4600 50.2 Error
Contents |
Account Login Shopping Cart My Account Checkout Home Troubleshooting 50.2 fuser error HP LaserJet 4000 4050 4100 4200 4300 Email Loose fuser tabs on the HP LaserJet 4000, 4050, 4100, 4200, 4300 - a potential 50.2 error If you are experiencing 50.2 fuser error a "50.2" fuser error, first turn the printer off and back on. Sometimes 50.2 fuser error laserjet pro 400 the error will temporarily go away with a reboot so you can print a few more pages, but usually the
Fuser Error Hp Printer
error reappears. If you recently moved the printer around or if you recently installed a new fuser, particularly on HP LaserJet 4000, 4050, 4100, 4200, or 4300 series printers, you should check to
50.2 Fuser Error Hp 4525
see if two tabs on the fuser have come loose. (They can get dislodged during shipping, heavy movement, or during fuser installation.) See more info below on these tabs. If you have NOT recently replaced the fuser or heavily jostled the printer around, then the 50.2 Fuser error indicates you may have an actual fuser failure and the fuser needs replacing. Fusers are a consumable part 50.0 fuser error hp laserjet p1102 and they are the main component in a printer maintenance kit; it is expected over the life of the printer you will replace the fuser / maintenance kit several times. Click here to see our list of available maintenance kits for each model printer. Most fuser models can be installed by an end user, without needing a service technician. We have installation instructions under the Tech Support section of our Web site. Call us with any questions @ 608-831-2396 or toll-free 866-352-7108. In case you have moved the printer around recently or if you installed a replacement fuser recently -- Here are instructions for checking those fuser tabs on your LaserJet 4000, 4100, 4200, 4300, 4250, 4350 series fuser: Turn your printer off and remove your fuser. Flip it to the gear side (the left side) and press inwards on the fuser tab to make sure it is fully clicked in place, as shown below. Then flip the fuser over to the right side (the non-gear side) and press in on the other fuser tab to make sure it is also fully clicked in place. (right side of a LaserJet 4000/4050 fuser pictured below) (right si
the wall voltage. If on a surge protector plug straight in two the wall.3. Bad fuser ass'y.4.
50.2 Fuser Error P4015
Bad low voltage power supply5. Bad D.C. controller HP LASER PRINTERS 2, 2D, 50.1 fuser error 3, 3D 1. Defective fuser cable to DC controller. 2. Defective fuser and AC power supply 3. Defective fuser. 50.3 fuser error 4. Defective AC power. 5. Temporary error code. HP LASER PRINTERS 2P, 2P+, 3P 1. Defective fuser. 2. Temporary error code. 3. Defective ac power supply. HP LASER PRINTERS 3SI, 4SI http://www.printertechs.com/printer-troubleshooting/11-50-2-fuser-error 1.Temporary error code. Turn printer off then wait 20 or 30 minutes the turn back on 2. Improperly seated fuser. 3. Defective fuser. 4. Bad ac power supply.5. Bad D.C. controller HP LASER PRINTERS 4, 4+, 5 1. Temporary error code. Turn printer off then wait 20 or 30 minutes the turn back on. 2. Defective fuser.3. Defective DC/AC power supply4. Change http://www.advancedlaser-hp-error-codes.com/error_50.htm cable from fuser to power supply HP LASER PRINTERS 4V, 4L, 4P, 5P, 6P 1. Improperly seated fuser. 2. Defective fuser. 3. Bad engine board HP LASER PRINTERS 5L, 6L 1. Defective fuser. 2. Defective D.C. controller.HP LASER PRINTER 1100, 2100, 4000, 40501. Turn printer off then wait 20 or 30 minutes.2. If printer is hooked up to uninterruptible power supply or surge protector plug straight in to wall.2. Replace fuser ass'y3. Replace engine board. HP LASER PRINTER 1200, 2200, 3100 FAX, 3200 FAX, 4100, 4100MFP 1. Turn printer off then wait 20 or 30 minutes 2. Improperly seated fuser. 4. Defective fuser.Replace the fuser ass'y 3. Temporary error code. 5. If the error persists, replace the ECU. HP LASER PRINTER 20151. Unplug the printer, and then plug it in again.2. Reseat the formatter cable in the ECU.3. If the error persists, replace the formatter.3. If after replacing the formatter, the error persists, replace the ECU. HP LASER PRINTER 2300 ERROR 50.X1. A fuser error has occurred.2. Turn printer of and then on again.3. Replace the fuser ass'y4. Replace the engine board.5. If you still have a proble
Copier and Fax Repair 260-417-4807 Brother Tech ArticlesCanon Tech ArticlesCopyStar Tech ArticlesDell Tech ArticlesHP Tech ArticlesKyocera Tech ArticlesLexmark Tech ArticlesOkidata Tech ArticlesSamsung Tech ArticlesXerox Phaser Tech Articles http://www.fortwayneprinterrepair.com/wordpress/2011/12/18/50-2-fuser-error-hp-color-laserjet/ 50.2 Fuser Error - HP Color Laserjet 4700, 4730 MFP, CP4005 4700 / 4730 / CP4005, HP Tech Articles Add commentsDec 182011 50.2 fuser error - HP Color Laserjet 4700, 4730 MFP, CP4005Lots of factors can result in the HP color laserjet 4700, 4730 MFP, and CP4005 printers displaying a 50.2 fuser error. The 50.2 fuser error is a result of the fuser error machine not properly warming up before it's time to print. The thermistors inside the fuser measure the temperature as the machine warms up. If after a certain amount of time the fusing unit, HP Color LJ 4700, 4730, and CP4005 Fuser, RM1-3131-000, Q7502A, has not reached its operating temperature the machine informs the end-user by displaying the 50.2 fuser error.First thing to check is 50.2 fuser error the power source. Make sure the machine is plugged straight into the wall outlet and not on a power strip with other devices.Second is to just turn the machine off and back on. If the fusing assembly is still hot then maybe a little extra time will get it to its operating temp. might not be a permanent solution but will get you working for a time. The heating elements do get worn out and take longer to warmup. If you see this error happen more than once and turning it off and back on fixes it then I would get a fusing assembly on order and replace it as soon as possible because the 50.23 fuser error most likely continue to come back until it doesn't work any more.Third is to check the environment. Make sure the machine is not in an extreme cold environment as this can result in warmup issues. Or if you just brought it in from outside in the winter you should let the machine sit 2 to 4 hours before using.HP Color Laserjet 4700, 4730 MFP, CP4005 Fuser Removal1. Turn the printer