Line Error Sending Fax

entirety, is "line error", but

Fax Line Busy Signal

I think that sums it up nicely.) Getting why is my fax line busy a line error notification while sending or receiving a fax is annoying, but

Phone Line Error Fax Machine

it many cases it’s a simple problem to fix. You may need to haul out your machine’s user manual to line error sharp fax machine do it most efficiently, though. The line error needs to be “cleared.” If the instructions in your manual don’t work, or you can’t find the manual, try unplugging the fax machine at the power outlet. Don’t plug it back in fax machine troubleshooting right away – wait a minute or so. It’s also quite possible, if you’re getting a line error or “comm” (communication) error, that there’s something wrong with your telephone line. Use your regular phone to test for that. It could be the cord, the jack, “line noise,” the need to dial a special number to get an outside phone line, a VoIP issue (if you have that type of service), or any number of things. Do you have a question about faxing? Send me your fax question. This entry is filed under Fax Broadcasting, Fax Machines, Fax Modems, Fax Servers, Internet Fax Services, Other Communications, VOIP. Fax Answers is Copyright 2005-2016 by Savetz Publishing, Inc. Privacy Policy. Friends. Entries (RSS)

be down. Please try the request again. Your cache administrator is webmaster. Generated Thu, 20 Oct 2016 05:51:07 GMT by s_wx1202 (squid/3.5.20)

up the printer to fax Faxing FAQFax troubleshooting checklistIf you encounter problems sending and receiving faxes, then check the connection first:Check for a dial tone on the telephone line http://www.lexmark.com/publications/pdfs/2007/s51x/html/en/fax-troubleshooting-checklist-topic.html by plugging an analog telephone into the wall jack, DSL filter, VoIP device, or cable modem where you connected the printer. Make sure you plug the telephone into the same http://siica.sharpusa.com/portals/0/downloads/Manuals/MX-6240N-7040N/contents/09-006.htm port.If you do not hear a dial tone, then contact your line provider.While the printer is connected to the telephone line, check for a dial tone by plugging an analog telephone line error into the port of the printer.If you do not hear a dial tone, then use the checklist below. Listen for a dial tone after checking each item.If you hear a dial tone but still have problems sending and receiving faxes, then see the other topics in this section.Connection checklistMake sure that the printer and other devices on the line (if applicable) are fax line busy set up and configured correctly according to your setup scenario.Make sure that the cables are connected to the correct ports.Make sure that the cables are securely plugged in.Check the cable connections for the following hardware, if applicable:Power supplyAnswering machineCable modemSplitterTelephoneVoIP adapterDSL filterRJ-11 adapterIf the printer is connected to a Digital Subscriber Line, then make sure you are using a DSL filter for the printer.If the printer is connected to a VoIP adapter or cable modem, then make sure that the printer is plugged into the first phone port.If you are using a splitter, then make sure that you are using a phone splitter. Do not use a line splitter.Cannot send faxesIf the "Fax troubleshooting checklist" does not solve the problem, then try one or more of the following:Make sure that you have registered your user information in the printerIf you did not enter your user information during initial setup, then enter your fax name and fax number. In some countries, you cannot send a fax without entering your fax name or company name. Some fax machines also block unknown faxes or faxes wit

the ""position. After the main power indicator changes from flashing green to the lit up state, press the [POWER] button. When the background color of the job status display at the upper right corner of the touch panel is not gray, do not switch off the main power switch or unplug the power plug. This may damage the hard drive or cause the data being stored or received to be lost. Problem Point to check Solution TRANSMISSION DOES NOT TAKE PLACE Is the telephone line connected securely? Check the telephone line jack, the wall jack, and any extension adapters to make sure that all connections are secure. SIDE AND BACK Is the correct type set for the telephone line? Check your administrator whether the telephone line is set properly. From "Dial Mode Setting" in setting mode (administrator), select the type of telephone line. => "Setting mode (administrator)" → [System Settings] → [Image Send Settings] → [Fax Settings] → [Default Settings] → [Dial Mode Setting] Is a busy signal received? If a busy signal is received, the transmission is temporarily canceled and then automatically attempted again after a brief interval. (Factory default setting: 2 attempts, 3 min. intervals) => "Setting mode (administrator)" → [System Settings] → [Image Send Settings] → [Fax Settings] → [Send Settings] → [Recall in Case of Line Busy] . To cancel the transmission, tap the job status display on the operation panel, tap the key of the print job that you wish to delete, and tap the [Stop/Delete] key. A message will appear to confirm the cancelation. Tap the [Cancel] key. Did a communication error occur? If an error occurs that prevents transmission, the transmission is temporarily canceled and then automatically re-attempted after a brief interval. (Factory default setting: 2 attempts, 3 min. intervals) => "Setting mode (administrator)" → [System Settings] → [Image Send Settings] → [Fax Settings] → [Send Settings] → [Recall in Case of Communication Error] . To cancel the transmission, tap the job status display on the operation panel, tap the key of the print job that you wish to delete, and tap the [Stop/Delete] key. A message will appear to confirm the cancelation. Tap the [Cancel] key. The machine supports error correction mode (ECM) and is configured to automatically resend any part of a fax that is distorted due to noise on the