Lexmark Fax Machine Error Codes
Contents |
up the printer to fax Faxing FAQFax troubleshooting checklistIf you encounter problems sending and receiving faxes, then check the connection first:Check for a dial tone on the telephone line by plugging an analog telephone into the wall jack, DSL fax error code e-713 filter, VoIP device, or cable modem where you connected the printer. Make sure you
T2 Timeout Occurred Due To Loss Of Command/response Synchronization.
plug the telephone into the same port.If you do not hear a dial tone, then contact your line provider.While the printer is
Fax Error Codes
connected to the telephone line, check for a dial tone by plugging an analog telephone into the port of the printer.If you do not hear a dial tone, then use the checklist below. Listen for a http://support.lexmark.com/index?page=content&id=SO6393 dial tone after checking each item.If you hear a dial tone but still have problems sending and receiving faxes, then see the other topics in this section.Connection checklistMake sure that the printer and other devices on the line (if applicable) are set up and configured correctly according to your setup scenario.Make sure that the cables are connected to the correct ports.Make sure that the cables are securely plugged in.Check the cable connections http://www.lexmark.com/publications/pdfs/2007/s51x/html/en/fax-troubleshooting-checklist-topic.html for the following hardware, if applicable:Power supplyAnswering machineCable modemSplitterTelephoneVoIP adapterDSL filterRJ-11 adapterIf the printer is connected to a Digital Subscriber Line, then make sure you are using a DSL filter for the printer.If the printer is connected to a VoIP adapter or cable modem, then make sure that the printer is plugged into the first phone port.If you are using a splitter, then make sure that you are using a phone splitter. Do not use a line splitter.Cannot send faxesIf the "Fax troubleshooting checklist" does not solve the problem, then try one or more of the following:Make sure that you have registered your user information in the printerIf you did not enter your user information during initial setup, then enter your fax name and fax number. In some countries, you cannot send a fax without entering your fax name or company name. Some fax machines also block unknown faxes or faxes without sender information.Decrease the transmission speed of the fax modemThe modem of the printer can transmit data at 33,600 bps. This is the maximum speed at which the printer can send and receive faxes. It is not necessary, however, to set the modem to its fastest transmission capability. The speed of the modem of the receiving fax machine must match or be gr
will also be good info for other Tech's and users as well. This list gives the Fax Transmission http://www.fixyourownprinter.com/posts/63462 error code and possible solutions.E-800 Received EOT unexpectedly from the modem in V34 mode. • If error persists disable V34 modulation scheme. E-802 Too many timeouts occurred during ECM reception. • If error persists disable ECM mode. E-803 Fax was canceled by user. • Not applicable E-804 Unexpectedly received disconnect command from remote end. • Check line quality.• Adjust Transmit fax error Level/Receive Threshold values.• Remote device could be requesting an unsupported feature. E-805 Remote fax device failed to respond to the DCS command. • Adjust Transmit Level/Receive Threshold values.• Remote device could be malfunctioning. E-808 T1 Timeout occurred when trying to establish a connection with remote fax device. • Adjust Transmit Level/Receive Threshold values. E-809 T2 Timeout occurred due to loss lexmark fax error of command/response synchronization. • Adjust Transmit Level/Receive Threshold values E-80A T5 Timeout occurred when transmitting image data to remote fax device. • Check line quality.• Adjust ‘Transmit Level’.• Select a lower ‘Max Speed’ value under Fax Send settings. E-80B Too many errors when transmitting image in ECM mode. • Check line quality.• Adjust ‘Transmit Level’.• Select a lower ‘Max Speed’ value under Fax Send settings. E-80C Remote device failed to respond to the ‘CTC’ command. • Select a lower ‘Max Speed’ value under Fax Send settings.• Adjust ‘Transmit Level’. E-80D Received too many requests from remote end to repeat the previous command sent. • Check line quality.• Adjust ‘Transmit Level’.• Check if line conditions on remote end will facilitate a good connection. E-80E Functional limitation- Remote fax device does not support G3 receive capability. • Not applicable E-811 Failed to detect a fax device at the remote end. • Verify MFD is answering to fax call and not a voice call.• Decrease value of ‘Rings To Answer’ setting. E-812 No more data rates available in V34 modulation scheme.