Brother Hl-5370dw Toner Error
Contents |
solid red).I have tried replacing the toner with brand new 3rd party and OEM toners. It still tells me to replace the
Brother Hl 5370dw Toner Light Reset
toner.I have reset all factory settings.I have tried taping over (what I brother hl 5370dw manual think is) the toner sensor.It still tells me to replace the toner and will not print.Any thoughts? Respond to brother hl 5370dw drum this 0 I can confirm the prior comments. I have an HL-5370DW, and my toner light had been coming on for 4-5 days when printing before it finally refused to print.
Brother Hl 5370dw Driver
I looked around and discovered that Brother has built in various you-must-buy-new-toner mechanisms into its printers. To defeat them:1. Open the door, and remove the toner from its carriage. Apply electrical tape/a sticker/something dark and sticky to the clear plastic windows on BOTH sides of the toner cartridge. Replace toner in carriage. (marking with permanent marker is no longer enough, brother has
Brother Hl 5370dw All Lights Flashing
upgraded their lasers)2. Run the toner reset sequence (taken from Ananda Q)2.1. With Printer off open the toner door2.2. Hold the Go button as you turn the printer on.2.3. All lights will turn on. Keep holding Go until status light goes off.2.4. Press the Go button 2x.2.5. The Paper, Drum & Toner light will come on2.6. Press Go 6x2.7. Status light will turn red2.8. Close the front.Worked like a charm. by unknown on Sep 26, 2011 at 11:32am Add comment Please sign in to comment 0 Yup, like a charm, THX! by sonny3010 on Mar 7, 2012 at 6:00pm Add comment Please sign in to comment 0 I use whiteout to cover the holes, that seems to do the trick. by unknown on Aug 7, 2012 at 6:49am Add comment Please sign in to comment 0 Well I tried everything and THIS WORKED!! by unknown on Dec 20, 2013 at 5:06pm Add comment Please sign in to comment Please sign in to comment Brother HL 5370DW Buy discount ink Buy this printer More Brother questions © Copyright 2011-2016, FixYourOwnPrinter.com, Inc. Privacy Policy Terms of Use
only takes a few minutes. Join Now We have a small Brother mono laser printer on our network. After it ran out of toner the first time, it was left to sit empty brother hl 5370dw factory reset for awhile, as it wasn't critical and our office equipment solutions provider took some
Brother Hl 5370dw Print Configuration Page
time getting us a new toner pack. Having replaced the cartridge, the printer works, but Spiceworks still detects it as 'less brother hl 5370dw wireless setup than 2%.' It's not critical to the functions of the office, but it sends me half a dozen emails a day. How do I force detection of proper toner levels? Where do I go to http://fixyourownprinter.com/posts/68528 stop messages from that printer? (The world won't end if I don't know it's out of toner, so updates from it aren't really necessary.) Reply Subscribe View Best Answer RELATED TOPICS: Brother HL-4040CN Printer not showing corrent toner levels Problem with Brother HL-5380DN printer Toner levels. toner level Brother 5250DN   This topic was created during version 6.0. The latest version is 7.5.00093. 12 Replies Thai Pepper OP https://community.spiceworks.com/topic/256272-brother-hl-5370dw-insists-that-it-s-always-out-of-toner Best Answer Mike Davis Sep 6, 2012 at 3:37 UTC Extra Mile Technology Services is an IT service provider. Someone just did a write up on this and found that using non-genuine Brother cartridges causes this. 0 Thai Pepper OP JRC Sep 6, 2012 at 3:37 UTC Try having spice works do a network scan. Perhaps it just needs to update it's internal DB. Does the printer itself think it is that low on toner? 1 OP Aaron M (Spiceworks) Sep 6, 2012 at 3:55 UTC If the printer's admin inteface reports the correct amount, but Spiceworks doesn't, it may boil down to an issue with SNMP. SNMP is how Spiceworks collects toner information from printers. My experience with Brother printers is that some don't actually report a value, but rather something along the lines of "yes there's some toner" or "i'm out of toner." If you run an snmpwalk against the printer and send the resulting log file to support@spiceworks.com, I can take a look at it and confirm that for you. 0 Datil OP Brian Steingraber Sep 6, 2012 at 4:04 UTC What toner status does the device show? For our Brother MFC-9010, per the instructions, you have to
by a Fortune 500 verification firm. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Ask Russell H. Your Own Question Russell H., Printer and Office Tech Category: Printers Satisfied Customers: 9191 Experience: 11+ yrs experience, inkjets & lasers, from huge to portable 13568747 Type Your Printers Question Here... Russell H. is online now Brother HL 5370DW toner light wont go off. Customer Question Brother HL 5370DW toner light won't go off despite new cartridge.Will not print.I installed a new cartigde which is properly in place Submitted: 4 years ago. Category:Printers Share this conversation Expert: Russell H. replied4 years ago. Try a hard reset of the printer:Turn the printer OFF, when it is on, by suddenly and sharply unplugging it from the power source.Also unplug it from the computer!Leave it that way for 10 minutes.Plug it back in.Turn it on if it didn't turn itself on. Wait for it to initialize.Try printing again. Ask Your Own Printers Question Customer: replied4 years ago. I tried as you advised but printer still does not print and yellow light stays on. I took our cartridige and and reinserted. Still not printing, Customer: replied4 years ago. Problem in not fixed.Any other ideas befroe i go out an buy another $100 cartidige. Customer: replied4 years ago. Not fixed yet Expert: Russell H. replied4 years ago. What does the printer's Status Monitor state about the printer's status? Does it still say, "Replace toner" or "No Toner" or "Cartridge position error" or "Low Toner" ?Are any other lights than the Toner light, flashing or On?Is the Toner light itself flashing, or is it steadily On?In any case, to get the printer back into a normal-ish (operational) status, you need to try the following:Turn Off the Brother machine. Leave it that way for a half minute or longer.Then, hold down the GO button on the Brother machine, and