Error Light On Brother Hl-2140
Contents |
CopiersBrotherHLHL-2040 Laser PrinterHl 2140 error light... Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Question about Brother HL-2040 Laser Printer brother printers 9 Answers Hl 2140 error light is flashing Error light is flashing Posted error light on brother hl 2170w by wa47ma on Sep 14, 2008 Want Answer 0 Clicking this will make more experts see the question and brother hl 2140 error printing we will remind you when it gets answered. 5 Comments Flag More Print this page Share this page × Moderate Help this question get an answer Is this question mis-categorized or about http://support.brother.com/g/b/producttop.aspx?c=us&lang=en&prod=hl2140_all a different product? Help this question get an answer by entering the correct category or product below. Did you mean? Yes No Cancel Update (+2 points) 3 more comments emilyelle Oct 29, 2008 I have the same problem, and nothing will make the light go off. There is no paper jam. Both covers are closed. I have held the Go button down and that doesn't http://www.fixya.com/support/t1040446-hl_2140_error_light_flashing help. The printer will not print anything. I have the same problem, and nothing will make the light go off. There is no paper jam. Both covers are closed. I have held the Go button down and that doesn't help. The printer will not print anything. postal dude Dec 22, 2008 Same exact thing here. Flashing red "error" light, nothing in memory, doors all closed, even uninstalled and reinstalled Same exact thing here. Flashing red "error" light, nothing in memory, doors all closed, even uninstalled and reinstalled jimbomojo Apr 02, 2009 same exact problem. no paper jam. memory is not full. cover is closed, etc. I have checked everything but can't get the error light to stop flashing. very frustrating. same exact problem. no paper jam. memory is not full. cover is closed, etc. I have checked everything but can't get the error light to stop flashing. very frustrating. LaDancerly Jul 05, 2014 Exact problem. And I thought I had checked everything, but it was indeed a paper jam caused by a tiny rip of paper 1cm x 50mm must have torn of a sheet at some stage. I finally
toner , i still get the drum / error message still ???2. i also clean the cornora wire , using the green tab 3. someone mention the toner level senor port , where is this located ??4. every other page is http://www.fixyourownprinter.com/posts/63546 a paper jammedplease leave message at either place: [emailprotected] -- or [emailprotected]THANKS AGAIN FOR YOUR TIME / HELP Respond to this 0 The drum/error is a drum error not sure why you would think the toner cartridge would fix the issue. https://printerthinker.com/brother-hl-2140/ I dont have one of those around but usually the corona wire cleaner is blue. I dont really like them becuase they dont do a good job. I usually use a damp Q-tip and alcohol. The toner level sensor port is brother hl on the right side of where the toner sits in the machine. For the error you described however you would need to check and clean the contacts for the drum on the left side of the inside of the machine. by nivek on Aug 24, 2009 at 7:09pm Add comment Please sign in to comment 0 but if it's a drum life error then you either need to replace it and/or reset the counter.to reset the drum counter, open the fron cover, brother hl 2140 hold down the start button until all lights lit up. then release the button and shut the front cover. by tk55 on Aug 24, 2009 at 9:17pm Add comment Please sign in to comment I tried TK55's steps and it didn't work for me. Then I tried a variation and it did work. Here's what I did:(Essentially the cartridge/drum unit should not be in the printer when you reset it)1) Open front door2) Remove the cartridge/drum unit3) Hold down front button until all lights come on4) Put cartridge/drum unit back in5) Close the front doorThe Drum life should be reset.Hope this helps - unknown hello i just had this printer for 2 months , it first came with an factory toner which yield an 1,000 copies. I just bought a new generic toner, but still the same problemas for resetting the drum counter , i try that , it's doesn't work. PSS - I FORGOT TO MENTION THAT EVERY OTHER PAGE , THERE AN PAPER JAMMED TOO .THANKS AGAIN FOR YOUR TIME /HELP - jbj168 0 if the printer has only done just over a 1000 pages, then it won't be a drum life error.when there's a paper jammed error, did you actually have a paper jammed? if it's a false alarm, it would be caused by high voltage arcing in the corona wire assembly. a very common problem with brother printers.i normally pull the drum cartridge apart to clean the charge assembly properly. i
not reset properly after putting in a new cartridge. You may still have a ‘toner low' or ‘toner empty' message. It is possible to manually reset the printer to remove this message: Ensure the printer is turned off. Open the printer front cover. Hold the Go button while turning the printer on. When the Toner, Drum, and Error LEDs are on and the Ready LED is off, release the GO button. All of the LEDs will turn off. Press the Go button two (2) times. The Toner, Drum, and Error LEDs will turn on. Depending on your cartridge: TN2110 cartridge - Press the Go button five (5) times. TN2120 cartridge - Press the Go button six (6) times. The Error LED should now be flashing, close the front cover. Brother HL-2140 - Reset Drum After changing a DR2100 drum unit in a Brother HL-2140, the printer’s page count needs to be reset. This will turn off the drum warning light on the printer. Simply open the front cover, and hold the “GO” button until all four LED’s are lit. Release the “GO” button and close the front cover. Youtube Video: Drum Reset Brother HL-2140 - Change Toner Cartridge Youtube Video: Change Toner Cartridge Tags: BrotherChange Toner CartridgeDR2100HL-2140Reset DrumReset Toner CartridgeTN2110TN2120 Next story Brother HL-2150 Previous story Brother HL-2037 You may also like... Brother HL-5350 1 Dec, 2012 Brother MFC-9840CDW 18 Mar, 2014 Brother HL-2030 27 Nov, 2012 3 Responses Comments3 Pingbacks0 Paul says: May 15, 2014 at 4:04 pm After resetting the indicators, it won't print. Printer Thinker says: May 17, 2014 at 6:14 pm Does it try to print, in other words does the page come out blank? Or do you send a print job but nothing happens at all? Lauren says: February 12, 2015 at 6:57 pm Thank you for the help! It worked. 🙂 It seems that every time a toner needs to be replaced this needs to be done. 3D Showcase 3D Showcase / Flashforge Creator Pro / Tinkercad Tinkercad Drinks Coaster - Square Voroni 19 Sep, 2015 3D Showcase / Flashforge Creator Pro / Tinkercad Tinkercad Drinks Coaster 14 Sep, 2015 3D Showcase / Tinkercad 3D design with Tinkercad 13 Sep, 2015 3D Showcase / Flashforge Creator Pro 3D Print - Twisted Vase 30 May, 2015 Recent PostsPopular PostsRecent CommentsTags 3D Showcase / Flashforge Creator Pro / Tinkercad Tinkercad Drinks Coaster - Squar