425 Error Ftp Connection
Contents |
are UTC 425 Can't Open Data Connection Moderator: Project members Post new topic Reply to topic Page 1 of 2 [ 28 posts ] Go to page 1 2 Next Print view Previous topic | Next topic Author ftp error 425 no data connection Message jkemper08 Post subject: 425 Can't Open Data ConnectionPostPosted: 2012-05-24 17:20 Offline 500 Command ftp error 425 can't build data connection connection timed out not understood Joined: 2012-05-24 16:44 Posts: 1 First name: Jesse Last name: Kemper Okay so I've setup a server on Windows 7 with ftp error 425 failed to establish connection DynDNS. So far I've configured DynDNS properly and set the settings in the firewall to allow connections inbound and outbound on port 21. But still I get this error..... Quote:425 Can't open data connection.Failed to retrieve directory ftp error 425 can't open data connection listing.It tells me that the user is logged in appropriately but it is not dropping them into there home folder or allowing them to connect/transfer any data etc. I've set both server/client to use passive mode, and I'm fairly sure the firewall is configured correctly as well, so now I'm pulling my hair out, any help would be appreciated. Attachments: ftp error.png [ 102.75 KiB | Viewed 257955 times ] Top Profile Reply with
Ftp Error 425 Unable To Open Data Connection
quote boco Post subject: Re: 425 Can't Open Data ConnectionPostPosted: 2012-05-24 21:26 Offline Contributor Joined: 2006-05-01 03:28 Posts: 22684 Location: Germany Quote:So far I've configured DynDNS properly and set the settings in the firewall to allow connections inbound and outbound on port 21. But still I get this error.....Code:425 Can't open data connection.Failed to retrieve directory listing.Yes, of course, because the listings and transfers do NOT use port 21. In the screenshot, the port offered was 49389 (192*256+237). So, in addition to the listening port, you need to define, open and forward a range of ports for Passive data connections (minimum recommended 100 ports). Please refer to the Network Configuration guide for details. Besides, in case you are behind a router and test from your own LAN, use the private LAN IP to connect. _________________### BEGIN SIGNATURE BLOCK ###No support requests per PM! You will NOT get any reply!!!FTP connection problems? Do yourself a favor and read Network Configuration.All FileZilla products fully support IPv6. http://worldipv6launch.org### END SIGNATURE BLOCK ### Top Profile Reply with quote fredcrys Post subject: Re: 425 Can't Open Data ConnectionPostPosted: 2012-08-13 20:57 Offline 500 Command not understood Joined: 2012-08-13 19:06 Posts: 2 First name: Freddy Last name: Camacho HI,I also have the problem with the 425 error code. The sever is behind a router (D-link DIR-825)
7 DynDNS Explained 7.1 External IP Address 7.2 Internal vs. External IP Address 8 Device Specific Instructions 8.1 Apple Airport Extreme Introduction[edit] This is a How-to
Ftp Error 425 Security Bad Ip Connecting
guide on how to set up your router with FileZilla Server (FZS) in ftp 425 error filezilla order to fix the error code 425. There is a Wiki on Network Configuration that covers this information, however, it ftp error 425 use port or pasv first is written in such a way that the “layman” may have difficulty understanding what’s going on—and it doesn’t show exactly how to fix the 425 error code—so this Wiki will give instructions on https://forum.filezilla-project.org/viewtopic.php?t=24925 how to set up your specific router. ”Abstract”[edit] This Wiki will go over the common technical reason(s) for error 425 being given after the FZS sends the 227 Passive command to the FTP client—regardless of what client is being used. This Wiki is written for the common user in a narrative tone—if a more in-depth technical Wiki is desired refer to the Network Configuration article. Narrative[edit] So, https://wiki.filezilla-project.org/Setting_up_your_Router_to_Fix_the_%22425_code%22 you've set up your FZS and it works for a local connection in your home, BUT you want to make your Local FTP Server accessible when you’re away—and you want to use encryption (SSL/TLS) to do so. You set up a Dynamic DNS (DynDNS) service to point to your FZS via your external IP address (don’t worry I’ll explain later in the Wiki). You’ve followed a how-to on setting up FZS to use SSL/TLS, but you've run into an issue—and after looking at the FZS Log you see the problem—right after the "227 Passive command" is given and acknowledged you see a 425 error. But even after summoning a Warlock, a Witch, and a Unicorn—you can’t fix it and wind up here reading this Wiki. The Problem[edit] More than likely the problem is that your FZS is requesting the FTP Client to use the Passive Ports defined in the FZS settings. And even though you’ve changed the settings in your Windows 7 or 8 Firewall you still can’t get your FTP Client to connect. Why? Well it’s complicated; the type of encryption that FZS uses doesn’t allow the router to “see” that you’d like to allow this communica
iSeries SENDPASV; cannot open data connection; FTP Technote (troubleshooting) Problem(Abstract) Error 425 Cannot open data connection by running FTP communications Cause The data http://www-01.ibm.com/support/docview.wss?uid=swg21523306 connection (for a directory listing, upload, or download) was unable to be established. The most common solution: change the active/passive mode settings. The most common reason that this error occurs is a mis-configuration of the FTP server software itself, related to SSL connections and firewalls, in which the connection tries to establish itself on a bad IP address. You can set your FTP server ftp error up to use the Extended Passive Mode (EPSV) command. The EPSV command only sends the port and the IP address is inferred to be the same as the IP address of the control connection. Your server is configured to always use the same port for passive mode connections, or the client is configured to always use the same port for active mode connections, ftp error 425 although in this case usually the software in question should raise a different error first. In passive mode, the firewall in front of the FTP server does not have the correct ports open.So the server tells the client to connect to IP address 1.2.3.4 on port x, but the firewall does not allow incoming connections on port x. Most firewalls are smart enough to open up the port when it sees the PASV response. Vice versa for active mode and the firewall in front of the FTP client. Resolving the problem The OS/400 automatically sends in passive mode. To make the OS/400 run in active (non-passive) mode enter the OS/400 FTP client command SENDPASV, coded as a Tran=C in the session control script of the Communication profile. NOTE: Try also passive mode (depending on connection) SENDPASV 1 Historical Number SCI86400 Document information More support for: Sterling Gentran:Server for iSeries Software version: 3.5, 3.6 Operating system(s): IBM i Reference #: 1523306 Modified date: 2011-10-07 Site availability Site assistance Contact and feedback Need support? Submit feedback to IBM Support 1-800-IBM-7378 (USA) Directory of worldwide contacts Contact Privacy Terms of use Accessibility