Lexmark Prospect Pro205 Remote Fax Error
Contents |
up the printer to fax Faxing FAQFax troubleshooting checklistIf you encounter problems sending and receiving faxes, then check the connection first:Check for a dial tone on the telephone line by plugging an analog telephone into the wall jack, DSL lexmark fax error codes filter, VoIP device, or cable modem where you connected the printer. Make sure you no analog phone line connected to modem fax is disabled plug the telephone into the same port.If you do not hear a dial tone, then contact your line provider.While the printer is lexmark error codes connected to the telephone line, check for a dial tone by plugging an analog telephone into the port of the printer.If you do not hear a dial tone, then use the checklist below. Listen for a lexmark disable fax dial tone after checking each item.If you hear a dial tone but still have problems sending and receiving faxes, then see the other topics in this section.Connection checklistMake sure that the printer and other devices on the line (if applicable) are set up and configured correctly according to your setup scenario.Make sure that the cables are connected to the correct ports.Make sure that the cables are securely plugged in.Check the cable connections
Lexmark Fax Error E-724
for the following hardware, if applicable:Power supplyAnswering machineCable modemSplitterTelephoneVoIP adapterDSL filterRJ-11 adapterIf the printer is connected to a Digital Subscriber Line, then make sure you are using a DSL filter for the printer.If the printer is connected to a VoIP adapter or cable modem, then make sure that the printer is plugged into the first phone port.If you are using a splitter, then make sure that you are using a phone splitter. Do not use a line splitter.Cannot send faxesIf the "Fax troubleshooting checklist" does not solve the problem, then try one or more of the following:Make sure that you have registered your user information in the printerIf you did not enter your user information during initial setup, then enter your fax name and fax number. In some countries, you cannot send a fax without entering your fax name or company name. Some fax machines also block unknown faxes or faxes without sender information.Decrease the transmission speed of the fax modemThe modem of the printer can transmit data at 33,600 bps. This is the maximum speed at which the printer can send and receive faxes. It is not necessary, however, to set the modem to its fastest transmission capability. The speed of the modem of the receiving fax machine must match or be g
& CopiersLexmarkXX6170 All-In-One InkJet PrinterLexmark pro 205,... Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Question about Lexmark X6170 All-In-One InkJet Printer Open Question Lexmark pro 205, remote fax error Keep getting this error even though
Lexmark Fax Error E970
I changed Doc speed, turned off error correction and scan before sending options. HELP! Posted by error code 700 error in fax transmission dohkimo on Jan 07, 2010 Want Answer 0 Clicking this will make more experts see the question and we will remind you when it fax error codes ricoh gets answered. Comment Flag More Print this page Share this page × Moderate Help this question get an answer Is this question mis-categorized or about a different product? Help this question get an answer by entering the correct category or http://www.lexmark.com/publications/pdfs/2007/s51x/html/en/fax-troubleshooting-checklist-topic.html product below. Did you mean? Yes No Cancel Update (+2 points) You can't post conmments that contain an email address. × Comment Anonymously Video Images 6 Suggested Answers Anand Kumar 2035 Answers SOURCE: Hi, Remote Fax Error being displayed As some fax machines are not capable of receiving color faxes, legal size faxes, or faxes at 200x200 dpi resolution, make sure you are sending an A4 or letter size (not legal size) page at standard resolution:Press the Black button for a http://www.fixya.com/support/t3825315-lexmark_pro_205_remote_fax_error black-and-white fax. Press the Quality button to check the selected resolution.Make sure the All-In-One has enough memory free when you want to save the scanned documents into memory before sending the fax. Please refer to the following document: Click here to link to the relevant document.Note: The scanned documents will only be saved in the memory before the whole fax is sent if the Scan Before Dial option is turned on. (This is the factory default.) Up to 50 black-and-white fax pages can be stored in memory at standard resolution when there are no pending faxes in the queue. Turn off the Scan Before Dial option by pressing the following keys on the operator panel:Press the Fax button, then press Options 15 times to get to ADVANCED FAX mode. Press Select.Press Options nine times until SCAN BEFORE DIAL appears on the LCD display.Change the setting from Yes to No using the + (right arrow) button.Press Select.Note: The Scan Before Dial option controls whether a document is scanned before a call is dialed. This parameter only applies to a mono fax that uses either 200x100 or 200x200 resolution. Higher resolution mono faxes and all color faxes are scanned after the call is dialed and the receiving machine's capabilities are known.Lower the fax transmission speed to 14400 or even 9600 bps, as some older fax machines are not capable of receiving a fax at a high speed. To do so:Press th
Add to My Manuals! Save this manual to your list of manuals Page 177 highlightspartial document or photo scans 132 poor scanned image quality 131 scan not successful 132 scanning takes too long or freezes the computer 133 Copy button 16 copy job canceling 60 copy quality, adjusting 58 copy troubleshooting scanner unit does not close 131 copying 56 adjusting quality 58 collating copies 58 enlarging an image 57 making a copy lighter or darker 58 multiple page images on one sheet 59 on both sides of the paper 59, 60 Pages per Sheet 59 photos 56 reducing an image 57 repeating an image 59 tips 56 two-sided document 57 custom-size paper printing on 38 loading into the Automatic Document Feeder (ADF) 32 loading on scanner glass 32 printing 33 scanning for editing 64 scanning using the printer control panel 61 DSL filter 71 duplex copying, automatic 59 copying, manual 60 extending drying time 48 faxing 90 printing, automatic 48 printing, manual 50 duplex printing dry time choosing a given setting 50 duplex unit 10 E Eco-Mode using 19 editing photos using printer control panel 41 emission notices 161, 162, 168, 172, 173 energy conserving 6 enlarging an image 57 entering fax user information 78 envelopes 30 loading 37 printing 37 error correction, fax setting 79 error using memory card 141 Ethernet 111 EXT port 10 extending the duplex printing dry time 50 exterior of the printer cleaning 117 e-mailing scanned documents 64 D default printer, setting 52 defaults resetting factory defaults 20 dial method, fax setting 79 dial tone checking 87 dial tone volume adjusting 88 dialing prefix 86 Dialtone button 17 Digital Subscriber Line (DSL) fax setup 71 digital telephone service fax setup 73 disabling settings timeout 18 display, printer control panel 17 distinctive ring 87 documents faxing using the computer 83 faxing using the control panel 83 F factory default settings resetting internal wireless print server 143 Index resetting to 20 failed faxes retrieving 91 fax conf