Lexmark Remote Fax Error
Contents |
up the printer to fax Faxing FAQFax troubleshooting checklistIf you encounter problems sending and receiving faxes, then check the connection first:Check for a dial tone on the telephone
Error Code 700 Error In Fax Transmission
line by plugging an analog telephone into the wall jack, DSL filter, fax error codes ricoh VoIP device, or cable modem where you connected the printer. Make sure you plug the telephone into the lexmark disable fax same port.If you do not hear a dial tone, then contact your line provider.While the printer is connected to the telephone line, check for a dial tone by plugging an analog http://support.lexmark.com/index?page=content&id=SO1994 telephone into the port of the printer.If you do not hear a dial tone, then use the checklist below. Listen for a dial tone after checking each item.If you hear a dial tone but still have problems sending and receiving faxes, then see the other topics in this section.Connection checklistMake sure that the printer and other devices on the line (if http://www.lexmark.com/publications/pdfs/2007/s51x/html/en/fax-troubleshooting-checklist-topic.html applicable) are set up and configured correctly according to your setup scenario.Make sure that the cables are connected to the correct ports.Make sure that the cables are securely plugged in.Check the cable connections for the following hardware, if applicable:Power supplyAnswering machineCable modemSplitterTelephoneVoIP adapterDSL filterRJ-11 adapterIf the printer is connected to a Digital Subscriber Line, then make sure you are using a DSL filter for the printer.If the printer is connected to a VoIP adapter or cable modem, then make sure that the printer is plugged into the first phone port.If you are using a splitter, then make sure that you are using a phone splitter. Do not use a line splitter.Cannot send faxesIf the "Fax troubleshooting checklist" does not solve the problem, then try one or more of the following:Make sure that you have registered your user information in the printerIf you did not enter your user information during initial setup, then enter your fax name and fax number. In some countries, you cannot send a fax without entering your fax name or company name. Some fax machines also block unknow
troubleshooting checklistpage 128................................................................................................................................................................ Communication with printer lost when connected to Virtual Private Network (VPN)page 144................................................................................................................................................................ Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Manuals Brands Lexmark Manuals Printer 5600 Series User manual Lexmark 5600 Series User Manual: http://www.manualslib.com/manual/92526/Lexmark-5600-Series.html?page=150 Remote Fax Error; Phone Line Busy Lexmark 5600-6600 series printer user's guide. Hide thumbs 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 fax error 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 lexmark fax error 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 4 Press the arrow buttons until Auto Fax Convert appears, and then press 5 If auto fax conversion is not set to on, press the arrow buttons until On appears, and then press Remote Fax Error These are possible solutions. Try one or more of the following: C HECK THE PHONE LINE Resend the fax. There may have been a problem with the quality of the telephone line connection. D ECREASE THE TRANSMISSION SPEED 1 From the printer control panel, press 2 Press the arrow buttons until Fax Setup appears, and then press 3 Press the arrow buttons until Dialing and Sending appears, and then press 4 Press the arrow buttons until Max Send Speed appears, and then press 5 Press the arrow buttons to select a lower transmission speed, and then press 6 Resend the fax. 7 If the problem persists, repeat step 1 through step 5 to resend the fax at successively lower transmission speeds. Note: 2400 bps is the lowest transmission speed. Notes: • The lower
be down. Please try the request again. Your cache administrator is webmaster. Generated Thu, 20 Oct 2016 05:02:12 GMT by s_wx1196 (squid/3.5.20)