2200d Error
Contents |
using a method Moe had once mentioned. The symptons on the machines were a bit different but the error message was the same. When you sent a print document the machine would start to warm up and then all three light would come on solid. Pressing the job cancel and go hp laserjet 2200 orange light flashing buttons at the same time would result in only the middle led staying on solid which is a
Hp Laserjet 2200d All Three Lights On
52 laser/scanner error. In both case the motor in the laser/scanner was the culprit. With the cost of a new laser/scanner being about 200.00 it is really
Hp Laserjet 2200 Service Manual
not economical to replace the part. What I did was the following. I removed the right side cover by pressing down on the button below the top cover and moving the cover towards the front and out. Next I lowered the back face up tray and
Hp Laserjet 2200 Secondary Light Pattern
released the two holding clips one on each side so the tray would go all the way down and removed the two screws which secures it to the frame. I then pulled out from the left side when looking from the rear and released the small clip on the right side and off it comes. I then removed the two screws one on each side in the back which secures the top cover. I next removed the two screws in the front under the toner door one on each side which hold hp laserjet 2200d manual the cover in the front. I then released the toner cam plastic piece on the right side which raises with the toner door. All you do is press together the plastic piece which goes thru the hole and slde the clip to the right and push it down into the down cover. Now just release the small holding clip on the left side under the toner door and you can lift the top cover off. Once the cover is off, you now have access to the laser/scanner which is the black box in the middle rear. Remove the multicolored wire on the right side from the circut board and release from the two clips on top of the laser/scanner and lay it over the left side. Now remove the purple wire connector from the same board which goes to the two wire harnesses on the laser scanner. Remove the one end of that same cable from the front right side connector on the top and release both parts of the wire from the holding clip on the top of the laser/scanner. Now remove the six black screws which hold the top of the laser/scanner cover and remove the cover. In the back of the laser/scanner is the motor assembly which the other part of the purple wire harness goes to. Remove the four screws which hold the motor and circut board and remove the motor and circut board. You may have to apply a bit of upward pressure to get it to come out, but it will come out. Now looking at the chrome motor cover at the bottom is a small plast
General Printing Problemspage 84................................................................................................................................................................ Troubleshooting Control Panel Messagespage 104................................................................................................................................................................ Troubleshooting PostScript (PS) Errorspage 121................................................................................................................................................................ Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Manuals Brands HP Manuals Printer 2200 - LaserJet B/W Laser Printer User manual HP LaserJet 2200 User Manual: Secondary hp laserjet 2200 troubleshooting Light Patterns Hewlett-packard laserjet printer user guide. Hide thumbs Also See for hp laserjet 2200 all lights on LaserJet 2200 Service manual - 324 pagesGetting started manual - 228 pagesUser manual - 172 pages hp laserjet 2100 error lights 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 http://www.fixyourownprinter.com/posts/42093 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 http://www.manualslib.com/manual/72614/Hp-Laserjet-2200.html?page=108 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 Secondary Light Patterns Note You can also use the control panel simulator to understand printer messages. Continuable Attention Errors Type of Error Memory Overflow Temporary Engine Error Print Overrun 96 Chapter 4 Problem Solving Light Pattern Recommended Action The printer memory is full. Press G to resume printing. If you lose O some data, try to free some printer memory by removing any unnecessary fonts, macros, or any data currently in printer memory. If you continue to lose data, you may need to add more
Smartphones More Software Memory Power Supplies Peripherals Displays Automotive PSUs Android Your question Get the answer Tom's Hardware>Forum>Computer Peripherals>HP LASERJET 2200 ERROR LIGHT FLASHING> HP LASERJET 2200 ERROR LIGHT FLASHING Tags: Printers Hewlett Packard Laserjet Peripherals http://www.tomshardware.com/forum/18950-3-laserjet-2200-error-light-flashing Last response: April 15, 2005 12:14 AM in Computer Peripherals Share Marty April 14, 2005 12:12:48 PM Archived from groups: comp.periphs.printers (More info?) Hi All, Having a nightware with a laserjet 2200dn. The error light is flashing all the time. The computer tells me that the printer has no paper in it but there is? I have performed cold resets on EIO, NVRAM, I have exchanged formatter board, engine controller board, registration assembley hp laserjet for paper sensor in tray 2, i have checked rechecked all connections to every component to this printer. The only option left is the main power board, this has a wire running from it to the paper sensor for tray 2, is it possible that there is no current reaching the sensor from the board even if all other part are OK? Any advice would be appreicated. Kind Regards Martin Cummins More about : hp laserjet 2200 laserjet 2200 error light flashing Anonymous a b α HP April 15, 2005 12:14:37 AM Archived from groups: comp.periphs.printers (More info?) Martin: One fo three things could cause that problem: 1). Fuser Exit Sensor is knocked out of place or the Optical Sensor at the Fuser Exit Sensor is bad. 2). Toner Cartridge is not being detected. 3). The Top Cover latch is not activating the switch. When you turn the printer on, do you hear the Motor running? Noise or no noise??? If you don't hear the motor running, most likely cause #1. Remove the Fuser assembly and check the Sensor flag arm and the sensor itself. Use compress air to clean teh Optical sensor. Dewaine Marty wrote: > Hi All, > > Having a nightware with a laserjet 2200dn. > The error light is flashing all the time. > The computer tells me that the printer has no paper in it but there is? > > I have performed cold resets on EIO, NVRAM, > > I have exchanged formatter board, engine controller board, registration > assembley for paper sensor in tray 2, i have checked rechecked all > connections to every component to this printer. > > The only option left is the main power board, this has a wire running > from it to the p