Determining Percent Error Physics
Contents |
Life in the Universe Labs Foundational Labs Observational Labs Advanced Labs Origins of Life in the percent error formula physics Universe Labs Introduction to Color Imaging Properties of Exoplanets General
How To Calculate Error In Physics
Astronomy Telescopes Part 1: Using the Stars Tutorials Aligning and Animating Images Coordinates in MaxIm Fits what is a good percent error Header Graphing in Maxim Image Calibration in Maxim Importing Images into MaxIm Importing Images into Rspec Measuring Magnitude in Maxim Observing with Rigel Photometry in percent error chemistry Maxim Producing Color Images Stacking Images Using SpectraSuite Software Using Tablet Applications Using the Rise and Set Calculator on Rigel Wavelength Calibration in Rspec Glossary Kepler's Third Law Significant Figures Percent Error Formula Small-Angle Formula Stellar Parallax Finder Chart Iowa Robotic Telescope Sidebar[Skip] Glossary Index Kepler's Third LawSignificant FiguresPercent Error
Percent Error Calculator
FormulaSmall-Angle FormulaStellar ParallaxFinder Chart Percent Error Formula When you calculate results that are aiming for known values, the percent error formula is useful tool for determining the precision of your calculations. The formula is given by: The experimental value is your calculated value, and the theoretical value is your known value. A percentage very close to zero means you are very close to your targeted value, which is good. It is always necessary to understand the cause of the error, such as whether it is due to the imprecision of your equipment, your own estimations, or a mistake in your experiment.Example: The 17th century Danish astronomer, Ole Rømer, observed that the periods of the satellites of Jupiter would appear to fluctuate depending on the distance of Jupiter from Earth. The further away Jupiter was, the longer the satellites would take to appear from behind the planet. In 1676, he dete
or experimental values. This calculation will help you to evaluate the relevance of your results. It is helpful to know by percent error definition what percent your experimental values differ from your lab partners' values, or to can percent error be negative some established value. In most cases, a percent error or difference of less than 10% will be acceptable.
Negative Percent Error
If your comparison shows a difference of more than 10%, there is a great likelihood that some mistake has occurred, and you should look back over your lab to find the http://astro.physics.uiowa.edu/ITU/glossary/percent-error-formula/ source of the error. These calculations are also very integral to your analysis analysis and discussion. A high percent error must be accounted for in your analysis of error, and may also indicate that the purpose of the lab has not been accomplished. Percent error: Percent error is used when you are comparing your result to a known or accepted value. http://physics.appstate.edu/undergraduate-programs/laboratory/resources/error-analysis It is the absolute value of the difference of the values divided by the accepted value, and written as a percentage. Percent difference: Percent difference is used when you are comparing your result to another experimental result. It is the absolute value of the difference of the values divided by their average, and written as a percentage. A measurement of a physical quantity is always an approximation. The uncertainty in a measurement arises, in general, from three types of errors. Systematic errors: These are errors which affect all measurements alike, and which can be traced to an imperfectly made instrument or to the personal technique and bias of the observer. These are reproducible inaccuracies that are consistently in the same direction. Systematic errors cannot be detected or reduced by increasing the number of observations, and can be reduced by applying a correction or correction factor to compensate for the effect. Random errors: These are errors for which the causes are unknown or indeterminate, but are usually small and follow the laws of chance. Random errors can be reduced by averaging over a large
as the value of p or the acceleration due to earth's gravity, g. Since these quantities have accepted or true values, we can calculate the percent error between our measurement percent error of the value and the accepted value with the formula Sometimes, we will compare the results of two measurements of the same quantity. For instance, we may use two different methods to determine determining percent error the speed of a rolling body. In this case, since there is not one accepted value for the speed of a rolling body, we will use the percent difference to determine the similarity of the measurements. This is found by dividing the absolute difference of the two measured values by their average, or Physics Lab Tutorials If you have a question or comment, send an e-mail to Lab Coordinator: Jerry Hester Copyright © 2006. Clemson University. All Rights Reserved. Photo's Courtesy Corel Draw. Last Modified on 01/27/2006 14:25:18.