Post Error 0078
Finding »Contact Technical Support »Webmaster Mailbox »Repair / RMA FAQ If you are fully aware of the category of your question, you may choose one of the categories below for frequently asked questions.Catalogue: General FAQ, HDD FAQ, VGA FAQ, Audio FAQ. Keyword: Question (Q&A-47|185): During the POST, there is a number "0075" or "0078" showed at the right corner of the screen, and the system stop for a long time. What can I do?(10/20/2006) Answer:The problem may be caused by incorrect jumper settings or bad cables of your IDE or SATA devices. Please refer to following steps to check your system. For IDE devices: 1.If you connect 2 IDE devices to 1 IDE cable, please double check the jumpers of your IDE devices if they were set correctly. The device which is connected to the black connector should be set as master, and the other should be set as slave (gray connector). 2.Please exchange the devices of master and slave on the IDE cable. 3.Please replace the IDE cable by a new one. 4.Please replace the IDE hard drive by a new one. For SATA devices: 1.Please adjust the jumpers of your SATA2 (3.0 Gb/s) hard disk drive as SATA1 (1.5 Gb/s) mode if your motherboard supports SATA1 (1.5 Gb/s) mode only. 2.Please replace the SATA cable by a new one. 3.Please replace the SATA hard drive by a new one. © 2002-2016 ASRock Inc. All rights reserved. | Information published on ASRock.com is subject to change without notice.The picture of the user interface above is a sample for reference. The actual user interface may vary due to updated software versions.
troubleshooting > ASRock (AMD Boards) AsRock 939Dual SATA2 Post Error 0078 User Name Remember Me? Password Register FAQ Members List Calendar ASRock (AMD Boards) Support forum for ASRock products. This channel is for AMD boards. Go to Page... Click here to resend forum activation email Lost your password, Request it here Future MRT MAP has MOVED here. Click here. SHARE AsRock 939Dual SATA2 Post Error 0078 ASRock (AMD Boards) Thread Tools #1 13-09-2007, 11:45 PM ChillyWilly Rookie Join http://www.asrock.com/support/faq.asp?id=185 Date: Apr 2007 Location: USA Posts: 5 Potenza rep: 0 AsRock 939Dual SATA2 Post Error 0078 Hello All, I have read a few post on the subject but nothig has worked. Basically my board has been running for 2 years and today it will not boot. It starts detecting the drives and stops displaying the famous 0078 code. I have unplugged everything, all http://forums.ocworkbench.com/showthread.php?t=67349 drives, all cards, leaving the video card and Memory only. It will go through the initial post and nothing pauses and 0078 showes up. I have cleared Cmos numerous times and removed the battey also and nothing. canot enter setup or do anything. Any Ideas, is my firmware or boards messed up? Any info would be helpfull, even if somebody had the same issue and how they resolved, even if that means replacing te board. Thanks, ChillyWilly View Public Profile Send a private message to ChillyWilly Find all posts by ChillyWilly #2 14-09-2007, 04:51 AM corvus Member Join Date: May 2006 Location: Germany Posts: 126 Potenza rep: 11 Get an account on the AMI site to be able to download their docs(free). Aaah, here, reads: "Initializes IPL devices controlled by BIOS and option ROMs" No, i don´t know an "IPL device"... corvus View Public Profile Send a private message to corvus Find all posts by corvus #3 14-09-2007, 05:10 AM AetherBender Bronze Member Join Date: Mar 2006 Location: Atlanta Posts: 762 Potenza rep: 11 http://www.ami.com/support/doc/AMIBIOS-codes.pdf http://www.phoenix.com/NR/rdonlyres/...pecsbbs101.pdf Check out section 3. Sorry to
List Welcome Guide More BleepingComputer.com → Microsoft Windows Support → Windows XP Home and Professional Javascript Disabled Detected You currently have javascript disabled. Several functions may not work. Please re-enable javascript http://www.bleepingcomputer.com/forums/t/273065/bios-hang-unable-to-enter-bios-setup-after-running-fixmbr/ to access full functionality. BLEEPINGCOMPUTER NEEDS YOUR HELP! BleepingComputer is being sued by Enigma Software because of a negative review of SpyHunter. A case like this could easily cost hundreds of thousands of dollars. If we have ever helped you in the past, please consider helping us. To learn more and to read the lawsuit, click here. CONTRIBUTE TO OUR LEGAL DEFENSE All unused funds post error will be donated to the Electronic Frontier Foundation (EFF). If you accept cookies from this site, you will only be shown this dialog once!You can press escape or click on the X to close this box. Register a free account to unlock additional features at BleepingComputer.com Welcome to BleepingComputer, a free community where people like yourself come together to discuss and learn how to post error 0078 use their computers. Using the site is easy and fun. As a guest, you can browse and view the various discussions in the forums, but can not create a new topic or reply to an existing one unless you are logged in. Other benefits of registering an account are subscribing to topics and forums, creating a blog, and having no ads shown anywhere on the site. Click here to Register a free account now! or read our Welcome Guide to learn how to use this site. BIOS Hang, unable to enter BIOS Setup after running FIXMBR Started by MilesTeg , Nov 21 2009 08:19 PM Please log in to reply 12 replies to this topic #1 MilesTeg MilesTeg Members 15 posts OFFLINE Local time:03:38 AM Posted 21 November 2009 - 08:19 PM I had a strange set of circumstances today. I was trying to update my memory from 2 to 4g. My system would not boot with the new memory and the bios gave 3 beeps. After removing the new memory, the system would boot to XP but I had no video. I powered down and powered back up. I now ha