Phoenix Bios Error Codes
Contents |
Eurosoft/Mylex Faraday A-Tease HP IBM Landmark Microid Research/Mr NCR Olivetti Phillips Phoenix Quadtel Supersoft Tandon Zenith Intel Motherboards: CA810E CC820 SE440BX-2 D810E2CB D810EMO D815BN D815EEA D815EPEA D820LP SE440BX SR440BX JN440BX LB440GX/L440GX N440BX/NA440BX OR840 T440BX phoenix bios continuous beep RC440BX VC820 Phoenix BIOS Text Error Messages Phoenix BIOS Post Procedures Phoenix XT phoenix award bios beep codes 2.52 PnP BIOS Post Codes Phoenix BIOS Plus or v1.0 BIOS Post Codes Phoenix UMC chipset PCI BIOS Post Codes Phoenix phoenix bios beep codes 1-3-4-3 PCI BIOS Post Codes Phoenix ISA/EISA/MCA v3.07 BIOS Post Codes Phoenix 4.0 BIOS Post Codes Phoenix 4.0 Release 6.0 BIOS Post Codes Phoenix BIOS Text Error Messages: Diskette drive A error Drive test 51k base memory error A: is present but fails the POST diskette tests. Check that the drive is defined with the proper diskette type in Setup and that the disk is installed correctly Extended RAM failed at offset: nnn Extended memory not working or not configured properly at offset: nnn Failing Bits: nnnn The hexadecimal number nnnn is a map of the bits at the RAM address that failed the memory
Phoenix Bios Beep Codes 1 Long Beep
test. Each 1 in the map indicates a failed bit Fixed Disk 0 Failure Fixed disk is not working or not configured properly. Check to see if fixed disk is installed properly. Run Setup to be sure the fixed disk type is correctly identified Fixed Disk 1 Failure Fixed disk is not working or not configured properly. Check to see if fixed disk is installed properly. Run Setup to be sure the fixed disk type is correctly identified Fixed Disk Controller Failure Fixed disk is not working or not configured properly. Check to see if fixed disk is installed properly. Run Setup to be sure the fixed disk type is correctly identified Incorrect Drive A: type - run Setup Type of diskette for drive A: not correctly identified in Setup Invalid NVRAM media type Problem with NVRAM (CMOS) access Keyboard controller error The keyboard controller failed test. Try replacing the keyboard Keyboard error Keyboard not working Keyboard error nn BIOS discovered a stuck key and displays the scan code nn for the stuck key Keyboard locked - Unlock key switch Unlock the system to proceed Monitor type does not match CMOS - Run Setup Monitor type not correctly identifie
starting the remainder of the boot process. If the computer passes the POST, the computer may give a single beep
Asus Beep Codes
(some computers may beep twice) as it starts and continue to boot. gigabyte beep codes However, if the computer fails the POST, the computer will either not beep or generate a beep hp beep codes code that tells the user the source of the problem. If your computer has an irregular POST or a beep code not mentioned below, follow the POST troubleshooting http://www.bioscentral.com/postcodes/phoenixbios.htm steps to determine the failing hardware component. AMI BIOS beep codes Award BIOS beep codes Dell beep codes IBM BIOS beep codes Macintosh startup tones Phoenix BIOS beep codes Motherboard help AMI BIOS beep codes Below are the AMI BIOS Beep codes that can occur. However, because of the wide variety of different computer manufacturers with http://www.computerhope.com/beep.htm this BIOS, the beep codes may vary. Beep Code Descriptions 1 short DRAM refresh failure 2 short Parity circuit failure 3 short Base 64K RAM failure 4 short System timer failure 5 short Process failure 6 short Keyboard controller Gate A20 error 7 short Virtual mode exception error 8 short Display memory Read/Write test failure 9 short ROM BIOS checksum failure 10 short CMOS shutdown Read/Write error 11 short Cache Memory error 1 long, 3 short Conventional/Extended memory failure 1 long, 8 short Display/Retrace test failed two-tone siren Low CPU Fan speed, Voltage Level issue AWARD BIOS beep codes Below are Award BIOS Beep codes that can occur. However, because of the wide variety of different computer manufacturers with this BIOS, the beep codes may vary. Beep Code Description 1 long, 2 short Indicates a video error has occurred and the BIOS cannot initialize the video screen to display any additional information 1 long, 3 short Video card not detected (reseat video card) or bad video card Beeps
Home Page Beep Codes, Phoenix BIOS beep codes Phoenix BIOS beep codesPhoenix beep codes are the most detailed about. They use a system of 4 beeps http://www.comptechdoc.org/hardware/beepcodes/3.htm each separated by a small pause i.e. 1 pause 2 pause 1 pause 1 pause (1-2-1-1), you may need to reboot the pc a few times in order to count all the beeps. To find out more information on Phoenix beep codes you can go here. Beep Code Description / What to Check 1-1-1-3 Verify Real Mode. 1-1-2-1 Get CPU type. 1-1-2-3 beep codes Initialize system hardware. 1-1-3-1 Initialize chipset registers with initial POST values. 1-1-3-2 Set in POST flag. 1-1-3-3 Initialize CPU registers. 1-1-4-1 Initialize cache to initial POST values. 1-1-4-3 Initialize I/O. 1-2-1-1 Initialize Power Management. 1-2-1-2 Load alternate registers with initial POST values. 1-2-1-3 Jump to UserPatch0. 1-2-2-1 Initialize keyboard controller. 1-2-2-3 BIOS ROM checksum. 1-2-3-1 8254 timer initialization. 1-2-3-3 8237 DMA controller bios beep codes initialization. 1-2-4-1 Reset Programmable Interrupt Controller. 1-3-1-1 Test DRAM refresh. 1-3-1-3 Test 8742 Keyboard Controller. 1-3-2-1 Set ES segment to register to 4 GB. 1-3-3-1 28 Autosize DRAM. 1-3-3-3 Clear 512K base RAM. 1-3-4-1 Test 512 base address lines. 1-3-4-3 Test 512K base memory. 1-4-1-3 Test CPU bus-clock frequency. 1-4-2-4 Reinitialize the chipset. 1-4-3-1 Shadow system BIOS ROM. 1-4-3-2 Reinitialize the cache. 1-4-3-3 Autosize cache. 1-4-4-1 Configure advanced chipset registers. 1-4-4-2 Load alternate registers with CMOS values. 2-1-1-1 Set Initial CPU speed. 2-1-1-3 Initialize interrupt vectors. 2-1-2-1 Initialize BIOS interrupts. 2-1-2-3 Check ROM copyright notice. 2-1-2-4 Initialize manager for PCI Options ROMs. 2-1-3-1 Check video configuration against CMOS. 2-1-3-2 Initialize PCI bus and devices. 2-1-3-3 Initialize all video adapters in system. 2-1-4-1 Shadow video BIOS ROM. 2-1-4-3 Display copyright notice. 2-2-1-1 Display CPU type and speed. 2-2-1-3 Test keyboard. 2-2-2-1 Set key click if enabled. 2-2-2-3 56 Enable keyboard. 2-2-3-1 Test for unexpected interrupts. 2-2-3-3 Display prompt "Press F2 to enter SETUP". 2-2-4-1 Test RAM between 512 and 640k. 2-3-1-1 Test expanded memory. 2-3-1-3 Test extended memory address lines. 2-3-2-1 Jump to UserPatch1. 2-3-2-3 Configur