Measurement Error Propagation
Contents |
uncertainty of an answer obtained from a calculation. Every time data are measured, there is an uncertainty associated with that measurement. (Refer to guide to Measurement and Uncertainty.) If these measurements used in your calculation have some uncertainty associated with them, then the final answer will, error propagation calculator of course, have some level of uncertainty. For instance, in lab you might measure an object's
Error Propagation Physics
position at different times in order to find the object's average velocity. Since both distance and time measurements have uncertainties associated with them, those
Error Propagation Chemistry
uncertainties follow the numbers throughout the calculations and eventually affect your final answer for the velocity of that object. How would you determine the uncertainty in your calculated values? In lab, graphs are often used where LoggerPro software calculates uncertainties
Error Propagation Definition
in slope and intercept values for you. In other classes, like chemistry, there are particular ways to calculate uncertainties. In fact, since uncertainty calculations are based on statistics, there are as many different ways to determine uncertainties as there are statistical methods. The error propagation methods presented in this guide are a set of general rules that will be consistently used for all levels of physics classes in this department. In the following examples: q is the result of a error propagation average mathematical operation δ is the uncertainty associated with a measurement. For example, if you have a measurement that looks like this: m = 20.4 kg ±0.2 kg Thenq = 20.4 kg and δm = 0.2 kg First Step: Make sure that your units are consistent Make sure that you are using SI units and that they are consistent. If you are converting between unit systems, then you are probably multiplying your value by a constant. Please see the following rule on how to use constants. Logger Pro If you are using a curve fit generated by Logger Pro, please use the uncertainty associated with the parameters that Logger Pro give you. In the above linear fit, m = 0.9000 andδm = 0.05774. The uncertainty should be rounded to 0.06, which means that the slope must be rounded to the hundredths place as well: m = 0.90± 0.06 If the above values have units, don't forget to include them. Constants If an expression contains a constant, B, such that q =Bx, then: You can see the the constant B only enters the equation in that it is used to determine q. Example: F = mg = (20.4 kg)(-9.80 m/s2) = -199.92 kgm/s2 δF/F = δm/m δF/(-199.92 kgm/s2) = (0.2 kg)/(20.4 kg) δF = ±1.96 kgm/s2 δF = ±2 kgm/s2 F = -199.92 kgm/s2 ±1.96kgm/s2 With the answer rounded to 3 sig figs: F = -200 kgm/s2 ±2kgm/s2 Addition and S
or more quantities, each with their individual uncertainties, and then combine the information from these quantities in order to come up with a final result of our experiment. How can you state your answer for the combined result of these measurements and their uncertainties scientifically? The answer error propagation excel to this fairly common question depends on how the individual measurements are combined in the result. error propagation square root We will treat each case separately: Addition of measured quantities If you have measured values for the quantities X, Y, and Z, with error propagation calculus uncertainties dX, dY, and dZ, and your final result, R, is the sum or difference of these quantities, then the uncertainty dR is: Here the upper equation is an approximation that can also serve as an upper bound http://physics.appstate.edu/undergraduate-programs/laboratory/resources/error-propagation for the error. Please note that the rule is the same for addition and subtraction of quantities. Example: Suppose we have measured the starting position as x1 = 9.3+-0.2 m and the finishing position as x2 = 14.4+-0.3 m. Then the displacement is: Dx = x2-x1 = 14.4 m - 9.3 m = 5.1 m and the error in the displacement is: (0.22 + 0.32)1/2 m = 0.36 m Multiplication of measured quantities In the same way as http://lectureonline.cl.msu.edu/~mmp/labs/error/e2.htm for sums and differences, we can also state the result for the case of multiplication and division: Again the upper line is an approximation and the lower line is the exact result for independent random uncertainties in the individual variables. And again please note that for the purpose of error calculation there is no difference between multiplication and division. Example: We have measured a displacement of x = 5.1+-0.4 m during a time of t = 0.4+-0.1 s. What is the average velocity and the error in the average velocity? v = x / t = 5.1 m / 0.4 s = 12.75 m/s and the uncertainty in the velocity is: dv = |v| [ (dx/x)2 + (dt/t)2 ]1/2 = 12.75 m/s [(0.4/5.1)2 + (0.1/0.4)2]1/2 = 3.34 m/s Multiplication with a constant What if you have measured the uncertainty in an observable X, and you need to multiply it with a constant that is known exactly? What is the error then? This is easy: just multiply the error in X with the absolute value of the constant, and this will give you the error in R: If you compare this to the above rule for multiplication of two quantities, you see that this is just the special case of that rule for the uncertainty in c, dc = 0. Example: If an object is realeased from rest and is in fre
uncertainty of an answer obtained from a calculation. Every time data are measured, there is an uncertainty associated with that measurement. (Refer to guide to Measurement and Uncertainty.) If these measurements used in your calculation have some http://physics.appstate.edu/undergraduate-programs/laboratory/resources/error-propagation uncertainty associated with them, then the final answer will, of course, have some level of uncertainty. For instance, in lab you might measure an object's position at different times in order to find the object's average velocity. Since both distance and time measurements have uncertainties associated with them, those uncertainties follow the numbers throughout the calculations and eventually affect your final answer for the velocity of that object. How would you error propagation determine the uncertainty in your calculated values? In lab, graphs are often used where LoggerPro software calculates uncertainties in slope and intercept values for you. In other classes, like chemistry, there are particular ways to calculate uncertainties. In fact, since uncertainty calculations are based on statistics, there are as many different ways to determine uncertainties as there are statistical methods. The error propagation methods presented in this guide are a set measurement error propagation of general rules that will be consistently used for all levels of physics classes in this department. In the following examples: q is the result of a mathematical operation δ is the uncertainty associated with a measurement. For example, if you have a measurement that looks like this: m = 20.4 kg ±0.2 kg Thenq = 20.4 kg and δm = 0.2 kg First Step: Make sure that your units are consistent Make sure that you are using SI units and that they are consistent. If you are converting between unit systems, then you are probably multiplying your value by a constant. Please see the following rule on how to use constants. Logger Pro If you are using a curve fit generated by Logger Pro, please use the uncertainty associated with the parameters that Logger Pro give you. In the above linear fit, m = 0.9000 andδm = 0.05774. The uncertainty should be rounded to 0.06, which means that the slope must be rounded to the hundredths place as well: m = 0.90± 0.06 If the above values have units, don't forget to include them. Constants If an expression contains a constant, B, such that q =Bx, then: You can see the the constant B only enters the equation in t
be down. Please try the request again. Your cache administrator is webmaster. Generated Thu, 20 Oct 2016 11:39:08 GMT by s_wx1062 (squid/3.5.20)