Phoenix Beep Error Codes
Contents |
Eurosoft/Mylex Faraday A-Tease HP IBM Landmark Microid Research/Mr NCR Olivetti Phillips Phoenix Quadtel Supersoft Tandon Zenith Intel Motherboards: CA810E CC820 SE440BX-2 D810E2CB D810EMO D815BN D815EEA D815EPEA D820LP SE440BX SR440BX JN440BX LB440GX/L440GX N440BX/NA440BX OR840 T440BX RC440BX VC820 Phoenix ISA/MCA/EISA BIOS Beep Codes: The beep codes are
Test 51k Base Memory Error
represented in the number of beeps. E.g. 1-1-2 would mean 1 beep, a pause, 1 phoenix bios beep codes 1 long beep beep, a pause, and 2 beeps. With a Dell computer, a 1-2 beep code can also indicate that a bootable add-in card is installed phoenix award bios beep codes but no boot device is attached. For example, in you insert a Promise Ultra-66 card but do not connect a hard drive to it, you will get the beep code. I verified this with a SIIG (crap --
Asus Beep Codes
avoid like the plague) Ultra-66 card, and then confirmed the results with Dell. Submitted by John Palmer. Beeps Error Message Description 1-1-2 CPU test failure The CPU is faulty. Replace the CPU Low 1-1-2 System board select failure The motherboard is having an undetermined fault. Replace the motherboard 1-1-3 CMOS read/write error The real time clock/CMOS is faulty. Replace the CMOS if possible Low 1-1-3 Extended CMOS RAM failure The extended portion of the CMOS RAM has
Phoenix Bios Continuous Beep
failed. Replace the CMOS if possible 1-1-4 BIOS ROM checksum error The BIOS ROM has failed. Replace the BIOS or upgrade if possible 1-2-1 PIT failure The programmable interrupt timer has failed. Replace if possible 1-2-2 DMA failure The DMA controller has failed. Replace the IC if possible 1-2-3 DMA read/write failure The DMA controller has failed. Replace the IC if possible 1-3-1 RAM refresh failure The RAM refresh controller has failed 1-3-2 64KB RAM failure The test of the first 64KB RAM has failed to start 1-3-3 First 64KB RAM failure The first RAM IC has failed. Replace the IC if possible 1-3-4 First 64KB logic failure The first RAM control logic has failed 1-4-1 Address line failure The address line to the first 64KB RAM has failed 1-4-2 Parity RAM failure The first RAM IC has failed. Replace if possible 1-4-3 EISA fail-safe timer test Replace the motherboard 1-4-4 EISA NMI port 462 test Replace the motherboard 2-1-1 64KB RAM failure Bit 0; This data bit on the first RAM IC has failed. Replace the IC if possible 2-1-2 64KB RAM failure Bit 1; This data bit on the first RAM IC has failed. Replace the IC if possible 2-1-3 64KB RAM failure Bit 2; This data bit on the first RAM IC has failed. Replace the IC if possible 2-1-4 64KB RAM failure Bit 3
Macs iPad iPhone Internet & Network Digital Cameras Home Theater Getting More Help Buy Buying Guides Product Reviews Software & Apps gigabyte beep codes Do More Web & Search Social Media Gaming New & Next
Hp Beep Codes
Fix Windows PhoenixBIOS Beep Code Troubleshooting Fixes for Specific Phoenix Beep Code Errors Share intel beep codes Pin Email Windows Symptoms Basics Maintenance Error Messages by Tim Fisher Updated September 04, 2016 PhoenixBIOS is a kind of BIOS manufactured by Phoenix Technologies. A majority of http://www.bioscentral.com/beepcodes/phoenixbeep.htm modern motherboard manufacturers have integrated Phoenix Technologies' PhoenixBIOS into their systems.Several custom implementations of the PhoenixBIOS system exist in many popular motherboards. The beep codes from a Phoenix-based BIOS may be exactly the same as the true Phoenix beep codes below or they may vary. You can always check your motherboard manual to be sure.Note: http://pcsupport.about.com/od/fixtheproblem/tp/phoenix-beep-codes.htm PhoenixBIOS beep codes are short, sound in quick succession, and usually sound immediately after powering on the PC. 1 Beep Laura Harker/EyeEm/Getty Images A single beep from a Phoenix based BIOS is actually an "all systems clear" notification. Technically, it's an indication that the Power On Self Test is complete. No troubleshooting necessary! 1 Continuous Beep One continuous beep isn't an officially listed Phoenix beep code but I know of several instances of this occurring. In at least one case, the solution was to reseat the CPU. 1 Short Beep, 1 Long Beep One short beep followed by one long beep also isn't an officially listed Phoenix beep code but two readers have let me know about this one. In both cases, the problem was bad RAM which replacing obviously solved. 1 Long Beep, 2 Short Beeps One long beep followed by two short beeps indicates that there has been a checksum error. This means that there is some kind of motherboard iss
Home Page Beep Codes, Phoenix BIOS beep codes Phoenix BIOS beep codesPhoenix beep codes are the most detailed about. They use a system of 4 beeps each separated by a small pause i.e. 1 pause http://www.comptechdoc.org/hardware/beepcodes/3.htm 2 pause 1 pause 1 pause (1-2-1-1), you may need to reboot the pc http://www.helpwithpcs.com/upgrading/post-beep-codes.htm a few times in order to count all the beeps. To find out more information on Phoenix beep codes you can go here. Beep Code Description / What to Check 1-1-1-3 Verify Real Mode. 1-1-2-1 Get CPU type. 1-1-2-3 Initialize system hardware. 1-1-3-1 Initialize chipset registers with initial POST values. 1-1-3-2 Set in POST flag. 1-1-3-3 Initialize beep codes CPU registers. 1-1-4-1 Initialize cache to initial POST values. 1-1-4-3 Initialize I/O. 1-2-1-1 Initialize Power Management. 1-2-1-2 Load alternate registers with initial POST values. 1-2-1-3 Jump to UserPatch0. 1-2-2-1 Initialize keyboard controller. 1-2-2-3 BIOS ROM checksum. 1-2-3-1 8254 timer initialization. 1-2-3-3 8237 DMA controller initialization. 1-2-4-1 Reset Programmable Interrupt Controller. 1-3-1-1 Test DRAM refresh. 1-3-1-3 Test 8742 Keyboard Controller. 1-3-2-1 Set ES segment to register to 4 GB. 1-3-3-1 28 Autosize bios beep codes DRAM. 1-3-3-3 Clear 512K base RAM. 1-3-4-1 Test 512 base address lines. 1-3-4-3 Test 512K base memory. 1-4-1-3 Test CPU bus-clock frequency. 1-4-2-4 Reinitialize the chipset. 1-4-3-1 Shadow system BIOS ROM. 1-4-3-2 Reinitialize the cache. 1-4-3-3 Autosize cache. 1-4-4-1 Configure advanced chipset registers. 1-4-4-2 Load alternate registers with CMOS values. 2-1-1-1 Set Initial CPU speed. 2-1-1-3 Initialize interrupt vectors. 2-1-2-1 Initialize BIOS interrupts. 2-1-2-3 Check ROM copyright notice. 2-1-2-4 Initialize manager for PCI Options ROMs. 2-1-3-1 Check video configuration against CMOS. 2-1-3-2 Initialize PCI bus and devices. 2-1-3-3 Initialize all video adapters in system. 2-1-4-1 Shadow video BIOS ROM. 2-1-4-3 Display copyright notice. 2-2-1-1 Display CPU type and speed. 2-2-1-3 Test keyboard. 2-2-2-1 Set key click if enabled. 2-2-2-3 56 Enable keyboard. 2-2-3-1 Test for unexpected interrupts. 2-2-3-3 Display prompt "Press F2 to enter SETUP". 2-2-4-1 Test RAM between 512 and 640k. 2-3-1-1 Test expanded memory. 2-3-1-3 Test extended memory address lines. 2-3-2-1 Jump to UserPatch1. 2-3-2-3 Configure advanced cache registers. 2-3-3-1 Enable external and CPU caches. 2-3-3-3 Display external cache size. 2-3-4-1 Display shadow message. 2-3-4-3 Display non-disposable segments. 2-4-1-1 Display error messages. 2-4-1-3 Check for configuration errors. 2-4-2-1 Test real-time clock. 2-4-2-3 Check for keyboard errors 2-4-4-1 Set up hardware interrupts vectors. 2-4-4-3 Test coprocessor if present. 3-1-1-1 Disable
is first switched on or reset, it performs a special diagnostic test called a POST (Power-On Self Test). To check all of the components in the PC, the POST program sends out a signal to each device initialising each device's built-in self-test procedure. advertisement The POST test is a two stage process, first it will check all of the basic components including amongst other things, the system clock, the processor, RAM, the keyboard controller and the video card. When a device fails the first part of the POST the BIOS will send a series of beeps from the PC's speaker (internal) to inform the PC user that there is a problem. These beeps are coded allowing the user to diagnose the troublesome component. After the video has been tested successfully the BIOS will then display any errors encountered on the screen. The error message will be either a numeric code or a text message. When the POST has been completed successfully the PC will make a short beep to let the user know everything is as it should be. Below are some common beep codes for AMI and Phoenix BIOS. AMI BIOS error beep codes 1 Beep - Memory Refresh Failure (check memory) 2 Beeps - Memory Parity Error in first 64KB block (check memory) 3 Beeps - Memory Read/Write Error in first 64KB block (check memory) 4 Beeps - Motherboard timer not functioning (possible motherboard replacement) 5 Beeps - Processor Error (may need replacement Processor) 6 Beeps - Gate A20/keyboard controller failure (possible motherboard replacement) 7 Beeps - Processor Exception Interrupt Error (may need replacement Processor) 8 Beeps - Display Memory Read/Write Failure (reseat or replace video card) 9 Beeps - ROM checksum Error (replace BIOS chip or motherboard) 10 Beeps - CMOS shutdown Read/Write error (possible motherboard replacement) 11 Beeps - Bad Cache Memory - test failed (replace cache memory) Phoenix BIOS error beep codes Phoenix BIOS beep codes are a series of beeps separated by a pause, for example: beep --- beep beep --- beep --- beep beep would be 1-2-1-2 1-1-4-1 - Cache Error (level 2) 1-2-2-3 - BIOS ROM Checksum 1-3-1-1 - DRAM Refresh Test 1-3-1-3 - Keyboard controller test 1-3-4-1 - RAM Failure on address line xxxx (check memory) 1-3-4-3 - RAM Failure on data bits xxxx o