Dameware Error 10060
Contents |
Troubleshooting Winsock 10060 Errors The information in this article applies to: DameWare Mini Remote Control Winsock Connect Error System Error:
How To Fix Error Code 10060
10060 Connection timed out. A connection attempt failed because the connected party winsock connect error system error 11004 did not properly respond after a period of time, or established connection failed because connected host has failed to winsock error 10060 the connection timed out respond. Please keep in mind that Winsock Errors are Microsoft Windows Sockets (TCP) errors, not DameWare error, and typically when a Winsock 10060 error is reported it's typically either due
Error Code 10060 Socket Connection Failed
to an improperly configured Firewall (hardware or software), a Names Resolution issue, or even improper routing within your network implementation (especially when VPNs or multiple NICs are involved). These configuration issues then cause the TCP Socket to timeout, which then causes the Winsock 10060 error to occur. Unfortunately, there are no settings within our software that would either cause, or prevent a
Socket Error 10060 Connection Timed Out Windows 7
Winsock 10060 error (or any other Winsock error) from occuring. However, here are some things you can try: First make sure that all routers & firewalls between the Local & Remote Machines, and any firewall software on the remote machine itself (i.e. Windows Firewall for SP2 or Vista, etc..) are properly configured to allow the necessary traffic to pass through. Our software is compatible with any firewall (hardware or software), but you must properly configure the firewall to allow the necessary traffic to pass through. Otherwise the connection will timeout with a Winsock 10060 error. Please see the following knowledgebase article for more information: Using DameWare Development Products in Conjunction with XP Service Pack 2 Also, if you are currently using version 6.x of the software, then after you install v6.x of the MRC Client Agent Service on the remote machine, once the Client Agent starts up it should automatically create a port exception in the Windows Firewall (under Vista or XP) for the specified TCP port used for communication (default is TCP 6129). But make note this does not open the ports re
General Network Configuration & Implementation Issues The information in this article applies to: DameWare Remote Support DameWare Mini Remote Control System errors are Microsoft Operating 10060 socket error System errors, not DameWare System errors. Likewise, Winsock errors are Microsoft Windows Sockets
Dameware Winsock Connect Error 10061
(TCP) errors. The vast majority of all Operating System errors encountered while using the DameWare NT Utilities or DameWare Mini connect error 10060 outlook Remote Control programs (i.e. System Errors, Winsock Errors, etc.) are not directly related to DameWare software. Most often, these issues are directly related to some type of system or network configuration issue within http://support.dameware.com/kb/article.aspx?ID=300060 a network environment and can usually be duplicated outside of DameWare software. The following are some examples of network configuration & implementation issues, along with some additional links that may help troubleshoot these specific issues in the environment: System Error:31 The graphic device driver supports more than one (1) planes. http://www.dameware.com/kb/article.aspx?ID=400227 System Error: 51 ERROR_REM_NOT_LIST Windows cannot find the network path. Verify that the network path is http://support.dameware.com/kb/article.aspx?ID=300005 correct and the destination computer is not busy or turned off. If Windows still cannot find the network path, contact your network administrator. http://www.dameware.com/kb/article.aspx?ID=300061 System Error: 53 ERROR_BAD_NETPATH The network path was not found. http://www.dameware.com/kb/article.aspx?ID=300059 System Error: 1300 ERROR_NOT_ALL_ASSIGNED Not all privileges or groups referenced are assigned to the caller. http://www.dameware.com/kb/article.aspx?ID=300085 System Error: 1707 RPC_S_INVALID_NET_ADDR The network address is invalid. http://www.dameware.com/kb/article.aspx?ID=300024 System Error: 1814 ERROR_RESOURCE_NAME_NOT_FOUND The specified resource name cannot be found in the image file. http://www.dameware.com/kb/article.aspx?ID=300092 Winsock Connect Error: System Error: 10050 Network is down. This error may be reported at any time if the Windows Sockets implementation detects an underlying failure. This could indicate a serious failure of the network system (that is, the protocol stack that the Windows Sockets DLL runs over), the network interface, or the local network itself. http://www.dameware.com/kb/article.aspx?ID=300058 Winsock Connect Error: System Error: 10054 An existing connection was forcibly closed by the remote host. This normally results if the peer application on the remote host is suddenly stopped, the host is rebooted, or the remote host uses a hard close (see setsockopt for more information on the SO_LINGER option on the remote socket). This error may also result if a connection was
Manager (IPAM)ipMonitorKiwi CatToolsKiwi Syslog ServerLog & Event Manager (LEM)Mobile AdminNetFlow Traffic Analyzer (NTA)Network Configuration Manager (NCM)Network Performance Monitor (NPM)Network Topology Mapper (NTM)Patch ManagerServer & Application Monitor (SAM)Serv-U FTP & MFTStorage https://thwack.solarwinds.com/thread/59125 Resource Monitor (SRM)User Device Tracker (UDT)Virtualization ManagerVoIP & Network Quality Manager (VNQM)Web Help Desk (WHD)Web Performance Monitor (WPM)Blogs & GroupsGroupsCommunity ConversationsEvents & WebcastsFederal & GovernmentFun & GeekyJob BoardSolarWinds Certified ProfessionalsSpread the WordTHWACK EMEAUser ExperienceBlogsAnnouncementsGeek SpeakProduct BlogSolarWinds User GroupsSolarWinds LabContests & MissionsThwack StoreFree Tools & Trials Log inRegisterGetting StartedSearchSearchCancelBrowseContentPeopleForums & GroupsStoreHomeNewsPeopleError: You error 10060 don't have JavaScript enabled. This tool uses JavaScript and much of it will not work correctly without it enabled. Please turn JavaScript back on and reload this page. Please enter a title. You can not post a blank message. Please type your message and try again. More discussions in DameWare MRC error code 10060 All PlacesApplication & ServerDameWare MRC 5 Replies Latest reply on Sep 11, 2013 9:29 AM by Lawrence Garvin DameWare MRC v6.1 does no longer work on client computers hoagie Sep 6, 2013 12:31 AM Good Morning,I have been using DameWare MRC for quite some years now and all of a sudden I get the following error:Winsock Connect Error:System Error 10060System Message:A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.I believe there were settings changed in the group policy that does not allow a client to respond to the remote calls because it stopped working from 1 day to the next.Still the same OS Windows 7.I do not have any problems at all to install/uninstall the service via network on the client computers thru the MRC.Using it on my servers it works p