Adaptec Storage Manager Error
Contents |
log in with your existing support account. Username Password Forgot your username or password? Support Home Answers Ask a Question Your Account Account Overview Support History Account Settings Notifications Adaptec / ICP or maxView Storage Manager reports the RAID
Adaptec Storage Manager Default Password
has a bad stripe. What does this mean? Answer ID 14947 | Published 02/20/2007 04:45 PM adaptec storage manager download windows | Updated 05/20/2014 12:59 AM Adaptec / ICP or maxView Storage Manager marks the RAID Array with a yellow exclamation point and reports
Adaptec Storage Manager Download Linux
there is a "bad stripe". What does this mean? This information applies to the following Operating System(s): - This information is not Operating System specific What is a Bad Stripe Table (BST) entry? The BST tracks stripes across a adaptec storage manager reset password logical drive that contains invalid or incomplete data. The table is stored in an area that is reserved for configuration information on each physical disk grouped into an array that hosts one or more logical drives. There is a separate table for each logical drive. A bad stripe is essentially a stripe level RAID failure, although instead of taking the entire logical drive off-line, only the data within the stripe becomes unavailable. A bad stripe entry is then made adaptec storage manager esxi to the Bad Stripe Table and becomes a part of the array and logical drive configuration. How does a Bad Stripe Table (BST) entry occur? A BST entry can occur primarily due to one of the following scenarios: Encountering Medium Error on one of the source drives during a REBUILD operation. Encountering Medium Error on same LBA of multiple array members during Verify with fix operation. If an improper shutdown occurs on a CRITICAL array (one or more drives missing) while there are open writes. How can the occurrence of Bad Stripe Table (BST) entries be minimized? Ensure that the server is always properly shut down and powered off. Ensure that the server is properly protected from unexpected power off conditions by implementing UPS redundancy. Ensure that the server is operating within environmental specifications. Monitor the physical disk subsystem for Hard Disk errors or failures. Replace failed drives as soon as possible to minimize the time an array operates in a critical state. Ensure that hot spares are available and configured for redundant arrays. Is therea wayto fix or clear a Bad Stripe Table (BST) entry on an array once it has occurred? No, there is no procedure or tool available for clearing or repairing a bad stripe while maintaining the existing array. In the instances when a bad stripe has occurred, the data contained within that stripe is incomplete, invalid, or inc
log in with your existing support account. Username Password Forgot your username or password? Support Home Answers Ask a Question Your Account Account Overview Support History Account
Adaptec Storage Manager Rebuild Progress
Settings Notifications Adaptec Storage Manager 2.12: Agent adaptec storage manager replace failed drive Service terminated unexpectedly Answer ID 15286 | Published 01/30/2008 10:05 AM | Updated 06/24/2011 06:10 AM Adaptec Storage Manager
Adaptec Storage Manager Bad Stripes
2.12 will not load if it is installed on Windows XP SP2 or Windows Server 2003 SP1 (or later SP). The Windows event log shows the following error messages: Event http://ask.adaptec.com/app/answers/detail/a_id/14947/~/adaptec-%2F-icp-or-maxview-storage-manager-reports-the-raid-has-a-bad-stripe.- ID 7022: The AdaptecStorageManagerAgent service hung on starting Event ID 7034: The AdaptecStorageManagerAgent service terminated unexpectedly This information applies to the following Operating System(s): - Windows XP - Windows Server 2003 Note: Adaptec Storage Manager Version 2.12 is no longer the most current management software. Please visit our Support site to see if the current release of Adaptec Storage Manager (ASM) http://ask.adaptec.com/app/answers/detail/a_id/15286/~/adaptec-storage-manager-2.12%3A-agent-service-terminated-unexpectedly management software is available for your controller. To resolve the problem and continue using Adaptec Storage Manager (ASM) v2.12, the issue can be corrected by editing the registry using REGEDIT.EXE or REGEDT32.EXE. Warning: Modifying the system registry can cause system instability. Do not edit the Windows registry unless you are confident about doing so. Please go to the following location in the registry: HKEY_LOCAL_MACHINE \ SYSTEM \ CurrentControlSet \ Services \ AdaptecStorageManagerAgent Remove the quotes at the beginning and end of the following line under the string 'ImagePath': C:\Program Files\Adaptec\Adaptec Storage Manager\StorServ.exe Below is the way the data of the string will look when the problem occurs: "C:\Program Files\Adaptec\Adaptec Storage Manager\StorServ.exe" Below is how the data of the string look after the edit: C:\Program Files\Adaptec\Adaptec Storage Manager\StorServ.exe Was this answer helpful? Yes No Your rating has been submitted, please tell us how we can make this answer more useful. Email *Required Your Feedback *Required Answers others found helpful Troubleshooting maxView Storage Manager launch and login issues Storage Manager Browser Edition: I/O Manager Server Service hung on starting OnTarget: adding Management Service
Help Receive Real-Time Help Create a Freelance Project Hire for a Full Time Job Ways to Get Help Ask a Question Ask for Help Receive Real-Time Help Create a Freelance Project Hire https://www.experts-exchange.com/questions/27769604/Adaptec-Storage-Manager-reset-delete-or-rebuild-degraded-RAID.html for a Full Time Job Ways to Get Help Expand Search Submit Close Search Login Join Today Products BackProducts Gigs Live Careers Vendor Services Groups Website Testing Store Headlines Experts Exchange > Questions > Adaptec Storage Manager - reset, delete, or rebuild degraded RAID Want to Advertise Here? Solved Adaptec Storage Manager - reset, delete, or rebuild degraded RAID Posted on adaptec storage 2012-06-25 Storage Hardware Server Hardware 2 Verified Solutions 14 Comments 3,543 Views Last Modified: 2012-07-02 Hi, I have a Adaptec 2120s controller on a HP ML150 SBS2003 machine. I'm using Adaptec Storage Manager v4.3. One of the RAID 1 arrays failed but when I plugged in a spare drive (that was previously in that array) it won't rebuild. I have tried to adaptec storage manager initialise and other functions on the drive but I still can't get it to join the array. I can create a hot swap drive but that is all. The spare drive is old and had problems before so probably will fail so I would also be happy just to remove the array from RAID1 and have it as a single drive but I can't seem to do that either. The array is permanently marked as 'degraded' so I have to suppress all warnings or else the system beeps and when booting pops up with the error. I could delete the array and start again but then I would loose all data, therefore: 1) How do I assign a drive to an array (without creating a hot swap)? 2) How do I remove the 'degraded' status and convert the array into a single drive? Thanks 0 Question by:OsakaKiwi Facebook Twitter LinkedIn Google LVL 29 Active today Best Solution byRandy Downs Maybe this is related to the SMART entries you saw. If so you can disable in BIOS http://www.ehow.com/how_7248987_disable-drive-detection-hp-computer.html Power On or reboot Press the
be down. Please try the request again. Your cache administrator is webmaster. Generated Fri, 30 Sep 2016 02:22:00 GMT by s_hv996 (squid/3.5.20)