Kyocera Fs-2000d Error
Contents |
Self-diagnostic Function Hide thumbs Also See for FS-2000D Manual - 146 pagesInstallation manual - 56 pagesUser manual - 2 pages 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 kyocera fs 3900 service manual 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 kyocera fs 4000dn service manual 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 kyocera fs-3900dn manual 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 kyocera fs-2000d network setup 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 2F8/2F9/2GA-1 1-4-2 Self-diagnostic function (1) Self-diagnostic function This printer is equipped with self-diagnostic function. When a problem is detected, the printer stops printing and display an error message on the operation panel. An error message consists of a message prompting a contact to service personnel, total print count, and
Kyocera Fs 2000d Manual
a four-digit error code indicating the type of the error. (The display varies depending on the type of the error.) Call service Error code (2) Self diagnostic codes Code 0150 Engine PWB EEPROM error Detecting engine PWB EEPROM com- munication error. 0420 Paper feeder communication error Communication error between engine PWB and optional paper feeder. 1010 Lift motor lock error *35/37 and 45/47 ppm printers (EUR/ USA model) only A motor over-current signal is detected continuously for 5 seconds since the lift motor is activated. 1-4-2 6000:012345 Total print Contents Call service F000 Error code Causes Improper installa- tion engine PWB EEPROM. Defective engine PWB Improper installa- tion paper feeder. Defective harness between connect-L PWB (YC2) and paper feeder inter- face connector, or improper connec- tor insertion. Defective harness between connect-L PWB (YC6) and engine PWB (YC4), or improper connector inser- tion. Defective engine PWB. Defective paper feeder. Defective bottom plate elevation mechanism in the paper cassette. Defective lift motor drive transmission system. Defective lift motor. Replace the lift motor. Defective engine PWB. Error power off F030 Error code Remarks Check procedures/corrective measures Check the engine PWB EEPROM installa- tion, Remedy. Replace the engine PWB (See page P.1-5- 22). Follow installation instruction carefully again. Reinsert the connector. Also check for conti- nuity within the connector harness. If none, remedy or replace the harness. Reinsert the connector. Also check for conti- nuity within the connector harness. If none, remedy or replace the harness. Replace the engine PWB (See page
Copier and Fax Repair 260-417-4807 Brother Tech ArticlesCanon Tech ArticlesCopyStar Tech ArticlesDell Tech ArticlesHP Tech ArticlesKyocera Tech ArticlesLexmark Tech ArticlesOkidata Tech ArticlesSamsung Tech ArticlesXerox Phaser Tech Articles Kyocera FS2000D Error Code C6000
Kyocera Printer Cleaning Instructions
Low Temperature FS2000, Kyocera Tech Articles Add commentsMar 012015 Diagnostic Tips for kyocera fs 3900dn network setup the Kyocera FS2000D Error Code C6000 Low Temperature ProblemThe Kyocera FS2000D Error Code C6000 means that the machine has told the kyocera printer troubleshooting power supply to provide AC power to the lamp in the fuser but the fuser didn't reach the correct operating temperature in the set amount of time. When the lamp turns the hot https://www.manualslib.com/manual/772594/Kyocera-Fs-2000d.html?page=58 roller starts heating up. Once the hot roller gets to a certain temperature then the machine can start printing. Also, the machine must maintain a certain temperature while printing. Failure of either of things can result in the error code C6000. Below you will find some diagnostic tips from the service manual as well as some of my own advice. You will find links on this page to http://www.fortwayneprinterrepair.com/wordpress/2015/03/01/kyocera-fs2000d-error-code-c6000/ order in a new fusing assembly and at the bottom of the page you will find a link to the removal and replacement instructions for the fusing assembly.Kyocera FS2000D FK-310 Fuser Unit - 120 Volt Kyocera FS2000D Error Code C6000 Description Broken fuser heater lamp wire The temperature does not reach 100 °C/ 212 °F after the fuser heater lamp has been turned on continuously for 30 s. The temperature does not rise by 1 °C/ 1.8 °F after the fuser heater lamp has been turned on continuously for 5 s during printing.-- Service Manual Diagnostic Tips for the Kyocera FS2000D Error Code C6000 1. Poor contact in the fuser thermistor M connector terminals. Reinsert the connector. 2. Fuser thermistor M installed incorrectly. Check and reinstall if necessary. 3. Thermal cutout triggered. Check for continuity. If none, replace the thermal cutout. 4. Fuser heater lamp installed incorrectly. Check and reinstall if necessary. 5. Broken fuser heater lamp wire. Check for continuity. If none, replace the fuser heater lamp.Additional Diagnostic TipsThe main thing I want to know when I get an error like this, is if the lamp is turning on. I'm not sure on these machines but on some machines the lam
fuser unit. I have taken the fuser units out of both and run a continuity test on both lamps; one ok kyocera fs 3900 the other not. I used the "good" lamp in the other fuser, but I'm still gettng the error. Any suggestions would be helpful and does anyone know a supplier where I can buy these lamps? Thanks. Respond to this Please sign in to comment Unknown Printer Buy discount ink Buy this printer © Copyright 2011-2016, FixYourOwnPrinter.com, Inc. Privacy Policy Terms of Use
appreciated. Respond to this Please sign in to comment Unknown Printer Buy discount ink Buy this printer © Copyright 2011-2016, FixYourOwnPrinter.com, Inc. Privacy Policy Terms of Use