Hp Laserjet 4050 64 Printer Error Cycle Power
Contents |
Account Login Shopping Cart My Account Checkout Home Troubleshooting HP Error Codes Numeric Error Codes 60 and up (HP LaserJet) Email HP LaserJet Error Codes 60 and up Below are error codes for the HP LaserJet series, for codes ranging from 60 and up. Please note 68.0 permanent storage full the explanations are general descriptions for ALL LaserJets, often more detailed info will be available
Hp Printer Error Codes List
if you search for a specific error code on a specific model (e.g. "50.9 error LaserJet 3000") Have a question? Call 52.0 scanner error hp laserjet p1007 us 608-831-2396 for more information. Message on printer displayWhat it meansWhat to do 62.X PRINTER ERROR There is a problem with the printer memory. The X value refers to the location of the problem: 0 = hp printer error code list pdf Internal memory 1 to 4 = DIMM slots 1, 2, 3, or 4 1. Reseat the specified DIMM. 2. Replace the specified DIMM 64 PRINTER ERROR alternates with CYCLE POWER A scan buffer error occurred 1. Turn the printer off, and then turn the printer on. 2. Perform a cold reset. 3. If the message persists, replace the formatter or firmware DIMM. 66.XX.YY [TYPE] FAILURE alternates with CHECK CABLES AND CYCLE
Hp Printer Error 79
POWER An error occurred in an external paper-handling device. 1st X = Device number in chain 2nd X = Device type 1 Input 2 Output 3 Stapler/stacker unit YY = Device specific error Press GO to clear the message. If the message will not clear: 1. Turn the printer off, and then turn the printer on. 3. Check and reseat all cables between the printer and the specified device. 4. Reseat the external paperhandling device. 5. Replace the unit. On 5si, 8000, 8100 check the C-link hook up. Also check the external paper handling PCA 68 NVRAM ERROR CHECK SETTINGS An error occurred in the printer non-volatile memory (NVRAM) and one or more printer settings has been reset to its factory default 1. Print a configuration page and check the printer settings to determine which values have changed. 2. Hold down CANCEL JOB while turning the printer on. This will clean up the NVRAM by removing old areas that are not being used. 3. Replace the formatter. 68.X PERMANENT STORAGE ERROR alternates with CHECK SETTINGS An error occurred in the printer’s permanent storage and one or more printer settings has been reset to its factory default. Print a configuration page and check the printer settings to determine which values have changed. 68.X PER
40 41 41.x 42 43 49 50 51 52 53 54 54.1 54.4 55 56 57 57.x 57.1 57.2 57.3 57.4 58.2 58.x 59.x 60-68 60,61 62.x 63 64 66.xx.yy 68 69 70-71 72 79 80 89 If you have a Laserjet 4L, hp printer support 4P, 5P, 6P, 5L, 6L, 1000, 1100, or 1200 and you are getting a light hp warranty check error code feel free to email us for info on the code. 02 WARMING UP (>3 MIN) 1. Remove I/O cables. (Cable
Hp Support
is hooked up incorrectly or bad interface in computer.) 2. Formatter PCA malfunction. 3. DC Power Supply malfunction. 2686 Only: 1. DC Power Supply/Main motor driver malfunction. IIISi/4Si Only: 1. Defective display cable, display, or Formatter PCA. 11 PAPER http://www.printertechs.com/printer-troubleshooting/hp-error-codes/194-numeric-error-codes-60-and-up-hp-laserjet OUT 1. Paper tray empty or not seated correctly. 2. Paper Control PCA malfunction. 3. Sensor arm stuck or broken. 12 PRINTER OPEN 1. The printer door/lid is open. 2. Check DC Power Supply voltages or replace DC Power Supply. 3. DC Controller malfunction. 4. Tab missing on top cover. 5. 220V unit plugged into 110V outlet. IIISi/4Si Only: 1. Check that PS1 is blocked by the latch flag. Replace PS1 if defective. 2. Check to see if fuser http://www.mj-printers.com/repair/hpcodes.html bulb turns on. If the fuser does not turn on check SW101. 3. DC Controller PCA malfunction. 4/4M/4+/4M+ Only: 1. Plunger missing on top cover. 2. Paper Control PCA malfunction. 4V/4MV Only: 1. Front Door-open Sensor (PS402) broken or stuck. 2. Toner cartridge microswitch (SW501 on High Voltage PCA) malfunction. 3. DC Controller PCA malfunction. 12 OPEN or NO TONER or NO EP IIP/IIP+/IIIP Only: 1. Paper path door open. 2. No toner cartridge or cartridge not seated. 3. Defective fan, PS4 or PS5 4. External fuser access door not closed. 4P/5P Only: 1. Top cover open. 2. No toner cartridge. 3. Defective Interlock Switch Assembly. 4/4M/4+/4M+ Only: 1. Top cover open. 2. Defective Paper Control PCA on the Paper Feed Assembly. 4L Only: 1. The part of the top door that pushes the Plunger down is broken. 13 PAPER JAM 2686 Only: 1. Broken separation belt. 2. Paper path rollers worn? a. Check paper pickup rollers. b. Check paper feed roller. c. Check transfer guide assembly. 3. Paper pickup clutch turning more than once? a. Disassemble clutch and re-grease. Note 2686D: If one clutch needs re-greasing it is likely that they all do. 4. Bad registration sensor or bad fuser exit sensor. II, III Only: If no jam visible: 1. Replace cable, fuser to DC Controller (P/N RG1-0907-000) II, IID, III, IIID Only: 1. Obstruction in paper path. 2. Out of spec media. 3.
I recommend Atlantis Laser (770-717-8017) as a very knowledgeable and competent laser repair source. People who I have referred to http://webpages.charter.net/dperr/hp_error.htm them have always indicated that their problems were fixed in a timely manner and fairly priced. Some of the checkpoints referred to in this document require special tools or meters as well as familiarity and training on laser printers. There are LETHAL voltages inside of a laser printer and untrained personnel should refrain from doing anything other than printer error determining that the error code in question is caused by a hardware failure and cannot be cleared by an operator. Welcome visitor number since 10/17/1997 02 Warming Up (If longer than 3 minutes) Also see error code 50. 2686A/D Replace DC power supply/Main motor driver assy. II, IID Remove I/O cables. Incorrect cable hookup or bad I/O port in hp printer error computer. IIISi, 4Si Defective Display cable, defective display or formatter PCB. 4MV Remove I/O cables. Incorrect cable hookup or bad I/O port in computer. Bad component(s) 11 Paper Out (MP/PC/UC/LC/EC/LE LOAD) All printers 1. Paper tray empty or not seated correctly. 2. Paper sensor arm stuck or broken. 3. Replace paper control/sensor PCB. 4L Paper cassette is empty or missing Paper cassette not properly seated Paper out flag PS2 is broken or stuck Bad DC controller PCB 5P Tray 1 (MP) is empty Tray 2 (paper cassette) is empty 12 Printer Open All printers except IIP, IIP+, 4P Printer door open Check DC power supply voltages or replace DC power supply. Replace DC controller PCB. Tab missing on top cover. IIISi, 4Si Check that PS1 (paper sensor) is blocked by the Latch Flag. Replace PS1 if defective. Check fuser bulb turn on. If no fuser bulb turn on reset SW101 on AC power supply. Replace DC Controller PCB. LJ4, 4+ Plunger missing on top cover. Replace paper Control PCB. 4V Front door open sensor
be down. Please try the request again. Your cache administrator is webmaster. Generated Mon, 17 Oct 2016 23:02:48 GMT by s_ac15 (squid/3.5.20)