Mqseries 2009 Error Code
Contents |
Problem(Abstract) MQ connection is terminating with error code 2009. Cause The connection may be broken for a number of different reasons. The 2009 return
Mqje016: Mq Queue Manager Closed Channel Immediately During Connect Closure Reason = 2009
code indicates that something prevented a successful connection to the Queue Manager. The mq 2009 error most common causes for this are the following are: 1. A firewall that is terminating the connection 2. An
Websphere Mq Error Codes
IOException that causes the socket to be closed 3. An explicit action to cause the socket to be closed by one end 4. The queue manager is offline 5. The maximum number mq error 2538 of channels allowed by the queue manager are open 6. A configuration problem in the Queue Connection Factory (QCF) Resolving the problem 1. Preventing the firewall from terminating connections: Configure the Connection Pool and Session Pool settings for the QCF that is configured in IBM WebSphere Application Server so that WebSphere can remove connections from the pool before they are dropped by the firewall. mqje001: completion code 2, reason 2019 Change the value of Min Connections to 0 and set the Unused Timeout to half the number of seconds as the firewall timeout. For example, if the firewall times out connection after 15 minutes (900 seconds), set the Unused Timeout to 450 seconds. 2. Configuring to minimize the possibility of an IOException: On a UNIX system, configure the TCP stanza of the qm.ini for the queue manager to contain this entry: KeepAlive=YES This setting causes TCP/IP to check periodically that the other end of the connection is still available. If it is not, the channel is closed. Also follow the instructions for Tuning Operating Systems in the WebSphere Application Server Information Center. These will enable the user to set the operating system configuration for TCP/IP to prevent sockets that are in use from being closed unexpectedly. For example, on Solaris, user sets the TCP_KEEPALIVE_INTERVAL setting on the WebSphere MQ machine. This should be set to be less than the firewall timeout value. If TCP_KEEPALIVE_INTERVAL is not set to be lower than the firewall timeout, then the keepalive packets will not be frequent enough to keep the connection open between W
3rd party Communication;Extensions;Adapters;Interconnect; STERLINGNFX Technote (troubleshooting) Problem(Abstract) Getting MQ Error 2009 Connection Broken error http://www-01.ibm.com/support/docview.wss?uid=swg21472342 at WebsphereMQ_commit step. Symptom BP fails to send some xml files to Websphere server. Some files send successfully and others fail at the commit step with the http://www-01.ibm.com/support/docview.wss?uid=swg21553200 same BP, same destination server, and same Queue. Error Message Error messages in WebsphereMQSuite.log: [2008-08-21 08:13:43.32] ERROR 000000000000 GLOBAL_SCOPE
RSS http://www.mqseries.net/phpBB2/viewtopic.php?t=45893&sid=0cc2788175783f0538904e476af5895e Feed - WebSphere MQ Support RSS Feed - Message Broker Support
MQSeries.net Forum Index » IBM MQ Telemetry / Low Latency Messaging / Everyplace » MQ Exception 2009 and 2019 MQ Exception 2009 and 2019 « View previous topic :: View next topic » Author Message robiijohn Posted: Mon Oct 20, 2008 5:56 pm Post subject: MQ Exception 2009 and 2019 NewbieJoined: 13 Aug 2008Posts: 7 Hi, I had been working on mq error the MDB off late and had encountered the following error while trying to send out a message from the my system to an MQ. All the connections are established when the service is brought up in Websphere. My application is hosted on WebSphere 6.1.0.11. On every incoming message to a particular queue my program consumes it and onmessage() some other message will be send to a different queue. My mqseries 2009 error program is able to consume the first message but fails to write into the other queue. I'm getting two errors, first MQ Exception 2009 and next MQ Exception 2019 I did some search on the below error which is an extract from my log created for the program. People are saying its related to some MQ problem or something external rather than my application. Its a known issue and they even have a fix in MQ for AIX but sadly couldn't find any for Windows. Anybody there who can help me by letting me know how to handle this programmatically. As far as connection objects are concerned it is not losing the object or getting null. Everything seems to ok. But rather I believe there is some problem on the physical connection between the MQ and WebSphere. I'm not sure too. But please provide me your valuable suggestions. I tried changing the WebSphere connection pool and session pool settings to Entirepool and all but no Luck! LOG EXTRACT FOR THE ISSUE -------------------------------------------------------------------------------- FINE: Time : 06/10/2008 05:43:55.921 Inside SendSyncMessage Oct 6, 2008 5:43:55 PM ejbs.MAPListenerBean FINE: Time : 06/10/2008 05:43:55.921 IP Queue Name for Request Message : UIST.ONL.RQ.SVRG1.EWSS.BW Oct 6, 2008 5:43:55 PM e