Brother Hl-2035 Laser Printer Drum Error
Contents |
not reset properly after putting in a new cartridge. You may still have a ‘toner low' or ‘toner empty' message. It is possible to manually reset the printer to remove this message: Ensure the printer is brother hl 2035 drum unit reset instructions turned off. Open the printer front cover. Hold the Go button while turning the
Brother Hl 2035 Red Error Light
printer on. When the Toner, Drum, and Error LEDs are on and the Ready LED is off, release the GO button. All
Brother Hl 2035 Toner
of the LEDs will turn off. Press the Go button two (2) times. The Toner, Drum, and Error LEDs will turn on. TN2005 cartridge - Press the Go button six (6) times. The Error LED
Brother Hl 2035 Toner Reset
should now be flashing, close the front cover. Brother HL-2035 - Reset Drum After changing a DR2005 drum unit in a Brother HL-2035, the printer’s page count needs to be reset. This will turn off the drum warning light on the printer. Simply open the front cover, and hold the “GO” button until all four LED’s are lit. Release the “GO” button and close the front cover. Youtube Video: Drum Reset Brother HL-2035 - Change Toner Cartridge Youtube Video: Change Toner Cartridge Tags: BrotherChange Toner CartridgeDR2000DR2005Reset DrumReset Toner CartridgeTN2005 Next story Brother HL-2037 Previous story Brother HL-2070 You may also like... Brother MFCJ4610DW - Changing the Cartridges 23 Sep, 2013 Brother DCP-130C 30 Jan, 2015 Brother DCP-165C 30 Jan, 2015 2 Responses Comments2 Pingbacks0 Colin Mealor says: June 17, 2013 at 6:32 pm Hmm that didn't work for me - the Toner light is still on Neil says: June 16, 2015 at 12:35 pm It worked once but the **** keeps on lighting up again. Printer now binned. 3D Showcase 3D Showcase / Flashforge Creator Pro / Tinkercad Tinkercad Drinks Coaster - Square Voroni 19 Sep, 2015 3D Showcase / Flashforge Creator Pro / Tinkercad Tinkercad Drinks Coaster 14 Sep, 2015 3D Showcase / Tinkercad 3D design with Tinkercad 13 Sep, 2015 3D Showcase / Flashforge Creator Pro 3D Print - Twisted Vase 30 May, 2015 Recent PostsPopular PostsRecent CommentsTags 3D Showcase / Flashforge Creator Pro / Tinkercad Tinkercad Drinks Coaster - Square Voroni 19 Sep, 2015 3D Showcase / Flashforge Creator Pro / Tinkercad Tinkercad Drinks Coaster 14 Sep, 2015 3D Showcase / Tinkercad 3D design with Tinkercad 13 Sep, 2015 3D Showcase / Flashforge Creator Pro 3D Print - Twisted Vase
Standard Operating Procedure for Changing the Toner Cartridge in a Printer How to Clean a Canon Copier Drum How to Replace a Toner Chip for a Lexmark Share on Facebook Some laser printers, including many business-oriented black and white and color units, use http://yourbusiness.azcentral.com/stop-drum-light-blinking-printer-13258.html an imaging drum that is separate from the toner cartridge. The drum is coated with a chemical that develops a charge when light strikes it, making toner stick to it. Over time, imaging drums break down and lose their effectiveness and require replacement. http://www.refreshcartridges.co.uk/igloo/drum-led-flashes-after-changing-brother-dr2005/ To signal you that your drum is nearing the end of its life, your printer's drum light will flash. Once it starts doing this, you should obtain a new drum so that you can replace the old one before the printer stops working or brother hl its print quality declines. HP Color LaserJet 2550, 2500 and 1500 Series Drum Replacement Procedure Step 1 Flip the "Power" switch to turn the printer on. Wait for it to warm up. Step 2 Open the printer's top cover by lifting its front edge up and rotating it vertically. Step 3 Push the old imaging drum slightly away from you and lift it upward to remove it from the printer. Step 4 Wipe any dust or debris off of the clear plastic strip that sits inside the brother hl 2035 printer under where the drum was. Use a dry microfiber cloth to avoid leaving deposits or scratches on the plastic. Step 5 Remove the new drum from its plastic bag, set it down and pull the orange rings and orange shipping spacers away from the drum. Rotate and then pull the orange locks on the two ends of the drum assembly to remove them from the cartridge. Step 6 Lift the orange protective cover away from the imaging drum surface. Step 7 Lower the new drum into the printer by lining up its white rollers with the arrow markings inside the printer. You might need to use a little bit of force to properly seat it. Step 8 Close the printer's top cover. Step 9 Press the "Go" button on the printer's main control panel and wait for its "Ready" light to turn on. Brother HL-2035 Series Drum Replacement Procedure Step 1 Open the printer's front cover by placing your hands on either side of the printer and rotating it down. The printer should be turned on for this process. Step 2 Reset the blinking drum light by holding down the printer's "Go" button for approximately four seconds. Do not release it until the four light-emitting diode indicator lights on the printer's control panel light up. Step 3 Pull the combined drum and toner assembly out of the printer. It should come straight out. Step 4 Remove the toner cartridge from the drum assembly. Press down on the blue lever to release the cartridge. Set it down carefully
Ink CartridgesBrother CartridgesCanon CartridgesDell CartridgesEpson CartridgesHP CartridgesKodak CartridgesAdvent CartridgesApple CartridgesBT CartridgesCompaq CartridgesIBM CartridgesDymo CartridgesLexmark CartridgesOlivetti CartridgesSamsung CartridgesSharp CartridgesXerox CartridgesToner CartridgesBrother TonerDell TonerEpson TonerHP TonerLexmark TonerOKI TonerCanon TonerKyocera TonerMinolta TonerPanasonic TonerRicoh TonerTally TonerSamsung TonerXerox TonerFax RollsBrother Fax RollsCanon Fax RollsDaewoo Fax RollsPanasonic Fax RollsPhilips Fax RollsSagem Fax RollsSharp Fax RollsXerox Fax RollsFrankingFramaFrancotyp PostaliaPitney BowesNeopostFranking LabelsPaperA4 Gloss Inkjet Paper6" x 4" Photo CardLaminating PouchesA4 Adhesive LabelsA4 Copier PaperFranking Labels7" x 5" Photo Card8" x 6" Photo CardA1 Gloss Inkjet PaperA3 Copier PaperA3 Gloss Inkjet PaperA4 Matt Inkjet PaperA6 Gloss Inkjet PaperCD & DVD LabelingDouble Sided PaperSatin Inkjet PaperT-Shirt Transfer PaperAccessoriesBatteriesCablesHardwareMediaInkjet RefillingStationery « Canon MPC190 Waste Ink Tank Counter Reset Fixing Faded Prints with HP Colour LaserJet » Drum LED flashes after changing Brother DR2005/DR2000 Drum Unit Drum LED flashes after changing Brother DR2005/DR2000 Drum Unit 2011-10-06T13:01 October 6, 2011 Printers manufactured by Brother that take the DR2005 & DR2000 drum units need to be told by a simple prompt when the drum has been changed. If you have recently changed your drum but still have a blinking LED on the front of the printer the drum counter was either not reset or not reset correctly. To reset the drum counter follow the simple instructions below: Open the front door of the printer. Press and hold the GO button for approximately four seconds until all the LEDs light up. Once all four LEDs are lit, release the button. Close the front door of the printer. The counter should now be reset leaving you to continue printing. If however the LED is still flashing please contact whoever the drum was purchased from for further support. This advice applies to a variety of Brother printers and fax machines including the HL-2030, HL-2030R, HL-2035, HL-2035R, HL-2040, HL-2040R, HL-2070N & HL-2070NR. About the author Matthew Stevenson I have been involved in the printer industry since I was 18 and have been an employee of Refresh Cartridges since early 2009. I am a dedicated family man, gamer, music fan and friend to all. I write the majority of the content here on Igloo and am responsible for its upkeep. 3 comments bongo January 23, 2014 at 10:10 am (UTC 0) Reply worked a trea