Brother Unable To Print 50 Error
Contents |
Du kan ändra inställningen nedan. Learn more You're viewing YouTube in Swedish. You can change this preference below. Stäng Ja, behåll den Ångra Stäng Det här videoklippet är inte tillgängligt.
and "Machine error 30": Solution 1: Lift the scanner cover using the plastic tabs, located on the left and right side of the machine until it locks securely into the open position. Slide the
Unable To Print 50 Brother Mfc J220
print head to the middle. Check for any pieces of paper or staple , unable to print 50 brother mfc 440cn paper clip... Solution 2: Lift the scanner cover using the plastic tabs, located on the left and right side of the machine unable to print 50 brother mfc j430w until it locks securely into the open position. Slide the print head over to the right side under the cover to make sure you clean the entire encoder strip. With the lint free cloth, firmly https://www.youtube.com/watch?v=8THfCUgYCMU grab the encoder strip on both sides and rub the cloth down the strip from one end to the other (left to right then right to left) at least three times. Solution 3: the encoder strip which gives the printhead the position is out of place. You have to open the printer and reinsert the strip: For MFC-845CW: 1) Lift cover. Remove the two plastic panels covering wires. Mark down position of http://fix-your-printer.blogspot.com/2011/09/unable-to-print-50-and-unable-to-print.html cables then remove them, and remove the now-freed top scanner section entirely.2) Remove screws from top plastic shell. There's two in the back and four in the front. There's also two plastic tabs in the front that must be bent aside before you can remove the top shell.3) Gently put the encoder strip back in its plastic guide. For MFC-440CN: 1) Remove Plastic wire covers from inside printers, and release plastic stay on lower edge, tilt cover to 90 Degrees 2) make a note of where each connector goes 3) release the Ribbon and 3 Multicore cables, removing grounding screw, then remove scanner module by sliding it off the hinges at 90 degrees. 4) Remove Three Front Panel Screws, carefully leaver front panel upwards releasing front side clips. 5) Remove front panel by disconnecting ribbon and wireing on both sides. 6) Remove 6 Screws (2 on back, three at front and one middle right 7) Carefully remove speaker cable (Red Connector) and lift up plastic casing, leaving printer uncovered. 8) Re-Seat Encoder Strip. 9) Re-assemble in reverse and Hey Presto. For MFC-5680CN, MFC-5460CN: 1. Unhock the top part and the blue plastic strip that stops the top part from falling, seperate it from the machine. Undo the top part of the pl
by a Fortune 500 verification firm. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer http://www.justanswer.com/printers/2tf8b-getting-print-unable-50-error-message-cleared.html you receive. Ask Andy Your Own Question Andy, Elec & Comp pro Category: Printers http://www.pcadvisor.co.uk/forum/helproom-1/unable-print-50-brother-dcp-350c-4205221/ Satisfied Customers: 23538 Experience: 11yr exp, Comp Engg, Internet expert, Web developer, SEO 16465236 Type Your Printers Question Here... Andy is online now I am getting Print Unable 50 error message. I have cleared Resolved Question: I am getting 'Print Unable 50' error message. I have cleared paper jam and reset printer. Error will not go away unable to Submitted: 6 years ago. Category:Printers Share this conversation Expert: Andy replied6 years ago. Hello !!- How and when did this problem begun. Was there a paper jam or did you replace the ink cartridge.- When did you buy this printer and since when are you facing this issue. How often do you use printer.Andy Ask Your Own Printers Question Customer: replied6 years ago. This issuse started on Nov 20. There was a unable to print paper jam.The printer was purchased 2 -3 years agoThe printer/fax part of the unit is not used often. I mainly use the scanner. Expert: Andy replied6 years ago. Hi !!Please do this and let me know. 2-1.Disconnect the Brother machine from the poweroutlet. 2-2.Open the scanner cover by pulling up on the lower right corner of the cover. 2-3.Check the print head's position. In the example photo the print head is positioned at the left hand side of the platen area. 2-4.Gently move the print head to the center. Caution Be careful not to force the print head to move. 2-5.Examine under the print head. If anything is found, remove it. Hint Use a flashlight if necessary to check thoroughly. 2-6.Close the cover and reconnect the machine to the power outlet. Let me know-------------------------------------------------------------------------------------------------------------- If it did not help, please let me know instead of leaving a Negative Feedback.Positive Feedback and BONUS are always appreciated. Andy Ask Your Own Printers Question Customer: replied6 years ago. This was already done. It did not clear error Expert: Andy replied6 years ago. Hi !!This problem can happen because of following reasons : 1. There is some piece of paper / paper clip / sticker stuck inside printer