Cause No. 111 - Protocol Error Unspecified
Contents |
CLASS Cause 1 Unallocated (unassigned) number - This cause indicates that the called party cannot be reached because, although the called party number is in a valid isdn disconnect cause codes format, it is not currently allocated (assigned). Cause 2 No route to ss7 release cause codes specified transit network - This cause indicates that the equipment sending this cause has received a request to route sip cause codes the call through a particular transit network which it does not recognize. The equipment sending this cause does not recognize the transit network either because the transit network does not exist or
Q.850 Cause Codes
because that particular transit network, while it does exist, does not serve the equipment that is sending this cause. This cause is supported on a network dependent basis. Cause 3 No route to destination - This cause indicates that the called party cannot be reached because the network through which the call has been routed does not serve the destination desired. This cause normal unspecified is supported on a network-dependent basis. Cause 4 Send special information tone - This cause indicates that the called party cannot be reached for reasons that are of long term nature and that the special information tone should be returned to the calling party. Cause 5 Misdialed trunk prefix - No procedures specified for US networks. Cause 8 Preemption - This cause indicates that the call is being preempted. Cause 9 Preemption - Circuit reserved for reuse. This cause indicates that the call is being preempted and the circuit is reserved for reuse by the preempting exchange. Cause 16 Normal call clearing - This cause indicates that the call is being cleared because one of the users involved in the call has requested that the call be cleared. Under normal situations, the source of this cause is not the network. Cause 17 User busy - This cause is used to indicate that the called party is unable to accept another call because the user busy condition has been encountered. This cause value may be generated by the called user or by the network. In the case
rate. Web control panels; Least Cost Routing; Excel tariff uploads; SIP and H323 support. H323 SIP softswitch >> Site cause code 41 temporary failure highlights Home page Online Calculators Products Excel call center VoIP services Technical
Protocol Error Unspecified 111 Reason
papers What is an Erlang? Contact us VoIP calling Premium quality termination for wholesale carriers with their own
Cause Code Technologies
VoIP switch. 44Direct >> Our lowest rates for wholesale carriers with their own VoIP switch. 44Mobile >> Our unique online callshop billing system. Bill My Calls >> 111 protocol https://www.dialogic.com/webhelp/MSP1010/10.2.3/WebHelp/MSP_DG/ISUP/Cause_Codes.htm error, unspecified Erlang for Excel An Add-In for Microsoft Excel that lets you use Erlang B and C functions in your own Excel spreadsheets. The ultimate in Erlang traffic modelling flexibility and data sharing. Erlang Calculators An easy to use and fast Windows product offering Erlang B, Extended Erlang B, Erlang C and Call Minutes calculators. Four products in one, http://www.erlang.com/forum/erlang/thread.htx?thread=6278 plus Erlang for Excel free. VoIP Calculator Our entry level VoIP calculator allowing you to easily calculate your Voice over IP bandwidth requirements. Supports multiple codecs and packet intervals and RTP header compression. Wallis Dudhnath - 14th August 2015 (15:25 GMT)Related to the codes from ISDN. General purpose protocol code that captures errors that cannot be easily quantified. Indicates a protocol error not a violation. VBR/ Wallis Dudhnathkathir - 14th August 2015 (10:33 GMT)Skip indicator : 0 Protocol discriminator : (6) Radio resources management messages Message type : 40 Value : (111) Protocol error, unspecifiedKasem - 28th November 2013 (17:43 GMT)Hi, we had the same problem before with inter BSC Handover when the encryption different in two BSCs Thanksrashed - 27th November 2013 (08:03 GMT)Value : Tems message shows(111) Protocol error for HO failure,i want to known what is the reson for HO failure No ping pong Ho,RX LEV,RX QUAL is also good,no TRX problemUbaid - 7th July 2010 (09:23 GMT)In my experience normally these HO failures are due to the non sychronization of BTS. Ju
Cause No. 2 - No route to specified transit network (national use) [Q.850] This cause indicates that the equipment sending this cause has received http://www.cnes.com/causecodes.html a request to route the call through a particular transit network which it does not recognize. The equipment sending this cause does not recognize the transit network either because the transit network does not exist or because that particular transit network. While it does exist. does not serve the equipment which is sending this cause. Cause No. 3 - No route to destination cause code [Q.850] This cause indicates that the called party cannot be reached because the network through which the call has been routed does not serve the destination desired. This cause is supported on a network dependent basis. Cause No. 4 - send special information tone [Q.850] This cause indicates that the called party cannot be reached for reasons that are of a long term nature protocol error unspecified and that the special information tone should be returned to the calling party. Cause No. 5 - misdialed trunk prefix (national use) [Q.850] This cause indicates the erroneous inclusion of a trunk prefix in the called party number. This number is to sniped from the dialed number being sent to the network by the customer premises equipment. Cause No. 6 - channel unacceptable [Q.850] This cause indicates that the channel most recently identified is not acceptable to the sending entity for use in this call. Cause No. 7 - call awarded. being delivered in an established channel [Q.850] This cause indicates that the user has been awarded the incoming call and that the incoming call is being connected to a channel already established to that user for similar calls (e.g. packet-mode x.25 virtual calls). Cause No. 8 - preemption [Q.850] This cause indicates the call is being preempted. Cause No. 9 - preemption - circuit reserved for reuse [Q.850] This cause indicates that the call is being preempted and the circuit is reserved for reuse by the preempting exchange. Cause No. 10 - normal call clearing [Q.850] T