Mp258 Canon Error Code List
Contents |
allUploadSign inJoinBooksAudiobooksComicsSheet MusicCanon Pixma Mp258 Error Code and Possible SolutionUploaded by Maizatul Nabillah6.1K viewsDownloadEmbedSee MoreCopyright: Attribution Non-Commercial (BY-NC)Download as DOCX, PDF, TXT or read online from ScribdFlag for inappropriate content Canon Pixma Mp258 Error Code and Possible Solution P02 (Carriage error) 1. Make sure no foreign material stuck to canon printer mp258 error code list the print head railway. 2. Clean and check the print head encoder strip cable
Canon Mp258 Error E03
(timing slit film or encoder strip is a whiteline on the back of the box set of ink lines may be missing
Canon Mp258 Reset
or mess up the ink. P03 (Line feed error) : an error in transmission line entering the line feed (LF) is asignal telling the printer to move to another line or a whole new line that
Canon Mp258 Error E05
would not otherwise havereached the end of the line. 1. Check wire print head position (timing slit disk film) on the side of the machine. 2. Check PCB logic board. P05 (ASF sensor error) sensor for paper feed error. 1. Try to replace the following: y ASF / PE sensor unit. y Drive unit. y PCB logic board. P06 (Internal temperature error): caused by abnormal heat inside canon mp258 error p02 theprinter. P07 (Ink absorber full): the Ink Wastepad (sponge) inside the printer is full 1. Replace the wastepad inside the printer or install waste ink bin outside the printer 2. then Reset counter protection. P08 (Print head temperature rise error): caused by thermal print headtemperature exceeds a threshold. 1. Replace the new cartridge print head and / or change a new logic board. P09 (EEPROM error): caused by corrupted or defective EEPROM chips of the printer. 1. Replace the logic board. P15 (USB VBUS over current): caused by too much current, try removing theUSB cable and then plugin again, if solve the error, try to replace with a new USB cable. If the error still exist replace the logic board. P20 (Other hardware error): The failure of other hardware. 1. Try to replace the logic board. P22 (Scanner error): a scanner malfunction. 1. try to change the scanner unit or change a the logic board. E13 or E16: Ink has run out 1. Pressing the Stop / Reset button for 5 to 8 seconds until the led screen display number 1. E04, E05, E14 or E15: Cartridge may not be installed properly 1. Reinstall the ink cartridge. 2.Error Code Printer Cano
/ error codes for the MP250 and MP270. Solution An Error Code Is Displayed on the LED Issue Alarm Lamp Is Lit Orange When a machine error occurs, the Alarm lamp canon mp258 error e05 fix is lit orange and E and number (error code) are alternately displayed on the e04 canon mp258 LED. Check the error code displayed on the LED and take the appropriate action to correct the error. * Depending canon mp250 error codes on the error occurred, the Alarm lamp is not lit. Power Lamp Flashes Green and Alarm Lamp Flashes Orange Alternately When the Power and Alarm lamps flash alternately as shown below, and P https://www.scribd.com/doc/77544379/Canon-Pixma-Mp258-Error-Code-and-Possible-Solution and number (error code) are alternately displayed on the LED, an error requiring servicing might have occurred. LED Displays E, 0, 2 The machine is out of paper / Paper does not feed Summary Reload the paper on the Rear Tray correctly and also check for and remove any jammed paper or foreign object. Press the Black or Color button. LED Displays E, 0, https://support.usa.canon.com/kb/index%3Fpage%3Dcontent%26id%3DART133186 3 Paper Output Tray is closed / Paper jam Summary If the Paper Output Tray is closed, open it. The machine resumes printing. If opening the Paper Output Tray does not resolve the problem, or if the tray was open to begin with, the paper may be jammed. Remove the jammed paper, reload paper properly in the printer, then press the Black or Color button. Paper Jams LED Displays E, 0, 4 / E, 0, 5 The FINE Cartridge cannot be recognized Summary The FINE Cartridge may not be installed properly, or the Cartridge may not be compatible with this machine. Open the Scanning Unit (Cover) and install the appropriate FINE Cartridge. Installing / Replacing FINE Cartridge(s) If the error is not resolved, contact the service center. PIXMA MP250 PIXMA MP270 LED Displays E, 0, 7 FINE Cartridge is not installed in the correct position Summary Make sure that each FINE Cartridge is installed in the correct position. Installing / Replacing FINE Cartridge(s) LED Displays E, 0, 8 Ink absorber is almost full Summary Press the machine's Black or Color button to continue printing. Contact the service center. PIXMA MP250 PIXMA MP2
samla information på och utanför Facebook. Läs mer, inklusive om tillgängliga kontrollfunktioner: Policy för cookiesFacebookE-post eller telefonLösenordGlömt kontot?Visa mer av Al-Hasub™ genom att logga in på FacebookSkicka meddelanden till den här sidan, få information om kommande https://www.facebook.com/NajibTrading/posts/335955993138714 evenemang och mycket mer. Om du inte har något Facebook-konto kan du skapa ett för att se mer från den här sidan.Gå medLogga inVisa mer av Al-Hasub™ genom att logga in på FacebookSkicka meddelanden http://vanjavaboy.blogspot.com/2011/02/canon-mp258-error-code-and-how-to-fix.html till den här sidan, få information om kommande evenemang och mycket mer. Om du inte har något Facebook-konto kan du skapa ett för att se mer från den här sidan.Gå medLogga inInte nuNyheterAl-Hasub™den 12 canon mp258 maj 2012 · ™ CANON PIXMA MP258 ERROR CODE LIST E02 – Printer is out of paper Insert some papers and press start button ( black or green button) E03 – Paper jam or Paper output tray is closed There are two reason, either paper jammed or the paper output tray is closed, the first step is to check the paper tray output, make sure to open it canon mp258 error and insert some paper before begin printing. The second reason is the paper may jammed, start with removing the jammed paper, press start button (green or black button) to reload the paper. E04 / E05 – The printer cartridge cannot be recognized These error codes happen because the printer cannot recognize the ink cartridge. It could be the current ink cartridge is incompatible with the printer. Open the printer cover and reinstall the ink cartridges. If these error codes still appear, please contact the canon service center. E07 – The printer cartridge is not installed correctly Please check the printer cartridge installed properly, open the printer cover and reinstall the ink cartridges. If these error codes still appear, please contact the canon service center. E08 – Ink absorber is almost full The ink absorber is about to full, it’s time for you to replace the ink absorber. Bring your printer to service center. You still able to use this printer even the printer warned you the ink absorber is full. Press start button (black or green button) to continue using the printer. E13 – The printer ink level cannot be detected This error code appear when the printer detected a low ink, som
Error code and fix: MP258 Error code there are 2 types of codes, namely: 1. that uses the letters before P, for example P07 2. that uses the letters before E, eg E05 P Canon MP258 Error code: P02 (Carriage error) Solution: 1. Make sure no foreign object stuck in the roll printer. 2. Clean and check the encoder, may be exposed to splashes of ink. P03 (Line feed error) Cause: Timing Disk dirty / damaged. Solution: 1. Check the timing disk sensor located to the left of the printer 2. Check and clean the board. P05 (ASF sensor error) Cause: The paper detection sensor Canon MP258 Error. Solution: Try changing one of the following parts: • ASF / PE sensor unit. • Motor. • Board Printer Canon MP258. P06 (Internal temperature error): Cause: Excessive heat in the Canon MP258 printer. Solution: 1. Clean the inside of the MP258 printer. 2. replace Board MP258 Printer P07 (Ink absorber full): Cause: Full Counter Ink, Printer Canon MP258 already saaenya on reset. Solution: Reset Printer Canon MP258 using software P08 (Print head temperature rise error): Cause: Head too hot, exceeds the threshold, usually the color Catridge Solution: Try changing the color catrid Canon MP258 printer. P09 (EEPROM error) Cause: Canon MP258 experienced board EEPROM Corrupt or damaged. Solution: 1. Board replace Canon MP258 printer. P15 (USB VBUS over current) Cause: The printer excess current from the USB cable Canon MP258 printer. Solution: 1. Try to Change Printer Canon MP258 USB cable. 2. If still defective, replace the Board Printer Canon MP258. P20 (Other hardware error) Cause: damage to other hardware Solution: Board replace Canon MP258 printer. P22 (Scanner error) Cause: The scanner is not working Solution: 1. Replace Canon MP258 printer scanner. 2. Board Replace Canon MP258 printer. Canon MP258 Error code E: E04: Catridge Canon MP258 is not installed properly. Solution: Take the catridge and then put it again E05: Catridge Canon MP258 is not installed properly or there is one damaged catrid Solution: 1. Take the cartridge, then plug it in again 2. Replace the cartridge if there is a distinguished damaged E14 and E15: Catridge Canon MP258 is not installed properly. Solution: Take the catridge and then put it again E13 and E16: Ink has run out / cartridge must be reset. Solution: Press the STOP / Reset for 5 - 15 seconds wait until the led display process. Hopefully useful ... Posted by Teen Virgin Education at 3:40 PM Email ThisBlogThis!Share to TwitterShare to FacebookShare to Pintere