Error 678 Dial Up Modem
Contents |
differentOperating SystemWindows98Windows95WindowsMEWindowsNTWindows2000WindowsXPWindowsVistaWindows7Windows8Mac OS-9 Mac OS-X Linspire Common Connection Errors / SolutionsError 678: Remote modem not respondingSeveral factors can cause the 'Remote modem not responding' error. The following information should help you to identify the cause of the error and resolve modem error 680 this issue.Possible SolutionsA. Check that your modem is properly connected B. Check modem error 691 your modem settings C. Check your dialup settings D. Change your access numbersE. Add three commas to your custom modem error 676 suffixF. Upgrade your modem drivers or enter an initialization stringA. Check that your modem is properly connected There are two modem outlets on the back of your computer. The correct outlet
Modem Error 777
will be labeled as Line or will have a picture of a wall jack next to it. Please verify that the telephone cord is connected from the wall jack directly into the correct modem outlet.If you have other devices connected between the wall jack and the modem (such as fax machines, caller id boxes, or other phones), these could be interrupting the modem error 619 dial tone. Disconnect any devices other than the modem and try reconnecting to NetZero. If this resolves the problem, reconnect the devices to a different wall jack. B. Check your Modem settings Click the Windows Start button, point to Settings and select Control Panel. Double-click Modems and click the Properties button. Set the speed for your modem from the Maximum Speed, menu. For 14.4 modems use 19200, for 28.8 modems use 38400 and for 56k use 57600. Make sure Only connect at this speed is not checkedSelect the Connection tab. Under Call Preferences, ensure that the box marked Cancel the call if not connected within is unchecked. Some modems may not allow you to change the call preferences. Click OK then click Close to exit. Retry your NetZero connection. C. Check your Dialup settingsMake sure you have the NetZero software configured to dial your local access number number correctly. Some areas may require you to dial the area code plus the number even if you are dialing into the same area code. You may want to call your operator to find out the p
Ethernet & T1 Service trueSTREAM Business Standard DSL Hosted Voice Service Website Hosting SUPPORT SUPPORT Where are you? Support > Knowledge Base modem error 718 > DSL Support > Dynamic IP > Windows XP PPPoE Client Error 678 Windows XP
Modem Error 721
PPPoE Client Error 678 Print Windows XP PPPoE Client Error 678Error 678 is the error code that indicates the remote computer did not
Modem Error 633
respond. This error code is rather difficult to troubleshoot since there can be many things that cause this error. Follow the instructions below to troubleshoot an error 678.1. Verify that the modem is in sync. The modems sync light (Ready/DSL/Line) http://www.netzero.net/support/errors/error678-871.html should be solid green or solid amber (in the case of a broadmax modem). If the modem is not in sync refer to the check sync knowledge base heading or call into tech support to troubleshoot the problem.2. Verify that there is a solid Ethernet connection between the computer and the modem. A solid connection is indicated by a green link light (labeled link/enet/LAN). Often the link light will blink when there is Ethernet activity between the modem and https://www.dslextreme.com/support/kb/dsl-support/dynamic-ip/windows-xp-pppoe-client-error-678 the PC. If the link light is not on then unplug both ends of the cable and plug them back in, this will "reseat" the cable. If you are still unable to get a link light call into tech support at 866-491-7221 in order to receive further assistance with this issue.3. Make sure that there is no router involved. A router will cause this error every time. If you are using a router you do not need to use the windows XP PPPoE client, however you must set the router to PPPoE authentication. This is covered in the router setup knowledge base article.4. Turn the modem off for 10-15 seconds and t hen turn it back on. When the sync light (Ready/Line/DSL) is solid attempt to reconnect. If your modem does not have a power switch simply unplug the power cable.5. Ensure that the line is properly filtered. Make sure that all phone devices on the line have ADSL Micro Filters installed on them, make sure that there is no ADSL micro filter on the DSL modem. If all filters are correctly installed and you still receive this error the next step is to isolate the line. Do this by removing all phone devices from the line except for the DSL modem, and then attempt to reconnect.6. Are there any software firewalls enabled (Zone Alarm, Norton Internet Security, McAfee Personal Firewall)? Firewalls can cause
360 games PC games https://support.microsoft.com/en-us/kb/892889 Windows games Windows phone games Entertainment All Entertainment Movies & TV Music Business & Education Business Students & educators http://www.dell.com/support/article/us/en/19/SLN67321 Developers Sale Sale Find a store Gift cards Products Software & services Windows Office Free downloads & security Internet modem error Explorer Microsoft Edge Skype OneNote OneDrive Microsoft Health MSN Bing Microsoft Groove Microsoft Movies & TV Devices & Xbox All Microsoft devices Microsoft Surface All Windows PCs & tablets PC accessories Xbox & games Microsoft Lumia All error 678 dial Windows phones Microsoft HoloLens For business Cloud Platform Microsoft Azure Microsoft Dynamics Windows for business Office for business Skype for business Surface for business Enterprise solutions Small business solutions Find a solutions provider Volume Licensing For developers & IT pros Develop Windows apps Microsoft Azure MSDN TechNet Visual Studio For students & educators Office for students OneNote in classroom Shop PCs & tablets perfect for students Microsoft in Education Support Sign in Cart Cart Javascript is disabled Please enable javascript and refresh the page Cookies are disabled Please enable cookies and refresh the page CV: {{ getCv() }} English (United States) Terms of use Privacy & cookies Trademarks © 2016 Microsoft
How do I resolve Error 678: Remote modem not responding in Microsoft Windows XP? - KB Article - 170084 Verify the Modem is Connected ProperlyThere are two modem outlets on the back of your computer. The correct outlet is labeled Line or has a picture of a wall jack next to it. Verify the telephone cord is connected from the wall jack directly into the correct modem outlet.If you have other devices connected between the wall jack and the modem (such as fax machines, callerID boxes, or other phones), they may interrupt the dial tone. Disconnect all other devices; at a later time, connect the devices to a different wall jack.
Verify the Modem Timeout Settings Are Properly ConfiguredIf you receive this error message immediately after the modem attempts to dial, perform the following steps: Click the Start button, point to Settings, and then click Control Panel.The Control Panel window appears.Double-click the Phone and Modem Options icon.The Phone and Modem Options window appears. Phone and Modem OptionsClick the Modems tab.A list of the modems installed on your system appears. Modem ListClick to select your modem, then click the Properties button.Click the Advanced tab, and then click the Change Default Preferences button. Advanced TabUnder Call Preferences, click to deselect Disconnect a call if idle... . Default PreferencesNOTE:Some modems may not allow you to change the call preferences. Click the OK button three times, then click Close.Attempt to reconnect to the Internet service provider (ISP).Check the Modem Dialup SettingsVerify the ISP software is configured to dial your local access number.NOTE:Some locations may require that you dial the area code as part of the telephone number. For more information, contact your telephone company. For more information on configuring your ISP software dialup settings, contact your ISP. If you are trying to disable call waiting in your ISP software, verify that the correct call waiting code is used.If your tele