Dell Gx260 Plug And Play Configuration Error
Contents |
Join Sign in GX260T has a plug & play configuration problem Desktop Desktop computer Forums (Audio, General Hardware, dell gx260 specs Video) Get this RSS feed Home Forums Wiki Details 7 Replies optiplex gx260 specs 1 Subscriber Postedover 10 years ago Options RSS Share GX260T has a plug & play configuration problem Posted dell inspiron beep codes by PaulandJanice on 20 May 2006 3:16 GX260T will not recognize HD and gives the following message: Secondary hard drive not foundPlug & play Configuration errorPlug & play Configuration
Dell Beep Codes 1-3-2
errorPlug & play Configuration errorStrike the F1 key to continueStrike the F2 key for system utility In “device manager”, my video is a problem also. It claims there are not enough resources to run it. I tried the usuall: 1. rebooting 2. disconnecting the power to the tower and then each drive and the IDE cables to the MB. dell beep codes 5 Nothing has helped. Just to be on the safe side, I uninstalled the software that seemed to cause all this, and tried a “system restore”, but all attempts have failed. I do not remember how to re-configure the system. Does anyone have a clue as to where I should start to diagnose this problem? Thank youPaulandJanice Like 0 Reply You have posted to a forum that requires a moderator to approve posts before they are publicly available. Posted by SpeedStep on 21 May 2006 0:33 There is no such model as GX260TYou didnt say which OSPlug and play errors = cards in the bus installed that are unhappy.REMOVE ALL EXPANSION CARDS AND RESET THE NVRAM.Chipset drivers have not been installed. Report Unresolved Customer Service Issues here I do not work for Dell. I too am a user. The forum is primarily user to user, with Dell employees moderatingContact USA Technical Support Get Support on Twitter @DellCaresPro Like 0 Reply You have posted to a forum that requires a moderator to approve posts
Problems Keyboard Problems Memory Problems Mouse Problems Network Problems Power Problems Printer Problems Serial or Parallel Device Problems Sound and Speaker dell error codes lights Problems System Board Problems Video and Monitor Problems Battery Problems CAUTION:
Dell Inspiron Beep Codes 4 Beeps
There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery
Dell Optiplex 780 Beep Codes
only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. CAUTION: Before you replace the battery, see "CAUTION: http://en.community.dell.com/support-forums/desktop/f/3514/t/17897168 Safety Instructions." Replace the battery If you have to repeatedly reset time and date information after turning on the computer, or if an incorrect time or date displays during start-up, replace the battery (see "Battery"). If the battery still does not work properly, contact Dell. Beep Codes Your computer might emit a series of http://www.mss.net/Links/DellDocs/OptiGX260/UserGuide/solvprob.htm beeps that identify a problem: for example, one beep, followed by a a burst of three beeps, and then one beep (code 1-3-1) means that the computer encountered a memory problem. Try to resolve the problem Write the beep code down on the Diagnostics Checklist, and perform the action recommended in the following table. Run the Dell Diagnostics to identify a more serious cause. Contact Dell for technical assistance Code Cause Action 1-1-2Microprocessor register failureContact Dell for technical assistance. 1-1-3NVRAMRun the Dell Diagnostics. 1-1-4ROM BIOS checksum failureRun the Dell Diagnostics. 1-2-1Programmable interval timerRun the Dell Diagnostics. 1-2-2DMA initialization failureRun the Dell Diagnostics. 1-2-3DMA page register read/write failureRun the Dell Diagnostics. 1-3-1 through 2-4-4DIMMs not being properly identified or usedSee "Memory Problems." 3-1-1Slave DMA register failureRun the Dell Diagnostics. 3-1-2Master DMA register failureRun the Dell Diagnostics. 3-1-3Master interrupt mask register failureContact Dell for technical assistance. 3-1-4Slave interrupt mask register failureContact Dell for technical assistance. 3-2-2Interrupt vector loading failureContact Dell for technical assistance. 3-2-4Keybo
& play configuration error If this is your first visit, be sure to check out the FAQ by clicking the link above. You http://www.sysopt.com/showthread.php?162084-Plug-amp-play-configuration-error may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. Results 1 to 8 of 8 Thread: Plug & play configuration error Tweet Thread Tools Show Printable Version Email this Page… Subscribe to this Thread… Search Thread beep codes Advanced Search Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode 04-30-2004,01:06 AM #1 morpethmike View Profile View Forum Posts Junior Member Join Date Mar 2004 Location Morpeth England Posts 17 Plug & play configuration error I have an old dell optiplex GL5100 pentium 100 i thought i would play around with, see it it still worked dell inspiron beep it origunally had .850 hard drive so i upped it to 4.2 gig win 98/2 when i switch it on i get "Plug and Play configuration error" x 6 times then "Press F1 to continue of F2 to enter setup" I press F2 nothing seems out of place so Press F1 to continue and pc starts up ok Any Thoughts/solutions?? rgds mike Reply With Quote 04-30-2004,01:25 AM #2 BipolarBill View Profile View Forum Posts Visit Homepage Extreme Member! Join Date Oct 2000 Location Norton Noo Joisey Posts 41,506 Try updating the BIOS and clearing CMOS. There should be a jumper for the latter. MS MCP, MCSE Reply With Quote 04-30-2004,02:08 AM #3 morpethmike View Profile View Forum Posts Junior Member Join Date Mar 2004 Location Morpeth England Posts 17 Thanks for info will try and report back Thanks rgds Mike Reply With Quote 05-01-2004,02:55 AM #4 morpethmike View Profile View Forum Posts Junior Member Join Date Mar 2004 Location Morpeth England Posts 17 Hello thanks for info upgraded Bios it now works.....But new mesgg on