How To Reduce Random Error Physics
Contents |
of the measurement device. Random errors usually result from the experimenter's inability to take the same measurement in exactly how to reduce systematic error the same way to get exact the same number. Systematic what is systematic error in physics errors, by contrast, are reproducible inaccuracies that are consistently in the same direction. Systematic errors are
Random Error Examples Physics
often due to a problem which persists throughout the entire experiment. Note that systematic and random errors refer to problems associated with making measurements. Mistakes made
Systematic Error Calculation
in the calculations or in reading the instrument are not considered in error analysis. It is assumed that the experimenters are careful and competent! How to minimize experimental error: some examples Type of Error Example How to minimize it Random errors You measure the mass of a ring three times using the same random error calculation balance and get slightly different values: 17.46 g, 17.42 g, 17.44 g Take more data. Random errors can be evaluated through statistical analysis and can be reduced by averaging over a large number of observations. Systematic errors The cloth tape measure that you use to measure the length of an object had been stretched out from years of use. (As a result, all of your length measurements were too small.)The electronic scale you use reads 0.05 g too high for all your mass measurements (because it is improperly tared throughout your experiment). Systematic errors are difficult to detect and cannot be analyzed statistically, because all of the data is off in the same direction (either to high or too low). Spotting and correcting for systematic error takes a lot of care. How would you compensate for the incorrect results of using the stretched out tape measure? How would you correct the measurements from improperly tared scale?
of the measurement device. Random errors usually result from the experimenter's inability to take the same measurement in exactly
Instrumental Error
the same way to get exact the same number. Systematic zero error errors, by contrast, are reproducible inaccuracies that are consistently in the same direction. Systematic errors are zero error definition often due to a problem which persists throughout the entire experiment. Note that systematic and random errors refer to problems associated with making measurements. Mistakes made https://www2.southeastern.edu/Academics/Faculty/rallain/plab193/labinfo/Error_Analysis/05_Random_vs_Systematic.html in the calculations or in reading the instrument are not considered in error analysis. It is assumed that the experimenters are careful and competent! How to minimize experimental error: some examples Type of Error Example How to minimize it Random errors You measure the mass of a ring three times using the same https://www2.southeastern.edu/Academics/Faculty/rallain/plab193/labinfo/Error_Analysis/05_Random_vs_Systematic.html balance and get slightly different values: 17.46 g, 17.42 g, 17.44 g Take more data. Random errors can be evaluated through statistical analysis and can be reduced by averaging over a large number of observations. Systematic errors The cloth tape measure that you use to measure the length of an object had been stretched out from years of use. (As a result, all of your length measurements were too small.)The electronic scale you use reads 0.05 g too high for all your mass measurements (because it is improperly tared throughout your experiment). Systematic errors are difficult to detect and cannot be analyzed statistically, because all of the data is off in the same direction (either to high or too low). Spotting and correcting for systematic error takes a lot of care. How would you compensate for the incorrect results of using the stretched out tape measure? How would you correct the measurements from improperly tared scale?
or experimental values. This calculation will help you to evaluate the relevance of your results. It is helpful to know by what percent your experimental values differ from your lab partners' values, or to some established value. In most cases, http://physics.appstate.edu/undergraduate-programs/laboratory/resources/error-analysis a percent error or difference of less than 10% will be acceptable. If your comparison shows http://www.owlnet.rice.edu/~labgroup/pdf/Error_analysis.htm a difference of more than 10%, there is a great likelihood that some mistake has occurred, and you should look back over your lab to find the source of the error. These calculations are also very integral to your analysis analysis and discussion. A high percent error must be accounted for in your analysis of error, and may also indicate that the purpose of the random error lab has not been accomplished. Percent error: Percent error is used when you are comparing your result to a known or accepted value. It is the absolute value of the difference of the values divided by the accepted value, and written as a percentage. Percent difference: Percent difference is used when you are comparing your result to another experimental result. It is the absolute value of the difference of the values divided by their average, and written as a percentage. how to reduce A measurement of a physical quantity is always an approximation. The uncertainty in a measurement arises, in general, from three types of errors. Systematic errors: These are errors which affect all measurements alike, and which can be traced to an imperfectly made instrument or to the personal technique and bias of the observer. These are reproducible inaccuracies that are consistently in the same direction. Systematic errors cannot be detected or reduced by increasing the number of observations, and can be reduced by applying a correction or correction factor to compensate for the effect. Random errors: These are errors for which the causes are unknown or indeterminate, but are usually small and follow the laws of chance. Random errors can be reduced by averaging over a large number of observations. The following are some examples of systematic and random errors to consider when writing your error analysis. Incomplete definition (may be systematic or random) - One reason that it is impossible to make exact measurements is that the measurement is not always clearly defined. For example, if two different people measure the length of the same rope, they would probably get different results because each person may stretch the rope with a different tension. The best way to minimize definition errors is to carefully consider and specify the conditions that could affect the measurement. Failure to account for a factor (usually systematic) – The most challenging part of designing an ex
just how much the measured value is likely to deviate from the unknown, true, value of the quantity. The art of estimating these deviations should probably be called uncertainty analysis, but for historical reasons is referred to as error analysis. This document contains brief discussions about how errors are reported, the kinds of errors that can occur, how to estimate random errors, and how to carry error estimates into calculated results. We are not, and will not be, concerned with the “percent error” exercises common in high school, where the student is content with calculating the deviation from some allegedly authoritative number. Significant figures Whenever you make a measurement, the number of meaningful digits that you write down implies the error in the measurement. For example if you say that the length of an object is 0.428 m, you imply an uncertainty of about 0.001 m. To record this measurement as either 0.4 or 0.42819667 would imply that you only know it to 0.1 m in the first case or to 0.00000001 m in the second. You should only report as many significant figures as are consistent with the estimated error. The quantity 0.428 m is said to have three significant figures, that is, three digits that make sense in terms of the measurement. Notice that this has nothing to do with the "number of decimal places". The same measurement in centimeters would be 42.8 cm and still be a three significant figure number. The accepted convention is that only one uncertain digit is to be reported for a measurement. In the example if the estimated error is 0.02 m you would report a result of 0.43 ± 0.02 m, not 0.428 ± 0.02 m. Students frequently are confused about when to count a zero as a significant figure. The rule is: If the zero has a non-zero digit anywhere to its left, then the zero is significant, otherwise it is not. For example 5.00 has 3 significant figures; the number 0.0005 has only one significant figure, and 1.0005 has 5 significant figures. A number like 300 is not well defined. Rather one should write