Ceer Error 50
Contents |
July 31, 2014 - 2:00pm, 1315 views Modules Hi, We have a Windows CE 7 device that has EHS5-E device. ASC0 and USB are connected, but we don't have USB drivers yet. We can communicate via ASC0 using a terminal. When we +cme error: 100 try establish a RAS connection (dial-up), it dials but after ~20 seconds we get RAS
Cms Error
error 679 ("Cannot detect carrier."). When we dial using terminal ("ATDT *99***1#") we get "CONNECT", then some content and then "NO CARRIER". That cms error 50 is similar as with dial-up. We have tested that - signal is ok (+CSQ: 13,99) - modem is attached to network - SIM is fine Any ideas? Regards, Janne Like010Comment Log in or register to post comments
Cme Error 50
MichaĆ - Gemalt... Jul 31 2014 - 4:59pmHi Janne, Please let us know if you are using RIL driver. Do you have any logs? Walking on water and developing software from a specification are easy - if both are frozen. Like0 Log in or register to post comments jannenivala Aug 1 2014 - 12:42pmHi, We're not using a RIL driver. I'll post RAS dialer console output asap. I'm not aware of any other log available for sms error code 69 us. Is there something that I can get from modem or OS that you are aware of? Edit: Microsoft RIL driver is loaded but RIL driver configuration does not point to correct serial port. There is no Cinterion USB driver for modem. => RIL does not interact with the modem and thus does not contribute to this case. When modem is started we get a notification of a new USB device without a driver. Regards, Janne Like0 Log in or register to post comments jannenivala Aug 1 2014 - 12:22pmThis is what is printed to CE device debug port: AUTORAS:: Dialer notifies: [1] [Dialer Start] RASCS_Disconnected: Ecode=679 Posting WM_NETCONNECT(FALSE) message, ErrorCode = 679(0x2A7) AUTORAS:: Dialer notifies: [2] [Dialer Terminate] Like0 Log in or register to post comments jannenivala Aug 4 2014 - 7:50pmAT+CEER outputs: +CEER: "CC setup error",50,"Requested facility not subscribed" Could that have anything to do with this? Like0 Log in or register to post comments jannenivala Aug 4 2014 - 7:54pmWe have a DSB75 evaluation board with EHS5-E attached, too. When trying to connect from PC terminal using AT commands, we get the same result as with the CE device (CONNECT... content... NO CARRIER). When we setup a dial-up connection in Windows 8, we get "Connection failed with error 651". RAS error 651 is "Your modem (or other connecting device) has reported an erro
post a blank message. Please type your message and try again. Jessica517 Level 1 (7 points) Q: Unknown Error Message -50? I keep getting a
Cms Error 304
message when I sync my ipod touch saying "Itunes could not copy
Cms Error 21
"name of the song" to the ipod "name of ipod" because an unknown error occurred (-50)" Plus cms error codes not all my songs are syncing only partially. I have tried alot of things and read discussions relating to this issue and I'm becoming very fustrated with situation. https://developer.gemalto.com/threads/ehs5-e-no-carrier Thank you! iPod touch, iOS 5.1.1 Posted on Aug 13, 2012 10:08 AM I have this question too Close Q: Unknown Error Message -50? All replies Helpful answers Page 1 Next by lllaass, lllaass Aug 13, 2012 10:40 AM in response to Jessica517 Level 10 (189,275 points) Desktops Aug 13, 2012 10:40 AM in response to Jessica517 Error https://discussions.apple.com/thread/4204776?tstart=0 13, 14, 35 and 50 (or -50)These errors are typically resolved by performing one or more of the steps listed below:Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.Put a USB 2.0 hub between the device and the computer.Try a different USB 30-pin dock-connector cable.Eliminate third-party security software conflicts.There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.Try to restore from another known-good computer and network.or:http://support.apple.com/kb/TS3833or:"Error -50," "-5000," "8003," "8008," or
ElementsAdobe Dreamweaver Adobe MuseAdobe Animate CCAdobe Premiere ProAdobe After EffectsAdobe IllustratorAdobe InDesignView all communitiesExplore Menu beginsMeet the expertsLearn our productsConnect with your peersError: You don't have JavaScript enabled. This tool uses JavaScript and much of it https://forums.adobe.com/thread/1432237 will not work correctly without it enabled. Please turn JavaScript back on and reload this page. Please enter a title. You can not post a blank message. Please type your message and try again. More discussions in Creative Cloud Download & Install All CommunitiesDownloading, Installing, Setting UpCreative Cloud Download & Install This discussion is locked 1 cms error 2 3 Previous Next 107 Replies Latest reply on Apr 7, 2015 3:00 PM by Jeff A Wright Branched to a new discussion. Error code 50 billgeo Mar 20, 2014 1:52 AM I followed the instructions to rename OODB folder to OODB.old. Creative Cloud disappeared from my desk top. I then went to www.adobe.com/go/applicationmanager to dowmload Creative ceer error 50 Cloud desktop manager. During the installation I got error message 50. Do I need to reload all of Creative Cloud? If so, how is the best way to do this? At the present time Iam not able to use photoshop. Please help me. 57277Views Tags: none (add) This content has been marked as final. Show 107 replies 1. Re: Error code 50 jre Mar 20, 2014 2:08 AM (in response to billgeo) I have the same problem Like Show 1 Likes(1) Actions 2. Re: Error code 50 Jeff A Wright Mar 20, 2014 7:39 AM (in response to billgeo) Billgeo, Jre, and Fabio.duarte please see Error "Failed to Install" Creative Cloud Desktop application - http://helpx.adobe.com/creative-cloud/kb/failed-install-creative-cloud-desktop.html for information on how to resolve your current error. If you continue to receive an error 50 can you please post a screen shot of the error? Like Show 1 Likes(1) Actions 3. Re: Error code 50 TheStormFury Mar 20, 2014 8:26 AM (in response to Jeff A Wright) Hey, here's an idea! W