Impresora Brother Hl-2140 Error Drum
Contents |
Instructable »Brother HL 2140 Toner Life End Error Hack by VentingIntrovert in computers Download 5 Steps Share Favorite I Made it! Collection Intro Intro: Brother HL 2140 Toner Life End Error HackOne of the most frustrating issues for a college brother hl-2170w drum replacement student is receiving a toner error after printing 18 of the 20 pages of
Brother Hl 2170w Drum Error Light Flashing
your final paper due the ... 1 Step 1: Remove Drum and Toner Assembly1. Remove the front access panel to access brother hl 2140 all lights flashing the drum and toner assembly. 2. Remove drum assembly by pulling on the drum handle. 3. Once the drum assembly ... 2 Step 2: Bypassing the Toner Sensors1. Now that the toner cartridge is http://support.brother.com/g/b/faqend.aspx?c=us&lang=en&prod=hl2140_all&faqid=faq00000170_017 removed, pick it up and look for the glass window on the sides. 2. Find thewindow that is most accessible and ... 3 Step 3: Test Run1. According to my research, at this point some models of Brother printers (including the HL 2140) should work and be ready to print. 2. To test this, ... 4 Step 4: Resetting the PrinterFor some reason my printer still did not work following http://www.instructables.com/id/Brother-HL-2140-Toner-Life-End-Error-Hack/step4/Resetting-the-Printer/ the previous step and my toner light was steadily lit. Due to the fact that my cartridge was ... 5 Step 5: Status PageIt's good idea to print a status page to see all the statistics regarding your printer. It will list number of pages printed, toner capacity, drum capacity, paper ...Step 4: Resetting the PrinterShow All ItemsFor some reason my printer still did not work following the previous step and my toner light was steadily lit. Due to the fact that my cartridge was a starter cartridge, and there weren’t any gears that I needed adjust, I needed to reset the page counter in my printer.1. To do that, turn off your printer and open the front access panel.2. Press and hold the white button, while turning on the printer. The toner, drum and error lights should remain lit.3. Release the white button and press it again twice.4. Release, pause and press again five times.5. If done correctly, when you plug your printer to your computer it should try to reinstall the drivers under Brother Maintenance Mode. Your computer will fail and will not find the appropriate drivers.6. Unplug your printer, turn it off, turn on and connect to the computer.7. Your computer should
toner , i still get the drum / error message still ???2. i also clean the cornora wire , using the green tab 3. someone mention the toner level senor port , http://www.fixyourownprinter.com/posts/63546 where is this located ??4. every other page is a paper jammedplease leave message at either place: [emailprotected] -- or [emailprotected]THANKS AGAIN FOR YOUR TIME / HELP Respond to this 0 The drum/error is a drum error not sure why you would think the toner cartridge would fix the issue. I dont have one of those around but usually the corona wire cleaner is blue. I dont really like them becuase they dont brother hl do a good job. I usually use a damp Q-tip and alcohol. The toner level sensor port is on the right side of where the toner sits in the machine. For the error you described however you would need to check and clean the contacts for the drum on the left side of the inside of the machine. by nivek on Aug 24, 2009 at 7:09pm Add comment Please sign in to comment brother hl 2140 0 but if it's a drum life error then you either need to replace it and/or reset the counter.to reset the drum counter, open the fron cover, hold down the start button until all lights lit up. then release the button and shut the front cover. by tk55 on Aug 24, 2009 at 9:17pm Add comment Please sign in to comment I tried TK55's steps and it didn't work for me. Then I tried a variation and it did work. Here's what I did:(Essentially the cartridge/drum unit should not be in the printer when you reset it)1) Open front door2) Remove the cartridge/drum unit3) Hold down front button until all lights come on4) Put cartridge/drum unit back in5) Close the front doorThe Drum life should be reset.Hope this helps - unknown hello i just had this printer for 2 months , it first came with an factory toner which yield an 1,000 copies. I just bought a new generic toner, but still the same problemas for resetting the drum counter , i try that , it's doesn't work. PSS - I FORGOT TO MENTION THAT EVERY OTHER PAGE , THERE AN PAPER JAMMED TOO .THANKS AGAIN FOR YOUR TIME /HELP - jbj168 0 if the printer has only done just over a 1000 pages, then it won't