Dial Up Modem Error 678
Contents |
differentOperating SystemWindows98Windows95WindowsMEWindowsNTWindows2000WindowsXPWindowsVistaWindows7Windows8Mac OS-9 Mac OS-X Linspire Common Connection Errors / SolutionsError 678: Remote modem not respondingSeveral factors can cause the 'Remote modem not responding' error. The following information should help you to identify error 678 modem movistar the cause of the error and resolve this issue.Possible SolutionsA. Check
Error 678 Pada Modem
that your modem is properly connected B. Check your modem settings C. Check your dialup settings D.
Error 678 Modem Huawei
Change your access numbersE. Add three commas to your custom suffixF. Upgrade your modem drivers or enter an initialization stringA. Check that your modem is properly connected
Modem Smartfren Error 678
There are two modem outlets on the back of your computer. The correct outlet will be labeled as Line or will have a picture of a wall jack next to it. Please verify that the telephone cord is connected from the wall jack directly into the correct modem outlet.If you have other devices connected between the modem error 680 wall jack and the modem (such as fax machines, caller id boxes, or other phones), these could be interrupting the dial tone. Disconnect any devices other than the modem and try reconnecting to NetZero. If this resolves the problem, reconnect the devices to a different wall jack. B. Check your Modem settings Click the Windows Start button, point to Settings and select Control Panel. Double-click Modems and click the Properties button. Set the speed for your modem from the Maximum Speed, menu. For 14.4 modems use 19200, for 28.8 modems use 38400 and for 56k use 57600. Make sure Only connect at this speed is not checkedSelect the Connection tab. Under Call Preferences, ensure that the box marked Cancel the call if not connected within is unchecked. Some modems may not allow you to change the call preferences. Click OK then click Close to exit. Retry your NetZero connection. C. Check your Dialup settingsMake sure you have the NetZero software configured to dial yo
Ethernet & T1 Service trueSTREAM Business Standard DSL Hosted Voice Service Website Hosting SUPPORT SUPPORT modem error 691 Where are you? Support > Knowledge Base > DSL Support > modem error 676 Dynamic IP > Windows XP PPPoE Client Error 678 Windows XP PPPoE Client Error 678 Print Windows XP PPPoE Client modem error 777 Error 678Error 678 is the error code that indicates the remote computer did not respond. This error code is rather difficult to troubleshoot since there can be many things that cause this error. Follow http://www.netzero.net/support/errors/error678-871.html the instructions below to troubleshoot an error 678.1. Verify that the modem is in sync. The modems sync light (Ready/DSL/Line) should be solid green or solid amber (in the case of a broadmax modem). If the modem is not in sync refer to the check sync knowledge base heading or call into tech support to troubleshoot the problem.2. Verify that there is a solid Ethernet connection between the computer and https://www.dslextreme.com/support/kb/dsl-support/dynamic-ip/windows-xp-pppoe-client-error-678 the modem. A solid connection is indicated by a green link light (labeled link/enet/LAN). Often the link light will blink when there is Ethernet activity between the modem and the PC. If the link light is not on then unplug both ends of the cable and plug them back in, this will "reseat" the cable. If you are still unable to get a link light call into tech support at 866-491-7221 in order to receive further assistance with this issue.3. Make sure that there is no router involved. A router will cause this error every time. If you are using a router you do not need to use the windows XP PPPoE client, however you must set the router to PPPoE authentication. This is covered in the router setup knowledge base article.4. Turn the modem off for 10-15 seconds and t hen turn it back on. When the sync light (Ready/Line/DSL) is solid attempt to reconnect. If your modem does not have a power switch simply unplug the power cable.5. Ensure that the line is properly filtered. Make sure that all phone devices on the line have ADSL Micro Filters installed on them, make sure that there is no ADSL micro filter on the DSL modem.
not respond.” Broadband connections If this error occurs with a broadband connection, it could be because of the following reasons: The network cable to the machine may have been unplugged. The modem connecting to the Internet http://www.tech-faq.com/error-678.html may be disabled or its drivers may be corrupt. Spyware. The TCP/IP stack on the computer is corrupt and needs repair. A third party firewall software is erroneously preventing the user from connecting to the Internet. The options below will help users to get around this issue: Ensure that the network cable is correctly connected and that the cable is not damaged. Also ensure that the network adapter is enabled. To do this, click Start, Run and type modem error ncpa.cpl, and click OK. After right clicking the Local Area Connection icon, click ‘Enable’ if it is available. Try restarting both the computer and the modem. After rebooting, wait until all applications and services have finished loading. After that, try the connection again. If using Windows XP, use the netsh command to reset the tcp/ip interfaces. Click Start then select Run. In the box that appears, type ‘cmd’ and click the OK button. When the command window appears, error 678 modem type ‘netsh interface ip reset log.txt’ and hit the enter button. Type ‘exit’ at the command prompt and hit the enter button. Restart the computer and try again. Try reinstalling the modem and its drivers. Use a good anti-spyware tool to get rid of spyware and/or adware that may be hindering a good Internet experience. Powerful firewall programs such as ZoneAlarm can cause the Error 678 to appear during their operation. To try isolating the problem, uninstall the firewall program and test the machine. If the program is indeed causing the issue, contact its technical support for a solution. VPN Connections in Windows 2000 If using Windows 2000 and getting error 678 when opening a VPN connection, a hotfix is needed. Download the most recent service pack from Microsoft and install it. If the problem persists, contact Microsoft for support here. NOTE: Microsoft may charge for their assistance. Dial-up Systems Error 678 generally means that the line is ringing, but the remote system is not answering the call. Check the number being called and verify that the number is correct. If using an external modem, turn on the speaker to listen to the connection using the toggle switches on the modem chassis. The exact behavior will vary from modem to modem, so check the modem manufacturer’s manual. If using an internal modem that supports the Hayes modem command set, turn the mod