Error 0022 After 30 Sec
Contents |
E10/0022 Bridged solder joint/Short GPU-> (H)ANA Add / Edit Details Primary Error code: 3 RLOD E-Code / Secondary Error code:E10 xbox 360 error 0022 fix (No Audio/Video) / 0022 Binary/Hex:00001010 / 0x0A -> 10 Known fixes: 1)If you
Xbox Error Code 0022 Fix
soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much 0022 code power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU. 2) X-Clamp replacement 3) Reflow GPU and HANA chip 4) If +22 it\'s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU. 5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original. 6) also can be caused by a broken trace (see link below). Related Errors:Powered by Xbox-experts.com No Related Errors available! Description: This error is caused by a bridged/shorting
+22 Country Code
solder joint under the GPU, (H)ANA-chip or in between.It can also be power related though, for example if you are drawing power from one of the regulators that power the GPU and HANA-chip.Can also be a component that is missing or damaged so look for missing parts near the GPU and the HANA chip. In extremely rare cases it might also be related to the lines that lead from HANA to the CPU. The chances are however higher that it is the GPU than the HANA chip so you should always first concentrate on the GPU. Another cause could be due to a broken trace under the board near one of the ram blocks, check the picture in the reference section. Thank you arvydas for reporting this solution! This error also show up if the CPU ! was taken off the mainboard. References: picture of broken trace (repaired) Clicks:271147 Share(BBCode): [b]Details for Error code E10/0022[/b] [b]Description:[/b] This error is caused by a bridged/shorting solder joint under the GPU, (H)ANA-chip or in between.It can also be power related though, for example if you are drawing power from one of the regulators th
replies and 984 views. xXDANTE2Xx Enthusiast Messages: 29 Ratings: 1 Jun 16, 2013 #1 Hello everyone, I have an xbox 360 with secondary code 0022, I have tried everything to 00224 country code fix it, or at least do a measly fix with a crappy heat gun. The 00221 country code problem is, its my co-workers and he handed it to me to fix. I told him I couldn't so he let
002 Country Code
me keep it, the larger problem is, the console is a JTAG able console. I really want to JTag it and give it back to him because he has let me work there for the past https://xbox-experts.com/errorcode/E10/0022/ 2 years. Info: Secondary Error Code: 0022 Boots after 30 seconds (35-36 ish) Console doesn't appear to be a JTAG Here are some of the photos Images Spoiler This is the method I use to replace the XClamps (I know I screwed up the GPU heatsink clamp thing so I cant remove it (yet) PS.(I like to spice things up a little) PPS. (This isn't were I work so don't be like nice http://www.se7ensins.com/forums/threads/xbox-360-0022.938324/ anti static environment because I had it in my room and I was lazy to setup my workstation in my basement.) xXDANTE2Xx, Jun 16, 2013 xXDANTE2Xx, Jun 16, 2013 #1 Kyllswitch And Justice for All Messages: 2,259 Ratings: 419 Jun 16, 2013 #2 You need to clean the CPU and the heatsink. Kyllswitch, Jun 16, 2013 Kyllswitch, Jun 16, 2013 #2 xMODDEDxSKILLZx Seasoned Member Messages: 3,106 Ratings: 644 Jun 16, 2013 #3 you either have a bad flash, or a potential reflow candidate. xMODDEDxSKILLZx, Jun 16, 2013 xMODDEDxSKILLZx, Jun 16, 2013 #3 Mysterion Getting There Messages: 2,269 Ratings: 943 Jun 16, 2013 #4 0022 - CPU error, generally caused by a poor connection to the mainboard (cold solder joints/bridged solder joints). This can also be triggered by an error with the TSOP. So, from that, I would reflow CPU (Cold solder joints). Mysterion, Jun 16, 2013 Mysterion, Jun 16, 2013 #4 xXDANTE2Xx Enthusiast Messages: 29 Ratings: 1 Jun 16, 2013 #5 xMODDEDxSKILLZx said: ↑ you either have a bad flash, or a potential reflow candidate.Click to expand... It doesn't look like its been JTagged though, from what I can see, So I guess I can retry a CPU reflow, I plant on buying an BGA rework station so I cant star
have done about 30 RGH Slims and Fat (25 Slims + 5 Fat). i never had problems with the Slims. only the Phats. 2 out of the 5 Fat got RROD 0022. When the Hacked image runs it keeps glithing for Ever. but when i put back the original http://www.ps3hax.net/archive/index.php/t-50359.html NANDs it gives me RROD 0022 after 30 Sec. as i have been told it is the CPU https://xboxexperts.de/errorcode/E10/0022/ fried, but why. i am sure my soldering is perfect, and never happened to me in the Slims. i am using NANDx and Coolrunner Rev.C. Any help here? not how to fix it, i know i should probebly get another CPU if yhe CPU is fried. but what cause this issue and how to prevent it? since i am thinking of not Doin RGH for the Fati Sarah1331 aka Paul (Hope it is country code right), can you help here? Sarah133101-15-2013, 06:57 AMIf your on stock NAND and fans glitch 6 times that's the smc resetting after 6 it rrod 0022 that's CPU dead When soldering make sure it is not on standby "plugged in" it's the green wire that killed it CPU bypass Sent from my iPhone 5 using Tapatalk 3absiso01-15-2013, 07:06 AMIf your on stock NAND and fans glitch 6 times that's the smc resetting after 6 it rrod 0022 that's CPU dead When soldering make sure it is not on standby "plugged in" it's error 0022 after the green wire that killed it CPU bypass Sent from my iPhone 5 using Tapatalk Let me understand it better. what is exactly the fans glitch 6 times i did not get it. and how it can be fixed if it is SMC resetting? and i never solder with the PSU on the Mobo. i am really a big n00b in the xbox360 but i am trying. Mistawes01-15-2013, 07:09 AMIt's just not getting a good glitch. I've had boxes do that before, took ages of tweaking and then performed fine after (tends to happen more on RGH2 for me, nearly always fats anyway). The ECC file stops the 0022 error from preventing boots when re-trying the glitch. Are you getting the green flashing light on your CR3? 0022 on stock is normal, with CR installed. Remove it (or switch it to program mode) and test on stock NAND and it should boot. Is the Falcon RGH2 or RGH1? 3absiso01-15-2013, 07:35 AMIt's just not getting a good glitch. I've had boxes do that before, took ages of tweaking and then performed fine after (tends to happen more on RGH2 for me, nearly always fats anyway). The ECC file stops the 0022 error from preventing boots when re-trying the glitch. Are you getting the green flashing light on your CR3? 0022 on stock is normal, with CR installed. Remove it (or switch it to program mode) and test on stock NAND and it should boot. Is the Falcon RGH2 or RGH1? The Coolrunner glitches for Ever and the green light keep pulsing each 5 seconds. I returned the Xbox to stock without the coolrun
Fehlercode E10/0022 Überbrückte/Kaltlötstelle - GPU - (H)ANA Hinzufügen / Bearbeiten Details Primärer Fehlercode: 3 RLOD E-Code / Sekundärer Fehlercode:E10 (Kein Audio/Video) / 0022 Binär/Hex:00001010 / 0x0A -> 10 Problemlösungen: 1) Wenn Sie kurz zuvor etwas an das Mainboard gelötet haben entfernen Sie es. Werden Sie ebenfalls alles los, das einen Kurzschlussverursachen könnte in der GPU-Gegend, wie Lötbrücken etc. Suchen Sie ebenfalls nach fehlenden/defekten Komponenten, wie Widerständen und Kondensatoren. 2) X-Clamp Fix Hybrid 3) GPU Reflow(und ggf HANA chip Reflow wenn dies fehlschlägt und es eine HDMI Konsole ist) 4) Wenn es nicht der GPU/(H)ANA chip ist, kann es auch der CPU sein, da hilft ein CPU Reflow. 5) Wenn man den JTAG Mod durchgeführt hat nochmal Flashen oder das Original aufflashen. Verwandte Fehler:Powered by Xbox-experts.com Kein(e) Verwandte Fehler verfügbar! Beschreibung: Dieser Fehler wird meist durch eine überbrückte Lötstelle/Kurzschluss unter/in der Nähe dem GPU/(H)ANA chip ausgelöst. Es kann ebenfalls ein Problem mit der Stromversorgung des GPU und (H)ANA chips sein. Der Grund dafür sind meist fehlende/defekte Komponenten wie MOSFETs, Widerstände, Koondensatoren etc. In sehr seltenen Fällen kann es auch an einer der paar Leitungen, die zum CPU führen liegen(möglicherweise Lötbrücke oder Kaltlötstelle unter dem CPU). Der CPU ist allerdings sehr selten das Problem man sollte sich primär auf GPU(60% Wahrscheinl.) und (H)ANA chip(40% Wahrscheinl.) konzentrieren. Referenzen: Kein(e) Referenzen verfügbar! Klicks:63920 Share(BBCode): [b]Details für Fehlercode E10/0022[/b] [b]Description:[/b] Dieser Fehler wird meist durch eine überbrückte Lötstelle/Kurzschluss unter/in der Nähe dem GPU/(H)ANA chip ausgelöst. Es kann ebenfalls ein Problem mit der Stromversorgung des GPU und (H)ANA chips sein. Der Grund dafür sind meist fehlende/defekte Komponenten wie MOSFETs, Widerstände, Koondensatoren etc. In sehr seltenen Fällen kann es auch an einer der paar Leitungen, die zum CPU führen liegen(möglicherweise Lötbrücke oder Kaltlötstelle unter dem CPU). Der CPU ist allerdings sehr selten das Problem man sollte sich primär auf GPU(60% Wahrscheinl.) und (H)ANA chip(40% Wahrscheinl.) konzentrieren. [b]Fixes:[/b] 1) Wenn Sie kurz zuvor etwas an das Mainboard gelötet haben entfernen Sie es. Werden Sie ebenfalls alles los, das einen Kurzschlussverursachen könnte in der GPU-Gegend, wie Lötbrücken etc. Suchen Sie ebenfalls nach fehlenden/defekten Komponenten, wie Widerständen und Kondensatoren. 2) [url=http://xbox-experts.com/tutorial/team-hybrids-ultima