Phoenix Bios Error Codes Beeps
Contents |
Eurosoft/Mylex Faraday A-Tease HP IBM Landmark Microid Research/Mr NCR Olivetti Phillips Phoenix Quadtel Supersoft Tandon Zenith Intel Motherboards: CA810E CC820 SE440BX-2 D810E2CB D810EMO D815BN D815EEA D815EPEA D820LP SE440BX SR440BX JN440BX LB440GX/L440GX N440BX/NA440BX OR840 T440BX RC440BX VC820 phoenix bios beep codes 1-3-4-3 Phoenix ISA/MCA/EISA BIOS Beep Codes: The beep codes are represented in the number of
Phoenix Bios Beep Codes 1 Long Beep
beeps. E.g. 1-1-2 would mean 1 beep, a pause, 1 beep, a pause, and 2 beeps. With a Dell computer, phoenix award bios beep codes a 1-2 beep code can also indicate that a bootable add-in card is installed but no boot device is attached. For example, in you insert a Promise Ultra-66 card but do not connect a hard test 51k base memory error drive to it, you will get the beep code. I verified this with a SIIG (crap -- avoid like the plague) Ultra-66 card, and then confirmed the results with Dell. Submitted by John Palmer. Beeps Error Message Description 1-1-2 CPU test failure The CPU is faulty. Replace the CPU Low 1-1-2 System board select failure The motherboard is having an undetermined fault. Replace the motherboard 1-1-3 CMOS read/write error
Phoenix Bios Continuous Beep
The real time clock/CMOS is faulty. Replace the CMOS if possible Low 1-1-3 Extended CMOS RAM failure The extended portion of the CMOS RAM has failed. Replace the CMOS if possible 1-1-4 BIOS ROM checksum error The BIOS ROM has failed. Replace the BIOS or upgrade if possible 1-2-1 PIT failure The programmable interrupt timer has failed. Replace if possible 1-2-2 DMA failure The DMA controller has failed. Replace the IC if possible 1-2-3 DMA read/write failure The DMA controller has failed. Replace the IC if possible 1-3-1 RAM refresh failure The RAM refresh controller has failed 1-3-2 64KB RAM failure The test of the first 64KB RAM has failed to start 1-3-3 First 64KB RAM failure The first RAM IC has failed. Replace the IC if possible 1-3-4 First 64KB logic failure The first RAM control logic has failed 1-4-1 Address line failure The address line to the first 64KB RAM has failed 1-4-2 Parity RAM failure The first RAM IC has failed. Replace if possible 1-4-3 EISA fail-safe timer test Replace the motherboard 1-4-4 EISA NMI port 462 test Replace the motherboard 2-1-1 64KB RAM failure Bit 0; This data bit on the first RAM IC has fai
Macs iPad iPhone Internet & Network Digital Cameras Home Theater Getting More Help Buy Buying Guides Product Reviews Software & Apps Do More Web & Search Social Media Gaming New & Next Fix Windows PhoenixBIOS Beep Code Troubleshooting Fixes ibm bios beep codes for Specific Phoenix Beep Code Errors Share Pin Email Windows Symptoms Basics Maintenance Error Messages phoenix bios beep codes 1-1-1-1 by Tim Fisher Updated September 04, 2016 PhoenixBIOS is a kind of BIOS manufactured by Phoenix Technologies. A majority of modern motherboard
Asus Beep Codes
manufacturers have integrated Phoenix Technologies' PhoenixBIOS into their systems.Several custom implementations of the PhoenixBIOS system exist in many popular motherboards. The beep codes from a Phoenix-based BIOS may be exactly the same as the true Phoenix beep http://www.bioscentral.com/beepcodes/phoenixbeep.htm codes below or they may vary. You can always check your motherboard manual to be sure.Note: PhoenixBIOS beep codes are short, sound in quick succession, and usually sound immediately after powering on the PC. 1 Beep Laura Harker/EyeEm/Getty Images A single beep from a Phoenix based BIOS is actually an "all systems clear" notification. Technically, it's an indication that the Power On Self Test is complete. No troubleshooting necessary! 1 Continuous Beep One continuous beep http://pcsupport.about.com/od/fixtheproblem/tp/phoenix-beep-codes.htm isn't an officially listed Phoenix beep code but I know of several instances of this occurring. In at least one case, the solution was to reseat the CPU. 1 Short Beep, 1 Long Beep One short beep followed by one long beep also isn't an officially listed Phoenix beep code but two readers have let me know about this one. In both cases, the problem was bad RAM which replacing obviously solved. 1 Long Beep, 2 Short Beeps One long beep followed by two short beeps indicates that there has been a checksum error. This means that there is some kind of motherboard issue. Replacing the motherboard should fix this problem. 1-1-1-1 Beep Code Pattern Technically, a 1-1-1-1 beep code pattern doesn't exist but I've seen it and many readers have too. Most often, it's a problem with the system memory. This Phoenix BIOS issue is usually corrected by replacing the RAM. 1-2-2-3 Beep Code Pattern A 1-2-2-3 beep code pattern means that there has been a BIOS ROM checksum error. Literally, this would indicate an issue with the BIOS chip on the motherboard. Since replacing a BIOS chip is often not possible, this Phoenix BIOS issue is usually corrected by replacing the entire motherboard. 1-3-1-1 Beep Code Pattern A 1-3-1-1 beep code pattern on a PhoenixBIOS system means that there has b
to the PC expansion bus and have a dual LED display which decodes and displays the value at port http://www.vtel.com/support/catchall/phoenix1.htm 80h. With a POST board installed, you can monitor the progress http://www.comptechdoc.org/hardware/beepcodes/3.htm of the self-test as it progresses. Not all tests listed in the table below will be executed on all systems, nor will they always be executed in order. If a fatal error occurs, the PhoenixBIOS 4.0 will attempt to issue a beep code representing the error, and beep codes it will also attempt to display the error code on a monochrome or CGA display. In the event of a fatal system error during initialization, the code representing the portion of the POST causing the failure will be the last value sent to port 80h. As any experienced technician knows, a failure at any given location does not bios beep codes necessarily mean that the particular part or section under test has actually failed. Beep Code POST Code Failed Test Point / Description 1-1-1-3 02 Verify Real Mode 1-1-2-1 04 Get CPU type 1-1-2-3 06 Initialize system hardware 1-1-3-1 08 Initialize chipset registers with initial POST values 1-1-3-2 09 Set in POST flag 1-1-3-3 0A Initialize CPU registers 1-1-4-1 0C Initialize cache to initial POST values 1-1-4-3 0E Initialize I/O 1-2-1-1 10 Initialize Power Management 1-2-1-2 11 Load alternate registers with initial POST values 1-2-1-3 12 Jump to UserPatch0 1-2-2-1 14 Initialize keyboard controller 1-2-2-3 16 BIOS ROM checksum 1-2-3-1 18 8254 timer initialization 1-2-3-3 1A 8237 DMA controller initialization 1-2-4-1 1C Reset Programmable Interrupt Controller 1-3-1-1 20 Test DRAM refresh 1-3-1-3 22 Test 8742 Keyboard Controller 1-3-2-1 24 Set ES segment to register to 4 GB 1-3-3-1 28 Autosize DRAM 1-3-3-3 2A Clear 512K base RAM 1-3-4-1 2C Test 512 base address lines 1-3-4-3 2E Test 512K base memory 1-4-1-3 32 Test CPU bus-clock frequency 1-4-2-1 34 CMOS RAM read/write failure (thi
Home Page Beep Codes, Phoenix BIOS beep codes Phoenix BIOS beep codesPhoenix beep codes are the most detailed about. They use a system of 4 beeps each separated by a small pause i.e. 1 pause 2 pause 1 pause 1 pause (1-2-1-1), you may need to reboot the pc a few times in order to count all the beeps. To find out more information on Phoenix beep codes you can go here. Beep Code Description / What to Check 1-1-1-3 Verify Real Mode. 1-1-2-1 Get CPU type. 1-1-2-3 Initialize system hardware. 1-1-3-1 Initialize chipset registers with initial POST values. 1-1-3-2 Set in POST flag. 1-1-3-3 Initialize CPU registers. 1-1-4-1 Initialize cache to initial POST values. 1-1-4-3 Initialize I/O. 1-2-1-1 Initialize Power Management. 1-2-1-2 Load alternate registers with initial POST values. 1-2-1-3 Jump to UserPatch0. 1-2-2-1 Initialize keyboard controller. 1-2-2-3 BIOS ROM checksum. 1-2-3-1 8254 timer initialization. 1-2-3-3 8237 DMA controller initialization. 1-2-4-1 Reset Programmable Interrupt Controller. 1-3-1-1 Test DRAM refresh. 1-3-1-3 Test 8742 Keyboard Controller. 1-3-2-1 Set ES segment to register to 4 GB. 1-3-3-1 28 Autosize DRAM. 1-3-3-3 Clear 512K base RAM. 1-3-4-1 Test 512 base address lines. 1-3-4-3 Test 512K base memory. 1-4-1-3 Test CPU bus-clock frequency. 1-4-2-4 Reinitialize the chipset. 1-4-3-1 Shadow system BIOS ROM. 1-4-3-2 Reinitialize the cache. 1-4-3-3 Autosize cache. 1-4-4-1 Configure advanced chipset registers. 1-4-4-2 Load alternate registers with CMOS values. 2-1-1-1 Set Initial CPU speed. 2-1-1-3 Initialize interrupt vectors. 2-1-2-1 Initialize BIOS interrupts. 2-1-2-3 Check ROM copyright notice. 2-1-2-4 Initialize manager for PCI Options ROMs. 2-1-3-1 Check video configuration against CMOS. 2-1-3-2 Initialize PCI bus and devices. 2-1-3-3 Initialize all video adapters in system. 2-1-4-1 Shadow video BIOS ROM. 2-1-4-3 Display copyright notice. 2-2-1-1 Display CPU type and speed. 2-2-1-3 Test keyboard. 2-2-2-1 Set key click if enabled. 2-2-2-3 56 Enable keyboard. 2-2-3-1 Test for unexpected interrupts. 2-2-3-3 Display prompt "Press F2 to enter SETUP". 2-2-4-1 Test RAM between 512 and 640k. 2-3-1-1 Test expanded memory. 2-3-1-3 Test extended memory address lines. 2-3-2-1 Jump to UserPatch1. 2-3-2-3 Configure advanced cache registers. 2-3-3-1 Enable external and CPU caches. 2-3-3-3 Display external cache size. 2-3-4-1 Display shadow