On the left side is 1 screw on the top left corner. Remove the screw and remove the
Printer Roll Out 20 New MFP roll out. New Server Builds Built two new storage servers for 100+ PC user company. XP Machine Replacement Have 29 XP computers that need to be upgraded. TECHNOLOGY IN THIS DISCUSSION Join the Community! Creating your account only takes
Brother Hl 2270dw Fuser Error
a few minutes. Join Now I have a Brother MFC-8660DN and just replaced the Fuser. First time replace fuser unit brother mfc-8480dn coming across this and can't figure out the reset code to reset life counter on the fuser. Anybody know the procedure? Thanks! Reply Subscribe RELATED TOPICS:
Brother Mfc 8660dn Fuser Replace
Brother MFC-L9550CDW Reset Menu Brother MFC-9440CN Issue brother mfc 8220 factory reset   9 Replies Serrano OP TonyB9287 Feb 23, 2012 at 5:01 UTC Hello There, You can attempt to use the following below, we have Brother MFC-8890DW in our http://www.fortwayneprinterrepair.com/wordpress/2012/02/12/replace-fuser-message-reset-brother/ enviroment and have replaced the fuser on one so far.. Enter Maintenance menu by pressing Menu,*,2,8,6,4 8,8 for parts life scroll down to fuser hit start for yes 9,9 to exit 0 Pimiento OP reagp Feb 23, 2012 at 7:59 UTC I appreciate the reply, but already tried that and that doesn't work. Thanks again. 1 Pimiento OP reagp Mar 1, 2012 at 1:29 UTC I found the answer through a local retail printer repair shop. Turn the machine https://community.spiceworks.com/topic/201499-brother-mfc-8660dn-fuser-reset off, and then turn back on holding the "Menu" button at the same time and the "Maintenance" screen will come on the LCD. Scroll down arrow to "Fuser" and then "OK" then 99 to exit. You will likely see the "Laser" on the screen after complete this procedure, because you usually replace the laser too, but just repeat the same procedure selecting the Laser even if you are not replacing the Laser. The error message will go away and you have just reset the life counter on both. 3 Pimiento OP mike_r_edwards_9 Oct 17, 2012 at 4:55 UTC 1st Post THAT DOESN'T WORK EITHER. YOU get into maintenance mode but no clue as to which of the 99 options is fuser life 0 Pimiento OP seanhayes2 Apr 10, 2014 at 5:34 UTC 1st Post When the printer is on, hold 3 & 9.. You will get a menu... Scroll to Fuser, and select it.. then Reset... Do the same for Laser, if you've also replaced the laser. 1 Serrano OP joe mm Apr 18, 2014 at 7:08 UTC This youtube on it might be helpful. It's actually for a 8480 but it's a similar printer. http://www.youtube.com/watch?v=quGzXnDsZQA 0 Sonora OP Roy1070 Mar 22, 2016 at 5:53 UTC 1st Post This worked for a Brothers MFC-8910dw. Thanks 0 Pimiento OP alainleguillou Jun 7, 2016 at 10:11 UTC 1st Post very easy on MFC8480DN, after replacing parts, thanks 0 Pimiento OP leejohnson6 Jul 31, 201
lag and temperature drop rate Measuring Ulka EP5 Pump Inductance Recent CommentsPhil Swoffer on Renault Modus: Flashing Headlight Fault or Indicator Faultjames on Renault Modus: Flashing Headlight Fault or Indicator FaultPhil Swoffer on Renault Modus: Flashing Headlight Fault or Indicator http://int03.co.uk/blog/2014/11/17/brother-mfc-8860dn-fuser-replacement/ Faultjames on Renault Modus: Flashing Headlight Fault or Indicator Faultjames on Renault Modus: Flashing Headlight Fault or Indicator FaultArchives August 2016 July 2016 June 2016 May 2016 April 2016 February 2016 January 2016 December 2015 November 2015 October 2015 August 2015 June 2015 March 2015 February 2015 January 2015 December 2014 November 2014 July 2014 April 2014 March 2014 February 2014 Categories Uncategorized Meta Log in Entries RSS Comments RSS WordPress.org Brother MFC-8860DN Fuser Replacement We have one brother mfc of those multi-function scanner/printer/fax/copier machines at work, the Brother MFC-8860DN. After a few years of faithful service, it started displaying "Fuser Error" and refused to print. We needed a new one fairly urgently, so I immediately bought a new HP one as replacement, but I wasn't quite ready to send the old Brother to the graveyard and decided to try replacing the Fuser. Having switched off the power, I pulled the back cover off the printer and brother mfc 8460n located the fuser unit. This wasn't too difficult to get to: there are two panels which pop out, two screws to remove, and two more covers to gain access to the connectors for the heater and sensor cables. The picture below shows the panels/covers to be removed. The Panels A and B can simply be popped out by bending one of their plastic "hinges" at either the left or right hand side. The cover C is held on by one cross-head screw, and the cover D simply pops off if you push on the spring tab (near the letter D below). Having removed cover D, you will gain access to another cross-head screw. After removing those two screws, and disconnecting four cable connectors, the Fuser can be lifted out of the printer. The Fuser is basically just a heated roller, so there are only a limited number of things that could go wrong. For example, it could be a loose connection, a burnt out heating element, or a faulty sensor. At the left hand side there are two fairly thick cables with spade connectors, and the cover has a temperature warning sticker. It seemed fair to assume these were the heater terminals… Having pulled off the two spade connectors, I measured the resistance and they were open circuit. Concluding that the heating element had burnt out, I ordered a new F