Clear 925 Fuser Error
Contents |
5310n, printers Perform a power on reset of the printer. Turn the printer off. Disconnect the power and data cables from the printer. Wait at least five seconds. Reconnect the power and data cables of the printer. 50.3 fuser error Turn the printer on. Ensure that the correct power requirements for laser printer are met.
50.5 Fuser Error
Always review the Owner's Manual of the Laser printer to determine the maximum wattage of the printer while printing. Always try to plug the 50.4 fuser error laser printer directly to a wall outlet. Avoid plugging the laser printer into a power strip shared by other devices. Ensure that other outlets on the same circuit do not have “high power demand” devices in operation. Usually, one http://support.lexmark.com/index?page=content&segment=SUPPORT&locale=en&userlocale=EN&id=SO5058&productCode=LEXMARK_T656 circuit breaker provides power to several outlets. NEVER plug a laser printer into an Uninterruptible Power Supply (UPS) system. The power demands of a laser printer are usually not compatible with the capabilities of small home and business UPS systems. Download and install updated firmware for Dell 5210n/5310n laser printer. Verify if the paper size and type settings in the operator panel matches the print media size and type being used on the printer. Press the Menu button. Press http://www.dell.com/support/article/us/en/04/SLN162455 the Select button to select Paper Menu. Press the down arrow until Paper Size/Type appears and press Select. Press the down arrow until the specified tray appears. Then press the Select button. Open the paper tray. Verify the paper stop slider is set to the same paper size as the operator panel. Press the Select button. Verify the paper type in the tray is the same as the paper type in the operator panel. Determine if the fuser has been replaced for this issue. The fuser has not been replaced: Replace the Please contact Dell Technical Support for further advice. The fuser has been replaced: Please contact Dell Technical Support for further advice. Quick Tips content is self-published by the Dell Support Professionals who resolve issues daily. In order to achieve a speedy publication, Quick Tips may represent only partial solutions or work-arounds that are still in development or pending further proof of successfully resolving an issue. As such Quick Tips have not been reviewed, validated or approved by Dell and should be used with appropriate caution. Dell shall not be liable for any loss, including but not limited to loss of data, loss of profit or loss of revenue, which customers may incur by following any procedure or advice set out in the Quick Tips. Article ID: SLN162455 Last Date Modified: 07/29/2013 12:00 AM Rate this article Accurate Useful Easy to understand Was this
E460, X264, X363 Fuser and Heat Errors (920 - 925) iteminc SubscribeSubscribedUnsubscribe681681 Loading... Loading... Working... Add to Want to watch this again later? Sign in to add this video https://www.youtube.com/watch?v=pmDvqDrumHI to a playlist. Sign in Share More Report Need to report the http://www.printertechs.com/printer-troubleshooting/382-920-service-fuser-error-lexmark-t640-t642-t644-t650-t652-t654 video? Sign in to report inappropriate content. Sign in Transcript Statistics 89,388 views 60 Like this video? Sign in to make your opinion count. Sign in 61 2 Don't like this video? Sign in to make your opinion count. Sign in 3 Loading... Loading... Transcript The interactive fuser error transcript could not be loaded. Loading... Loading... Rating is available when the video has been rented. This feature is not available right now. Please try again later. Uploaded on Dec 2, 2011If your Lexmark E260 is flashing a fuser error, or if your Lexmarak E360, E460, X264, or X363 is displaying any error code starting with 920, 921, 922, clear 925 fuser 923, 924, or 925 you most likely need to replace the fuser, Part #: 40X5344 (110V - US & Canada). To order this part please click here.http://www.iteminc.com/itemdesc.asp?i...For any other printer needs visit us at http://www.iteminc.com Category Science & Technology License Standard YouTube License Show more Show less Loading... Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. Up next Service Printhead Error (Lexmark T650n Service Printhead Error Onarımı - VIDEO) - Duration: 29:52. Recep Kalayci 26,994 views 29:52 Lexmark E260/360/460 Photoconductor (Drum) Kit. Разборка, чистка, замена. - Duration: 16:42. vovanfun 33,637 views 16:42 Lexmark Laser Technology Presentation - Duration: 4:47. ntaradotcom 148,771 views 4:47 Lexmark E350D, Toner, Reset Fotoconduttore, Sensori, Macchia Fogli, Non prende la carta - Duration: 8:33. Sig. Wolf Risolvo Problemi 14,425 views 8:33 Lexmark Printer Training - Duration: 18:57. ramesh0356 10,083 views 18:57 Lexmark X364dn Unboxing & Setup - Duration: 18:13. Terry Wirth 18,988 views 18:13 Vídeo Recarga Toner Lexmark E260 | E360DN | E460DN - Vídeo Aula Valejet.com - Duration: 4:06. valejet TV 40,600 views 4:06 resetear foto
Account Login Shopping Cart My Account Checkout Home Troubleshooting 920 Service Fuser Error Lexmark T640 T642 T644 T650 T652 T654 Email 920 Service Fuser Error Lexmark T640 T642 T644 T650 T652 T654 If you are seeing the '920 Service Fuser' message on your Lexmark T640, T642, T644, T650, T652, or T654 series printer , you probably need to replace the fuser assembly. This error message means the fuser assembly (which bonds the toner to the paper) is unable to heat to the needed temperature for printing. A fuser is a consumable part, over the life of the printer you can expect to change a fuser several times. Fusers are sold as part of the preventative maintenance kit. Lexmark rates the life expectancy of a fuser around 150,000 pages, but a fuser can fail much earlier depending on printing conditions, paper jams, and the quality of the fuser installed. For a temporary fix, you can try turning the printer off and back on again, sometimes the reboot allows the fuser to reset so you can print a few more pages. Usually the error message returns quickly; in that case you should install a replacement fuser. Fortunately, replacing fusers on these models model is not difficult. We have installation instructions available here. Call us with any questions toll-free 866-352-7108 or local 608-831-2396. See our links to purchasing info below. Purchasing information: Lexmark T640 , T642, T644 series fuser and maintenance kitPurchasing information: Lexmark T650 , T652, T654 series fuser and maintenance kit Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations from PrinterTechsGlossary of terms Home Site Map Policies Legal Back To Top © 2016 PrinterTechs.com Inc., PrinterTechs and the PrinterTechs logo are trademarks of Printertechs.com, Inc. and may not be used without advance written permission of PrinterTechs.com, Inc.