ctx_ima_startimaservice error 1053
or pause a service Modified on: Tue, 26 Apr, 2016 at 12:13 PM PROBLEM When attempting to start, stop or pause a service, one of the following error error 1053 windows 7 messages is encountered: "Error 1053: The service did not respond to the start error 1053 windows server 2012 or control request in a timely fashion.""Error 7000: The Error 1053 Windows Server 2012 R2
service. This time-out period is typically less than 30 seconds. If you do not adjust this time-out period, the Service Control Manager ends the process. To adjust this time-out period, follow these steps:IMPORTANT: Incorrect use of the Microsoft Windows Registry Editor may cause serious problems with your computer, up to and including general operating system corruption and inability to boot. Registry editing should only be performed by those who are sufficiently experienced in the use of the registry editor application. Go to Start > Run > and type regedit Navigate to: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control With the control folder selected, right click in the pane on the right and select new DWORD Value Name the new DWORD: ServicesPipeTimeout Right-click ServicesPipeTimeout, and then click Modify Click Decimal, type '180000', and then click OK Restart the computer CAUSE The Microsoft Windows Service Control Manager controls the state (i.e., started, stopped, paused, etc.) of all installed Windows services. By default, the Service Control Manager will wait 30,000 milliseconds (30 seconds) for a service to respond. However, certain configurations, technical restrictions, or performance issues may result in the service taking longer th
password CAPTCHAThis question is for testing whether or not you are a human visitor and to prevent automated spam submissions. Error 1053: with MFcom Service Submitted by RoyATokeshi on Sun, 02/22/2004 - 08:57 Citrix states in their article: CTX916786
Error 1053 Windows Server 2003
CTX916786 - Error 1053: with MFcom Service This document was published at: http://support.citrix.com/kb/entry.jspa?externalID=CTX916786 Document ID: error 1053 windows 8 CTX916786, Created on: Feb 6, 2002, Updated: Apr 23, 2003 Products: Citrix MetaFrame XP 1.0 for Microsoft Windows 2000 Modify the windows service 1053 error during startup registry setting that is referenced in the SP1/FR1 readme. After installing the Oracle Client Version 7.3.3 and rebooting the server, the MFCOM service failed to start. Increasing the TimeOut Value, stated in the SP1/FR1 for MetaFrame https://support.threattracksecurity.com/support/solutions/articles/1000071019-error-1053-the-service-did-not-respond-in-a-timely-fashion-when-attempting-to-start-stop-or-pause XP readme, resolved the issue. MFCOM Service Timeout MetaFrame COM Server (MFCOM) is a service that starts when a MetaFrame XP server starts up. The IMA service must be running for MFCOM to start. If a Service failed to start message appears when you restart a server, check the Event Log (Terminal Server) or the System Log (Windows 2000 Server). If the messages "IMA service hung on starting" and "MFCOM service failed to http://tokeshi.com/node/1875 start" are in the log, IMA service did not start within three minutes, the default timeout period for the MFCOM service. Timeout of the MFCOM service at startup is not a problem, because MFCOM will start later if it is needed. To prevent MFCOM from timing out, edit the following registry key, which sets the amount of time that MFCOM waits for the IMA service to start: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\MFCom\IMAWaitTimeout Set the value to 1,200,000 milliseconds (20 minutes) or higher. The following registry key controls the time MFCOM waits before polling the IMA service for its status: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\MFCom\IMAWaitPause The default value is 30,000 milliseconds (30 seconds), which works well in most cases. A value of -1 of timeout indicates to wait indefinitely. Note: MFCOM is a COM server that supports the API calls defined in the Citrix Server SDK. If the CWC, Citrix Web Console, which is based on MFCOM, or any other application based on MFCOM, is not being used, the MFCOM Service can be disabled via the control panel. The Citrix server SDK can be obtained through a registration process from the CDN (Citrix Develop Network) at www.citrix.com (Click on the developer link) or http://apps.citrix.com/cdn/. Google+ DISCLAIMER: None of this has anything to do with us, someone else is responsible for the entire thing, aa timely fashion From: "Jim Kenzig http://ThinHelp.com"
WindowsServer2003環境にCPS4.5(データストアはORACLE)をセットアップしておりますが Presentation Serverのインスール時に以下のエラーが発生してしまい先に進めません。 エラー 26008。IMAサービスの起動時にエラーが発生しました(CTX_IMA_StartIMAService Error = 1053(0X0))。 関連するサービスが起動しているか?データストアに接続可能か? ODBC接続可能か?など環境周りを確認しましたが解決に至っておりません。 どなたか対応方法・確認箇所等の情報をお持ちでしたらご教示頂けないでしょうか。 よろしくお願いします。 kunimari posted this message at 2009/07/28 20:31:24 metameta様 私は下記のようエラーでした。(微妙に違うのは、当方はデータストアをACCESSで 設定してるからかもしれません) 26005. IMAサービスを起動できませんTX_MF_IMA_StartIMAService State = 1 CITRIXのKNOWLEDGE CENTERにて以下の情報を発見しました。 CTX104843 「IMAサービスを起動できませんCTX_MF_IMA_StartIMAService。」というエラーメッセージが表示される 解決方法] この現象は、データストアが大きくなっている場合、またはMetaFrameサーバーとデータストア間のWANリンクが低速な場合に発生します。 インストール中にサービスコントロールマネージャがタイムアウトするため、IMAサービスが起動に失敗します。 IMAサービスの起動に時間がかかる場合、インストールのロールバックが原因でサービスコントロールマネージャのエラーメッセージが表示されます。その場合は、サービスコントロールマネージャのタイムアウト値を設定する必要があります。タイムアウト値を設定するには、以下のレジストリキーに値を追加します。 注: レジストリエディタの使用を誤ると、深刻な問題が発生する可能性があり、Windowsの再インストールが必要になることがあります。レジストリエディタは自己の責任と判断の範囲でご使用ください。 HKEY_LOCAL_MACHINE¥SYSTEM¥CurrentControlSet¥Control¥ServicesPipeTimeoutへ移動し、以下の値