50.2 Fuser Error 4350
Contents |
Account Login Shopping Cart My Account Checkout Home Troubleshooting 50.2 fuser error HP LaserJet 4000 4050 4100 4200 4300 Email Loose fuser tabs on the HP LaserJet 4000, 4050, 4100, 4200, 4300 - a potential 50.2 error If you are experiencing a "50.2" fuser error, first turn the printer off 50.2 fuser error laserjet 4250 and back on. Sometimes the error will temporarily go away with a reboot so you
Xerox 4250 Fuser Warm Up Error
can print a few more pages, but usually the error reappears. If you recently moved the printer around or if you recently
50.2 Fuser Error P4015
installed a new fuser, particularly on HP LaserJet 4000, 4050, 4100, 4200, or 4300 series printers, you should check to see if two tabs on the fuser have come loose. (They can get dislodged during shipping, heavy
50.2 Fuser Error Laserjet Pro 400
movement, or during fuser installation.) See more info below on these tabs. If you have NOT recently replaced the fuser or heavily jostled the printer around, then the 50.2 Fuser error indicates you may have an actual fuser failure and the fuser needs replacing. Fusers are a consumable part and they are the main component in a printer maintenance kit; it is expected over the life of the printer you will replace the fuser / 50.2 fuser error hp 4700 maintenance kit several times. Click here to see our list of available maintenance kits for each model printer. Most fuser models can be installed by an end user, without needing a service technician. We have installation instructions under the Tech Support section of our Web site. Call us with any questions @ 608-831-2396 or toll-free 866-352-7108. In case you have moved the printer around recently or if you installed a replacement fuser recently -- Here are instructions for checking those fuser tabs on your LaserJet 4000, 4100, 4200, 4300, 4250, 4350 series fuser: Turn your printer off and remove your fuser. Flip it to the gear side (the left side) and press inwards on the fuser tab to make sure it is fully clicked in place, as shown below. Then flip the fuser over to the right side (the non-gear side) and press in on the other fuser tab to make sure it is also fully clicked in place. (right side of a LaserJet 4000/4050 fuser pictured below) (right side of a LaserJet 4100 fuser pictured below) After pressing in on the tabs, re-install the fuser and test. If the '50.2' error continues, replace the fuser. Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance cou
a 50.2 error. Unit has been sitting un-plugged. Thats not an issue. Most past models sent me directly to AC PS next. Does anyone recommend any 50.2 fuser error p3015 other part to check? Respond to this 0 First make sure it is the 50.2 fuser error hp 5100 correct fuser for that printer. The 4200 fuser only works in a 4200 not like the 4250 which also works 50.1 fuser error in the 4350. That said if the fuser is the correct one with the correct voltage, the next item would be the dc controller followed by the low voltage power supply. by dmzcompute on http://www.printertechs.com/printer-troubleshooting/11-50-2-fuser-error Dec 6, 2006 at 4:27pm Add comment Please sign in to comment 0 Wondering if you got this one figured out?I too have a 4200 showing the 50.2 error. Replaced the fuser and other parts from maintenance kit. The new fuser specifically has a "4200" sticker on it along with the part number: PM1-0013 / 110V. The part number is verified. The error persisted so I changed the http://www.fixyourownprinter.com/posts/43061 DC Controller PCA. No joy, same error. Now I just changed the Power Supply and it still has the same error message, 50.2. The fuser is cold. The fuser connects directly to the power supply so both connectors and any inter-unit wiring have been changed out. by sstuart on Dec 26, 2006 at 11:29am Add comment Please sign in to comment I have seen alreasy about a dozen printers where the wrong fuser has been installed. If you have another 4200 fuser even if the teflon is bad just try anyway to see if the message goes away. - dmzcompute Am still having the same error,so what else can I do to resolve the problem? - Anonymous can you send vido that you maintain this fuser error or to change this fuser.thanks - Anonymous 0 Ohm out the fusers.http://www.partsnow.com/service_today/4200.aspLikely you have two bad ones. by Stephen on Dec 26, 2006 at 11:48am Add comment Please sign in to comment 0 I have two hp 4250 printers having the same problems. I have tried a known good fuser pulled out of a working 4250 and got the same problem. I noticed I do not hear the fuser spin up when the printer is t
Copier and Fax Repair 260-417-4807 Brother Tech ArticlesCanon Tech ArticlesCopyStar Tech ArticlesDell Tech ArticlesHP Tech ArticlesKyocera Tech ArticlesLexmark Tech ArticlesOkidata Tech ArticlesSamsung Tech ArticlesXerox Phaser Tech Articles HP 4240, 4250, 4350 Laserjet 50.2 Fuser Error Warm-up Issues 4200 / 4240 / 4250 / 4300 http://www.fortwayneprinterrepair.com/wordpress/2011/10/17/hp-4240-4250-4350-laserjet-50-2-fuser-error-message/ / 4350, HP Tech Articles Add commentsOct 172011 HP Laserjet 4240, 4250, 4350 50.2 fuser error Warm-up IssuesIf the HP laserjet 4240, 4250, and 4350 printers have a fuser warmup service problem then the 50.2 fuser error is displayed on the control panel. Several situations can result in this error. In this article I will walk you through several of the problems that can cause this error and explain what steps can be taken to try and clear the fuser error 50.2 error without the need to replace the fusing assembly. HP LaserJet 4240, 4250, 4350, RM1-1082, Fuser AssemblyTroubleshooting The HP Laserjet 4240, 4250, 4350 50.2 fuser error1. If you were to call HP or any service company they would recommend checking the power source. These machines handle a large amount of power. They should be plugged straight into a wall outlet and not a power strip or battery backup. I know what some of you are thinking. It has worked for 50.2 fuser error years like this I don't need to change it. Do with the information what you want. I've seen power issues cause problems like this before so I would advice doing it.2. If you just replaced the fuser check and make sure you ordered the right one and type. There are several different types of 4000 fusers that can be installed in this machine and will not work. Also there is a 220v and a 120v fuser. Given the several options it is easy to purchase the wrong one or the vendor to accidently ship you one that has the wrong heating element installed in it and it will result in a 50.2 fuser error. Happen to me twice, by the way.3. Is just the fusers age. Inside the fuser is a fuser film and heating element. Overtime the heating element starts to ware out and get scratches in it. This causes the machines to take longer to warm up which can result in this error. Conclusion About the HP Laserjet 4240, 4250, 4350, 50.2 Fuser ErrorFinal thing to try is to turn the machine off, unplug it, and let it sit for 10 to 20 minutes and remove and reseat the fuser unit. This allows the machine to clear out its memory and when the machine next starts it will go through its normal power up sequence. If this doesn't resolve the 50.2 fuser error in your HP lase