Raid Controller Error Message
Contents |
Türkçe 简体中文 How to Troubleshoot Hard Drives and RAID Controller Errors on Dell PowerEdge 12G This article provides information on how to troubleshoot hard drive and RAID Controller errors on Dell PowerEdge™ 12G Servers. Show all foreign configuration found on adapter | Hide all Issue 1: Post Error Messages Message Meaning There are
Foreign Configuration Found On Adapter Press Any Key To Continue Or C
X enclosures connected to connector Y, but only maximum of 4 enclosures can be connected to a single
Bad Missing Or Unsupported Raid Controller Memory Module Detected
SAS connector. Please remove the extra enclosures then restart your system. When the BIOS detects more than 4 enclosures connected to a single SAS connector, it displays this message. You
There Are Offline Or Missing Virtual Drives With Preserved Cache
must remove all additional enclosures and restart your system. Cache data was lost, but the controller has recovered. This could be due to the fact that your controller had protected cache after an unexpected power loss and your system was without power longer than the battery backup time. Press any key to continue or 'C' to load the configuration utility. This dell raid foreign configuration found message displays under the following conditions: The adapter detects that the cache in the controller cache has not yet been written to the disk subsystem. The controller detects an Error- Correcting Code (ECC) error while performing its cache checking routine during initialization. The controller discards the cache rather than sending it to the disk subsystem because the data integrity cannot be guaranteed. To resolve this problem, allow the battery to charge fully. If the problem persists, the battery or adapter DIMM might be faulty. The following virtual disks have missing disks: (x). If you proceed (or load the configuration utility), these virtual disks will be marked OFFLINE and will be inaccessible. Please check your cables and ensure all disks are present. Press any key to continue, or 'C' to load the configuration utility. The message indicates that some configured disks were removed. If the disks were not removed, they are no longer accessible. The SAS cables for your system might be improperly connected. Check the cable connections and fix any problems. Restart the system. If there are no cable problems, p
messages, refer to the Sun StorEdge 3000 Family RAID Firmware User’s Guide. Error Codes Error and Status Messages Installation and Program Prompts Error Codes Shown and described in the Event Log, multibit ecc errors were detected on the raid controller an error code is an eight-character code that consists of four fields of two characters import foreign configuration dell perc each. Some codes might be followed by a dash and another eight-character code, which is for internal use only. The following tables there are offline or missing virtual drives with preserved cache ibm describe the error codes used in each two-character field. The format of the four fields of two characters is: d1d2d3d4-d5d6d7d8 where d1 = the Severity Field d2 = the Major Field d3 = the Minor Field (determines http://www.dell.com/support/article/us/en/04/SLN129432/en how d4, d5, d6, d7, and d8 are decoded) TABLE G-1 Severity Field Severity Field Description 01 Critical 02 Warning 03 Informational TABLE G-2 Major Field Major Field Description 01 Unknown 05 06 Monitor daemon 08 Server daemon 09 JBOD (Just a bunch of disks) message 0A Communication 0B RAID Controller The Minor field is defined in following table. The definition of the Error Field is dependent upon the definition of the Minor https://docs.oracle.com/cd/E19168-01/817-3337-18/appg_error_mess.html Field in which case the appropriate Table is referenced. TABLE G-3 Minor Field Minor Field Description 01 Unknown 02 See Error Field: System Drive State. 03 See Error Field: Disk State. 04 See Error Field: SAF-TE State. 05 See Error Field: Tape State. 06 See Error Field: Redundancy State. 07 See Error Field: Internal State. 08 See Error Field: Device State. 09 See Error Field: Initialization State. 0A See Error Field: Invalid Client Parameter. 0B See Error Field: Open Transport. 0C See Error Field: Close Transport. 0D See Error Field: Memory Allocation. 0E RaidCard fault detected. 10 See Error Field: Transport. 11 See Error Field: Main Communications. 12 See Error Field: Communication Link. 13 See Error Field: Communications Async. 14 See Error Field: Communications Security. 15 See Error Field: Timeout. 16 See Error Field: Administration. 17 See Error Field: Firmware. 18 See Error Field: System Shutdown. 19 Dynamic Growth fault detected. 1C See Error Field: Set Config. 1D See Error Field: Controller Event. 1E See Error Field: Drive Side Event. 1F See Error Field: Host Side Event. 20 See Error Field: Logical Drive Event. 23 See Server Manage/Monitor Event Error. 2B See Error Field: Generalized Target Event Error Field: System Drive State TABLE G-4 System Drive State Errors Error Field 01 Offline 02 Degraded 03 Online 04 Unknown 05 P
Wireless Forums. User Name Remember Me? Password Register FAQ Forum Rules Members List Calendar Today's Posts Advertise Search http://www.wirelessforums.org/alt-comp-hardware/error-occurred-0-raid-0-what-does-mean-14336.html Search Forums Show Threads Show Posts Tag Search Advanced Search Go to Page... LinkBack Thread Tools Display Modes #1 (permalink) 01-07-2007, 02:11 PM John Guest Posts: n/a "Error Occurred(0)" with RAID 0. What does it mean? During boot up, one of my two week old hard disks in my foreign configuration RAID 0 is now reporting this error: "Error Occurred(0)" I googled for this error message and found only one other person that reported this error and his screen snapshot is nearly identical to my problem. http://www.hardforum.com/showthread.php?t=1132761 None of the responses that I read in that thread were helpful to me. Using Western Digital diagnostic tools, I foreign configuration found tested each drive and no errors in either drive were discovered. Chkdsk also reported no errors. From the time I first observed this error message some days ago, the computer has been working without any apparent problems (boots up and runs just fine) but the error message is driving me nuts. I have two of these disks: Western Digital Caviar SE16 WD3200KS 320GB 7200 RPM 16MB Cache SATA RAID 0 with Intel Matrix Storage Manager Motherboard: ASUS P5B-E (latest BIOS installed). Intel ICH86/DO/DH SATA RAID Controller: Driver date: 5/11/06 Driver version: 6.0.0.1022 JMicron JMB36X Controller: Device type: SCSI and RAID controllers Manufacturer: JMicron Technology Driver date: 12/5/2006 Driver version: 1.17.8.1 Device manager reports no errors for either of the above controllers. XP Professional. All service packs and updates installed. Intel Core 2 Duo E6600 Conroe 2.4GHz 4M shared L2 Cache LGA 775 Processor Does anyone have any suggestions on how I can resolve this error message? #2 (permalink) 01-07-2007, 03:11 PM HDRDTD Gues