Error Beep Codes Dell
Contents |
Codes on a Dell Desktop PC This article is a guide to the various diagnostics Beep Codes used by the various Dell Desktop PCs. Table of Contents: Introduction to Beep Codes Dell Desktop Systems 1. Introduction to Beep Codes Dell has
Dell Beep Codes 3 Short Beeps
a long tradition of building diagnostic indicators into our systems. These indicators dell all in one beep codes can be really useful in helping to diagnose and resolve any issues your PC might experience whilst starting up.
Dell Error Beep Codes 1 3 2
I've given a guide to the various codes for each family of desktop below. If the display cannot show any errors your computer might emit a series of beeps during dell inspiron error beep codes start-up. 3 means 3-3-3-3...That is 3 beeps and 3 beeps and ...: Endless looping until user presses the power button to shut down the system. The delay between each beep is 300ms. The delay between each set of beeps is 3 sec, and the beep sound lasts 300ms. After each beep and each set of beeps, the BIOS should detect if the dell error light codes user presses the power button, if so, BIOS will jump out from looping and execute the normal shutdown process and power system. Note: If your system also has diagnostic indicator LEDs, you will want to go to the support site to get the appropriate guide for your model. Note: If your system is giving a code that isn't listed on this guide, then please contact your local support to investigate this unknown code further. If your system is giving a listed code then please use the fault descriptions below to narrow your possible No Post troubleshooting. The No Post guide below will be useful in troubleshooting your issue further. No POST, No Power, No Video on a Dell Desktop Computer. Alternatively you can Contact Us here. Back to Top 2. Dell Desktop Systems Inspiron XPS Vostro OptiPlex Precision Back Inspiron Desktops Beep/LED Codes. Power LED Blinking/Beep Code LED/Beep Code Fault Description Fault(s) Suggested Action 1 Motherboard: BIOS ROM Failure Motherboard, covers BIOS corruption or ROM error Run the Dell Diagnostics 2 Memory No Memory (RAM) detected Troubleshoot the Memory 3 Motherboard: Chipset Chipset
Vostro Beep Codes and Error Messages. This article provides information on Dell Optiplex & Vostro Beep Codes and Error Messages. Starting from the D4 generation of OptiPlex models onwards (7010/9010/9010 AIO), the beep codes will be eliminated, replaced by a single memory error pattern Now only "no memory failure" conditions generate
Beep Codes Dell Computers
the beep code, the beep pattern is 1-3-2 (1 beep, then 3 beeps, then beep codes dell optiplex 745 2 beeps). This beep code tells you that the computer encountered a memory problem. The new beep codes emit only memory
Beep Codes Dell Inspiron M5030
failure symptoms. Occasionally, reseating the memory modules may fix the beep code errors. Table of Contents: Optiplex Beep Codes Optiplex Error Messages Vostro Beep Codes Vostro Error Messages 1. OptiPlex Beep Codes The computer might emit http://www.dell.com/support/article/us/en/19/SLN293445 a series of beeps during start-up if the display cannot show errors or problems. This series of beeps, called a beep code, can be used to help identify various problems. Diagnostic Beep Codes Code Cause 1-1-2 Microprocessor register failure 1-1-3 NVRAM 1-1-4 ROM BIOS checksum failure 1-2-1 Programmable interval timer 1-2-2 DMA initialization failure 1-2-3 DMA page register read/write failure 1-3-1 through 2-4-4 DIMMs not being properly identified or used 3-1-1 Slave http://www.dell.com/support/article/us/en/19/SLN143065/EN DMA register failure 3-1-2 Master DMA register failure 3-1-3 Master interrupt mask register failure 3-1-4 Slave interrupt mask register failure 3-2-2 Interrupt vector loading failure 3-2-4 Keyboard Controller Test failure 3-3-1 NVRAM power loss 3-3-2 NVRAM configuration 3-3-4 Video Memory Test failure 3-4-1 Screen initialization failure 3-4-2 Screen retrace failure 3-4-3 Search for video ROM failure 4-2-1 No time tick 4-2-2 Shutdown failure 4-2-3 Gate A20 failure 4-2-4 Unexpected interrupt in protected mode 4-3-1 Memory failure above address 0FFFFh 4-3-3 Timer-chip counter 2 failure 4-3-4 Time-of-day clock stopped 4-4-1 Serial or parallel port test failure 4-4-2 Failure to decompress code to shadowed memory 4-4-3 Math coprocessor test failure 4-4-4 Cache test failure Please contact us for further assistance on beep codes Back to Top 3. Optiplex Error Messages An Error Message may be displayed along with the accompanying beep code. Please refer to the table below for details on the error message. Diagnostic Error Messages Error Message Indication Address mark not found The BIOS found a faulty disk sector or could not find a particular disk sector. Alert! Previous attempts at booting this system have failed at checkpoint [nnnn]. For help in resolving this problem, please note this checkpoint and contact Dell Technical Support. The computer failed to complete the boot routine
starting the remainder of the boot process. If the computer passes the POST, the computer may give a single beep (some http://www.computerhope.com/beep.htm computers may beep twice) as it starts and continue to boot. However, if the computer fails the POST, the computer will either not beep or generate a beep code that tells the user the source of the problem. If your computer has an irregular POST or a beep code not mentioned below, follow the POST troubleshooting steps beep codes to determine the failing hardware component. AMI BIOS beep codes Award BIOS beep codes Dell beep codes IBM BIOS beep codes Macintosh startup tones Phoenix BIOS beep codes Motherboard help AMI BIOS beep codes Below are the AMI BIOS Beep codes that can occur. However, because of the wide variety of different computer manufacturers with this BIOS, beep codes dell the beep codes may vary. Beep Code Descriptions 1 short DRAM refresh failure 2 short Parity circuit failure 3 short Base 64K RAM failure 4 short System timer failure 5 short Process failure 6 short Keyboard controller Gate A20 error 7 short Virtual mode exception error 8 short Display memory Read/Write test failure 9 short ROM BIOS checksum failure 10 short CMOS shutdown Read/Write error 11 short Cache Memory error 1 long, 3 short Conventional/Extended memory failure 1 long, 8 short Display/Retrace test failed two-tone siren Low CPU Fan speed, Voltage Level issue AWARD BIOS beep codes Below are Award BIOS Beep codes that can occur. However, because of the wide variety of different computer manufacturers with this BIOS, the beep codes may vary. Beep Code Description 1 long, 2 short Indicates a video error has occurred and the BIOS cannot initialize the video screen to display any additional information 1 long, 3 short Video card not detected (reseat video card) or bad video card Beeps repeating endlessly RAM problem.