Error Reading From Disk
Contents |
Gaming Smartphones Tablets Windows 8 PSUs Android Your question Get the answer Tom's Hardware>Forum>Storage>Solution for "A disk read error occurred."> Closed Solution for "A disk read error occurred." Tags: Hard Drives Disk Read Error Storage Last response: 2 April 2011 22:05 in Storage wii error reading disk message Share pbarney 17 June 2009 22:13:43 This is one of the most frustrating error messages wii error reading disk fix you can ever deal with. Sometimes the fix is simple, sometimes it's a complete pain. Having recently dealt with this again, I thought what do you do if your wii wont read a disk I'd post my thoughts in the hopes that it helps someone else out there. So you receive the dreaded "a disk read error occurred. Press Ctrl+Alt+Del to restart". Multiple restarts result in the same error message. If you https://www.raymond.cc/blog/help-a-disk-read-error-occurred-press-ctrlaltdelete-to-restart/ put your drive into another computer, or connecting it as a slave on your own computer, it will typically work fine, and no data is missing. Because this error is not usually associated with data loss, DO NOT RE-PARTITION THE DRIVE. Your data is likely safe and sound. Here's how we'll recover your data. Try each step below, in order, and see if your drive becomes accessible after each step. In my experience, you won't start seeing http://www.tomshardware.com/forum/250364-32-solution-disk-read-error-occurred results until step 5 or so. 1. Run CHKDSK /R /P from the recovery console (it will typically find no error) 2. run FIXBOOT from recovery console (typically has no result) 3. run FIXMBR from recovery console (typically has no result) 4. Run the manufacturer's diagnostic utility, downloaded from their website (it will typically find no error) 5. Changing the drives from cable select to Master/Slave may fix it. 6. Replacing the data cable may fix it, but usually not. 7. Setting the BIOS to use defaults may fix it, but usually not. 8. Changing the BIOS drive settings from auto to user-specified, ensuring that LBA is selected may fix it. 9. Pulling the CMOS battery to let the BIOS lose it settings may work. At this point, you may be feeling some frustration. :-) If all that fails, here's what will usually work: Ghost your data to a new drive, and use the original one as a slave. It will work. And all of your data will still be accessible. Your computer should boot normally. If it doesn't, or it there are errors, run the Repair Installation option from your Windows boot CD. But why does this happen? Nobody seems to know why. The problem typically evades all forms of detection. Here's what I've learned: this error message likely has more to do with a ha
Fix for Windows XP, Vista, 7, 8 September 23, 2016 Get the fix for the error A disk read error occurred on Windows XP, Windows Vista and Windows 7. Contents1 About "A disk read https://neosmart.net/wiki/a-disk-read-error-occurred/ error occurred"1.1 Description and Symptoms1.2 Symptom 1: "A disk read error occurred" error https://appuals.com/steps-to-fix-a-disk-read-error-occurred/ screen on startup2 Causes of this Error2.1 Cause 1: Incorrect or invalid MBR configuration2.2 Cause 2: Misconfigured partition table3 Fixing “A disk read error occurred” on Windows3.1 Fix #1: Use Easy Recovery Essentials3.2 Fix #2: Check RAM memory3.3 Fix #3: Check Hard Disk Cables3.4 Fix #4: Reset or Upgrade BIOS3.5 Fix #5: Run chkdsk3.6 Fix error reading #6: Run bootrec4 More Information4.1 Linked Entries4.2 Support Links4.3 Applicable Systems About "A disk read error occurred" The following information on this error has been compiled by NeoSmart Technologies, based on the information gathered and reported by our global network of engineers, developers, and technicians or partner organizations. Description and Symptoms The error messages, alerts, warnings, and symptoms below are tied to this error. Symptom 1: error reading disk "A disk read error occurred" error screen on startup The "A disk read error occurred error" appears on a black screen without an identifiable error code. Pressing the Ctrl, Alt and Del keys will only restart the computer and boot into the same error screen: A disk read error occurred Press Ctrl+Alt+Del to restart In most cases the error can appear for any of the following reasons: Incorrect or invalid MBR configuration Improperly configured partition table Faulty hard drive IDE cables failing Bad RAM memory Issues with your computer's BIOS version The most common cases of this error are attributable to an incorrectly-flashed MBR to the system startup disk or the absence of an active partition on the startup disk. In these situations, the recommendations below should resolve the problem readily. If the problem is with hardware, additional diagnosis and the possible replacement of system components may be needed. Causes of this Error This error has been known to occur as a result of one of the following causes: Cause 1: Incorrect or invalid MBR configuration The most common cause for this error is an incorrect MBR configuration. This is usually caused by disk write errors, virus attack
Comments The “A disk read error has occurred” error is an extremely dreadful error message that appears as soon as a computer boots up and does not allow an affected computer to boot into its Operating System, essentially locking the user out of the computer. In its fullest form, this error message reads “A desk read error has occurred. Press Ctrl+Alt+Del to restart.” Affected users are met with the “A desk read error has occurred” error no matter how many times they reboot their computer as this is not an issue that can be fixed by a simple restart. The “A disk read error has occurred” error message points towards a problem with a computer’s hard drive or issues during the process of reading said hard drive. However, the actual cause of this issue varies from one affected computer to the other and can be anything from a hardware issue to a software issue. This is why there is no set resolution or fix for this issue. However, there are quite a few different solutions that you can try out in order to try and fix the issue on your own, and the following are some of the most effective ones: How to BOOT into BIOS to change Boot Order You must know how to boot and change boot order since this will be needed to perform the solutions below. Restart your computer. Enter your computer’s BIOS (or UEFI) settings as soon as it starts up. The key that you need to press to enter these settings depends on the manufacturer of your computer’s motherboard and can be anything from Esc, Delete or F2 to F8, F10 or F12, usually F2. This is displayed on the post screen, and the manual that was supplied with your system. A quick google search asking "how to enter bios" followed by model number will also list results. Navigate to the Boot. Solution 1: Check to see if your hard disk has failed or is failing A failed or failing hard disk can also be the root of this issue. To check to see if you hard disk drive is failing or has failed, you need to: Go here and download an ISO file for Easy Recovery Essentials. Burn the ISO file to a CD/DVD or a USB using MagicISO or other free burning software. Insert the media into the affected computer, restart it and then boot from the media. Click on Automated Repair. Click on Continue. Wait for the Automated Repair to be completed. Once the process has reached completion, you will be informed if either your hard disk drive or RAM has failed or is failing. If you find that your HDD really has failed or is failing, replacing it with a new one and then starting over with a new installation of Windows should fix the “Reboot and sel