Calculate Packet Error Rate Bit Error Rate
Contents |
be challenged and removed. (March 2013) (Learn how and when to remove this template message) In digital transmission, the number of bit errors is the number of received bits how to calculate bit error rate in matlab of a data stream over a communication channel that have been altered
Packet Error Rate Bch
due to noise, interference, distortion or bit synchronization errors. The bit error rate (BER) is the number of bit
Packet Error Rate Wifi
errors per unit time. The bit error ratio (also BER) is the number of bit errors divided by the total number of transferred bits during a studied time interval. BER
Packet Error Rate Formula
is a unitless performance measure, often expressed as a percentage.[1] The bit error probability pe is the expectation value of the bit error ratio. The bit error ratio can be considered as an approximate estimate of the bit error probability. This estimate is accurate for a long time interval and a high number of bit errors. Contents 1 Example 2 Packet bit error rate calculation error ratio 3 Factors affecting the BER 4 Analysis of the BER 5 Mathematical draft 6 Bit error rate test 6.1 Common types of BERT stress patterns 7 Bit error rate tester 8 See also 9 References 10 External links Example[edit] As an example, assume this transmitted bit sequence: 0 1 1 0 0 0 1 0 1 1 and the following received bit sequence: 0 0 1 0 1 0 1 0 0 1, The number of bit errors (the underlined bits) is, in this case, 3. The BER is 3 incorrect bits divided by 10 transferred bits, resulting in a BER of 0.3 or 30%. Packet error ratio[edit] The packet error ratio (PER) is the number of incorrectly received data packets divided by the total number of received packets. A packet is declared incorrect if at least one bit is erroneous. The expectation value of the PER is denoted packet error probability pp, which for a data packet length of N bits can be expressed as p p = 1 − ( 1 − p e ) N {\displaystyle p_{p}=1-(1-p_{e})^{N}}
C.S0033 Tests Performed Using PER How is a PER Measurement Made? Packet Error Rate (PER) is used to test the performance of an access terminal's receiver. PER is the ratio, in percent, of the number of FTAP bit error rate test or FETAP Test Packets not successfully received by the access terminal (AT) to the bit error rate example number of FTAP or FETAP Test Packets sent to the AT by the test set. See Forward Test Application Protocol (FTAP) bit error rate vs snr , Multi-carrier Test Application Protocol and Forward Enhanced Test Application Protocol (FETAP) . To perform a packet error rate measurement, the test set sends an FTAP (when current physical layer subtype is subtype 0) or https://en.wikipedia.org/wiki/Bit_error_rate FETAP Test Packet (when current physical layer subtype is subtype 2) or FMCTAP Test Packet (when current physical layer subtype is subtype 3) to the access terminal. See Release A Physical Layer Subtype or Release B Physical Layer Subtype to configure the physical layer subtype. Each packet contains 16 FCS (Frame Check Sequence) bit, which provide information about the packet. If the AT is able to decode the packet and http://rfmw.em.keysight.com/rfcomms/refdocs/1xevdo/1xevdo_meas_cperror_desc.html the FCS checks (the information relayed by the FCS matches the packet characteristics), then the packet is successfully received. The AT sends one or more FTAP/FETAP/FMCTAP Loop Back Packets to the test set to indicate how many FTAP/FETAP/FMCTAP Test Packets were successfully received for each 16-slot "observation interval" (frame). The AT sends one Loop Back Packet (or more, if needed to convey all of the records) containing a record for each FTAP/FETAP/FMCTAP Test Packet in the observation interval. The Loop Back Packets are queued for transmission on the Reverse Traffic Channel, and the AT must provide buffering for at least 8 FTAP/FETAP/FMCTAP Loop Back Packets. An FTAP/FETAP/FMCTAP Loop Back Packet is generated even if no FTAP/FETAP/FMCTAP Test Packets were received during the 16-slot observation interval. In performing the PER measurement, the test set: always operates with 100% packet activity (see Fixed Settings ). 100% packet activity means that all slots contain Forward Traffic Channel or Control Channel packets (data). The test set fills any empty slots with filler data directed to a random AT other than the AT under test. (0% packet activity means that the source is pulsed off when there is no data to transmit in the slot, and then pulsed on to transmit the MAC a
how do i transfrom "Bit Error Rate" to "frame Error Rate"? Messages sorted by: [ date ] [ thread ] [ subject ] http://mailman.isi.edu/pipermail/ns-users/2006-October/057413.html [ author ] If you plug the values in the formula PER=1-(1-0.001)^8000 = 0.9996658 The above result implies that 99.96% of you packets will have errors and if there are no additional error correction mechanisms, they will be dropped/lost. A BER of 10^-3 is too high and is not practical. For example, in most wireless scenarios, the BER is assumed to be 10^-6. By error rate the way, why are you posting this in ns-users list? Abdul. ªL®õ¨¶ wrote: > for example : > when I give ber=10^-3, packet size=1000bytes, what is PER? > > -----Original Message----- > From: Abdul Jabbar [mailto:jabbar at gmail.com] > Sent: Monday, October 02, 2006 6:24 PM > To: ªL®õ¨¶ > Cc: ns-users at isi.edu > Subject: Re: [ns] how do i transfrom "Bit Error Rate" bit error rate to "Packet Error > Rate"? > > As far as I know, the relationship between BER and PER , assuming that > bit errors are independent and uniformly distributed is, > > PER=1-(1-BER)^N where N is the number of bits. > > However, the above formula is only approximate because in real life > scenarios, the bit errors are not completely independent but may occur > in bursts. Further, the error distribution is also not exactly uniform. > > Hope it helps.... > > Cheers, > Abdul. > > ªL®õ¨¶ wrote: > >> ------------------------------------------------------------------------ >> >> Hi all, how can I transform ¡§Bit error Rate¡¨ to ¡§packet error rate¡¨? >> >> >> >> Is there any formulas for this ? >> >> >> >> Can any body help me? >> >> >> >> >> > > > > > Previous message: [ns] FW: how do i transfrom "Bit Error Rate" to "Packet Error Rate"? Next message: [ns] FW: how do i transfrom "Bit Error Rate" to "frame Error Rate"? Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] More information about the Ns-users mailing list