Canon Error 063
Contents |
Xerox, Canon, Brother, Hp, Toshiba, Panasonic, Ricoh
Return to main menu Canon G3 Error Codes Canon G3 error Codes / G3 Service Code At bottom Of Page ( All information is for experienced technicians and is to be used carefully, we do not guarantee canon copier error codes info to be accurate or correct) G3 Error Codes ##001 [ TX ] Fail to receive canon printer error codes phase OK signal in FAX/TEL mode. A. Cause: Other party cannot properly receive phase signal due to poor line conditions. Solution: Boost theCanon Camera Error Codes
transmission level so the other party can receive the phase signal properly. Solution: Adjust the NL equalizer so the other party can receive the phase signal properly. ##002 [ RX ] Picture memory full upon G2 reception. A.
Canon Digital Camera Error Codes
Cause: Defective buffer memory. Solution: Replace the SCNT PWB. ##003 [ TX ] Failed MCF2/ PIS reception during G2 transmission. A. Cause: Other party cannot properly receive signals due to poor line conditions. Solution: Boost the transmission level so the other party can receive MCF2 or PIS. Solution: Adjust the NL equalizer so the other party can receive MCF2 or PIS signals properly. ##004 [ RX ] Fail EOM/ PIS reception during G2 reception. A. canon eos error codes Cause: Picture signal cannot be received over 1 second due to poor line conditions. Solution: Boost the transmission level so the other party can receive EOM or PIS signal properly. Solution: Adjust the NL equalizer so the other party can receive EOM or PIS signal properly. ##005 [ TX ] Failed G12 reception during G2 transmission. A. Cause: Other party cannot properly receive the G12 signals due to poor line conditions. Solution: Have the other party boost their transmission level so they can properly receive G12 signal. B. Cause: Other party confused by echo and does not send G12. Solution: Have the other party lower their transmission level so they will not receive echo signals. ##006 [ RX ] Failed phase synchronization from second sheet during G2 reception. A. Cause: Other party cannot properly receive phase signal due to poor line conditions. Solution: Have the other party boost their transmission level to allow for proper phase signal reception. Solution: Adjust the NL equalizer so the other party can receive the phase signal properly. ##007 [ TX ] Failed CFR2 reception during G2 transmission. A. Cause: The other party cannot receive CFR2 due to poor line conditions. Solution: Boost the transmission level so the other party can receive CFR2 properly. Solution: Adjust the NL equalizer so the other party can receive CFR2 signal properly. B. Cause: The other machine i
home position of the duplexing unit feed roller cannot bedetected.E055 The horizontal registration guide of the duplex unit exceeds itsmaximum travel distance.E060 The home position of the
Canon Rebel Error Codes
primary corona wire cleaner cannot bedetected within a specific time.Relateted chargingE061 Specific canon error codes pixma potential is not be required or the limiter is activated as thepotential is controlled.E062 The photosensitive drum temperature does canon mg3250 error codes not reach a specificvalue due to a fault in the photosensitive drum heater, etc.E063The home position of the transfer corona wire cleaner cannot bedetected.An error code isnot to beindicated.E064 The setting value http://www.worldoffax.com/G3%20Service%20Codes.htm for the output from the microcomputerconsiderably deviates from the control value of the actual output.E065 High voltage leakage from the primary corona assembly isdetected.E066 Signals from the temperature/humidity sensor cannot be detected.E067Two or more faults in the primary/ pre (post)-transfer/ transfer/separation high voltage are detected (including power outputstoppage, electric leakage from the primary corona assembly).E068 High voltage leakage from or an open circuit http://fileresetter.blogspot.com/2004/02/canon-error-code-e051e054-e055-e060.html in the separationcorona assembly is detected.E069 High voltage leakage from or an open circuit in the transfer coronaassembly is detected.E070 The home position of the transfer drum cannot be detected within a specific time.E071 An image leading edge signal cannot be detected within a specifictime.E072 A fault in the main motors such as the transfer drum motor, etc. Posting Lebih Baru Posting Lama Beranda Search Entri Populer resetter epson r230x (SSC Service Utilily) 1 . Make sure the printer is turned on and terkonek with a computer ( printer driver already installed ) 2 . Install SSC Service... Epson C110, CX7300, CX8300 & CX9300 Printer please download these resetter below free ( you only have for post in quest book ) Epson CX9300F Adjustment Epson CX8300 Adjustment Epson C1... Service tool pixma ip2770 (Resetter Pixma iP2270) steps reset canon pixma iP22700: - Log on to the service mode first connect the printer to the computer and the power cord... Category Adjustment Program Epson and Scanner Automate Ink Injector BCI-7e BCI-9 canon Canon LBP 5300 canon BJ F900 Canon BJC 2100 Canon BJC-2100SP Waste Error R
Reparación de Fotocopiadoras » Error E063 Canon IR600 Error E063 Canon IR600 04/5/2012 06:41PM Tengo claro que es un error en el limpiador http://impresoras.yoreparo.com/reparacion_de_fotocopiadoras/error-e063-canon-ir600-t898721.html de hilos de corona, por lo que quiero desactivarlo, doy la opcion *28* COPIER/OPTIONS/BODY/ pero me da la sigueinte opcion para poder desactivarlo con 0 me salen unos codigos y numeros....si alguien sabe como hacelo se lo agradeceria. SAludos rofo18 1 ¿Sabes la respuesta?Responder 05/5/2012 04:05AM ok sigue error codes esta ruta y comentas suerte preciona *2.8* , copier, option, body, cln-w si esta opcion esta en 1 cambialo a 0 rigoberto hernandez 93 05/5/2012 12:46PM el error 014 es el motor de recoleccion de toner que va atras el la botella de toner de dececho de toner camera error codes verifica que no este llena y verificar motor . carlos hurtado gonzalez 4 Bienvenido/a! YoReparo es la mayor comunidad sobre tecnología. Colaboramos y compartimos información para solucionar todo tipo de problemas técnicos. Para participar solo hace falta que te registres gratis aquí Temas Impresoras y Copiadoras Impresoras y Scanners Reparación de Fotocopiadoras Reciclado Cartuchos y Toner Hardware y Computadoras Sistemas Operativos y Software Celulares y Telefonía TV y Video Audio Cámaras Consolas de Videojuegos Electrónica Electrodomésticos y Línea Blanca Hogar Mecánica y Automóviles Internet Programación y Desarrollo Balanzas y Registradoras Seguridad y Alarmas Electromedicina Industria De Todo Comunidad Nuevo YoReparo Todos los Foros | © 2002-2016 Ilirey SA. Todos los derechos reservados. Reglamento Acerca Mapa del Sitio Libros Contacto Facebook Terminos y Condiciones Denunciar Abuso Club del Service: Cursos, Libros, y todo para el Técnico Club de Diagramas: Diagramas y Manuales de Servicio