Dell Beeping Error Codes
Contents |
Beep Codes on a Dell Desktop PC This article is a guide to the various diagnostics Beep Codes used by the various Dell Desktop PCs. Table of Contents: Introduction to Beep Codes Dell Desktop Systems 1. Introduction to Beep Codes dell laptop beep codes Dell has a long tradition of building diagnostic indicators into our systems.
Dell Inspiron Beep Codes
These indicators can be really useful in helping to diagnose and resolve any issues your PC might experience
Dell Beep Codes 7
whilst starting up. I've given a guide to the various codes for each family of desktop below. If the display cannot show any errors your computer might emit a series
Dell Beep Codes 1-3-2
of beeps during start-up. 3 means 3-3-3-3...That is 3 beeps and 3 beeps and ...: Endless looping until user presses the power button to shut down the system. The delay between each beep is 300ms. The delay between each set of beeps is 3 sec, and the beep sound lasts 300ms. After each beep and each set of beeps, the BIOS dell beep codes 4 should detect if the user presses the power button, if so, BIOS will jump out from looping and execute the normal shutdown process and power system. Note: If your system also has diagnostic indicator LEDs, you will want to go to the support site to get the appropriate guide for your model. Note: If your system is giving a code that isn't listed on this guide, then please contact your local support to investigate this unknown code further. If your system is giving a listed code then please use the fault descriptions below to narrow your possible No Post troubleshooting. The No Post guide below will be useful in troubleshooting your issue further. No POST, No Power, No Video on a Dell Desktop Computer. Alternatively you can Contact Us here. Back to Top 2. Dell Desktop Systems Inspiron XPS Vostro OptiPlex Precision Back Inspiron Desktops Beep/LED Codes. Power LED Blinking/Beep Code LED/Beep Code Fault Description Fault(s) Suggested Action 1 Motherboard: BIOS ROM Failure Motherboard, covers BIOS corruption or ROM error Run the Dell Diagnostics 2 Memory No Memory (RAM) detected Troub
diagnostic LED lights and diagnostic beep codes for your Latitude 10 or Latitude 10 ST2E. Diagnostic LED Codes Diagnostic LED code communicated via the Power Button LED or agreed upon alternate LED. The Power Button LED shall blink the corresponding dell beep codes 8 LED codes for the corresponding fault condition. Example: No Memory detected, Power Button LED blinks dell xps beep codes two times followed by a pause, blinks two times, pause, etc. This pattern continues until the system is powered off. LED Code dell beep codes 2 short beeps Fault Description Suggested Remedy 1 System Board: BIOS ROM failure System board, covers BIOS corruption or ROM error 2 Memory No memory/RAM detected 3 System board failure Chipset Error Clock failure Gate A20 failure Super I/O failure http://www.dell.com/support/article/us/en/19/SLN293445 Keyboard controller failure System board failure 4 Memory Memory/RAM failure 5 Real-time clock failure Reseat the CMOS battery connection If the problem persists, possible battery failure or system board failure 6 Video BIOS Video card/chip failure 7 CPU Processor failure 8 LCD LCD failure Diagnostic Beep Codes The computer may emit a series of beeps during start-up if the display cannot show errors or problems. These series of beeps, called beep codes, identify http://www.dell.com/support/article/us/en/19/SLN290715 various problems. The delay between each beep is 300 ms, the delay between each set of beeps is 3 seconds, and the beep sound lasts 300 ms. After each beep and each set of beeps, the BIOS should detect if the user presses the power button. If so, BIOS will jump out from looping and execute the normal shutdown process and power system. Beep Code Fault Description Suggested Remedy 1 BIOS ROM checksum in progress or failure System board failure, covers BIOS corruption or ROM error 2 Memory No memory/RAM detected 3 Chipset Error (North and South bridge error, DMA/IMR/Timer error) Time-Of-Day Clock test failure Gate A20 failure Super I/O failure Keyboard controller failure System board failure 4 RAM Read/Write failure Memory/RAM failure 5 Real-time clock power fail Reseat the CMOS battery connection If the problem persists, possible battery failure or system board failure 6 Video BIOS Test Failure Video card/chip failure 7 CPU-cache test failure Processor failure 8 LCD LCD failure Click the button below to Tweet feedback or request assistance on anything in the above article. Artikel-id: SLN290715 Laatste wijzigingsdatum: 06/10/2015 09:41 AM Beoordeel dit artikel Nauwkeurig Nuttig Eenvoudig te begrijpen Was dit artikel nuttig? Ja Nee Stuur ons feedback Feedback bevat ongeldig teken, speciale tekens die niet worden geaccepteerd zijn <> () \ Feedback verzen
Eurosoft/Mylex Faraday A-Tease HP IBM Landmark Microid Research/Mr NCR Olivetti Phillips Phoenix Quadtel Supersoft Tandon Zenith Intel Motherboards: CA810E CC820 SE440BX-2 D810E2CB D810EMO D815BN D815EEA D815EPEA D820LP SE440BX SR440BX JN440BX LB440GX/L440GX N440BX/NA440BX OR840 T440BX RC440BX VC820 Dell BIOS Beep Codes Dell BIOS System Messages Dell BIOS Post Codes http://www.bioscentral.com/postcodes/dellbios.htm Dell BIOS Beep Codes: Beep Codes Possible Causes Corrective Action 1 - 2 No video card http://blog.parts-people.com/2014/06/25/dell-inspiron-15r-n5110-beep-codes-diagnostic-indicators/ detected Reseat the video card 1 - 2 - 2 - 3 BIOS ROM checksum error 1 - 3 - 1 - 1 DRAM refresh error Reseat the memory modules 1 - 3 - 1 - 3 8742 Keyboard Controller error Reseat the keyboard connector 1 - 3 - 3 - 1 Memory defective or not present Reseat the memory modules 1 - 3 beep codes - 4 - 1 RAM failure on line xxx Reseat the memory modules 1 - 3 - 4 - 3 RAM failure on data bits xxx of low byte on memory bus Reseat the memory modules 1 - 4 - 1 - 1 RAM failure on data bits xxx of high byte on memory bus Reseat the memory modules Return To Top Dell BIOS System Messages: Message Possible Cause Corrective Action nnnn Cache RAM Passed nnnn KB of system cache RAM dell beep codes has been successfully tested nnnn Extended RAM Passed nnnn KB of extended RAM has been tested nnnn Shadow RAM Passed nnnn KB of shadow RAM has been successfully tested nnnn System RAM Passed nnnn KB of system RAM has been successfully tested CD-ROM drive Identified The systems automatic drive type detection feature has identified the CD-ROM drive Diskette drive A error; Diskette drive B Error Drive A or B is present but has failed the BIOS POST Ensure that the drive is installed correctly in the chassis and detected correctly in the system setup Entering Setup The system is starting the system setup program Extended RAM Failed at offset: nnnn Extended memory is not working correctly or is not configured correctly at offset: nnnn IF you receive this message after making changes in the system setup program, enter the program and restore the original value(s) Failing bits: nnnn nnnn is a map of the bits at RAM address that failed the memory test. Each 1 in the map indicates a failed bit If you receive this message after making changes in the system setup program, enter the program and restore the original value(s) Fixed Disk n Failure; Fixed Disk Controller Failure The hard drive specified by n is not working or not configured correctly Ensure that the drive is installed correctly in the chassis and defined coracle in the system setup program Fixed Disk n Identified
Diagnose & Repair How It Works Laptop Repair Pricing DC Jack Repair Dell Refurbishing Part Installation Service Send In Your Dell Laptop Refurbished Laptops DIY + How-To Videos Technology News clear text Shop DIY Help Contact Us Home>Dell Inspiron Repair Manuals >Inspiron 15R (N5110) > Dell Inspiron 15R (N5110) Beep Codes Diagnostic In ... Dell Inspiron 15R (N5110) Beep Codes Diagnostic Indicators Created by Roscoe Dyer on June 25, 2014 PrintEmail Comments 0 How to identify beep codes: When a laptop or computer first powers on, it goes through an initial set of diagnostic tests to make sure vital components are preforming correctly. These tests are called POST or Power On Self Test. When a test fails, the user is notified via POST codes, Light codes, or Beep codes. For diagnosing Beep codes you need to: Power on the laptop or restart it if it is already on. Listen to the number of consecutive beep when the computer begins to boot. Restarting the laptop may be necessary and should not harm the laptop at this time. Dell Inspiron 15R (N5110) Beep Codes # of Beeps Description Possible Cause(s) 1 BIOS ROM checksum in progress or failure System board failure, covers BIOS corruption or ROM errors. 2 No Memory (RAM) detected Memory or Memory slot failure 3 chipset Error (North and South bridge error, DMA/IMR/Timer error) Time-Of-Day Clock test failure Gate A20 failure Super I/O chip failure Keyboard controller test failure System board failure 4 Memory read / write failure Memory failure 5 Real Time Clock (RTC) power fail CMOS battery failure 6 Video BIOS test failure Video subsystem failure 7 CPU Cache test failure Processor failure 8 LCD LCD failure Most Common Fixes: 1 Beep: Replace the motherboard / system board. 2 Beeps: Reseat the memory or replace the memory. 3 Beeps: Replace the motherboard / system board. 4 Beeps: Reseat the memory or replace the memory. 5 Beeps: Replace the CMOS battery. 6 Beeps: Reseat or replace the video card or replace the motherboard / system board. 7 Beeps: Reseat or replace the CPU. 8 Beeps: Reseat the LCD cable or replace the LCD screen. Dell Laptop Replacement Parts Needed $99.95 Dell Inspiron 15R (N5110) Motherboard System Board... $99.95 Dell Inspiron 15R (N5110) Motherboard System Board with Integrated Intel Graphics - 7GC4R Eligible for FREE Economy Shipping. Only 19 left in stock - order soon. $149.95 Dell Inspiron 15R (N5110) Motherboard System Board... $149.95 Dell Inspiron 15R (N5110) Motherboard System Board with Discrete ATI Radeon graphics - NKC7K Eligible for FREE Economy Shipping. Only 1 left in stock - order soon. $24.95 Dell Inspiron 15R (N5110) Audio / USB IO Circui