Error 2140 Internal Windows Nt
ManagementDevelopment ToolsSystem AdministrationApplication Building BlocksDownloadsDocumentationContinuous Software ManagementLicensingPlatform AvailabilityAddonSoftware ERPBASIS Transformer AMISalesSales Overviewb‑commerceHow to BuyPartnership ProgramSolutionsSolutions OverviewTraining/TutorialsDemo ShowcaseDownloadsProfessional ServicesSupportSupport OverviewFAQsKnowledge BaseDiscussion ForumsTech Support PolicyEventsEvents OverviewTrainingJava Break ArchivesTechCon2015About UsBASIS OverviewContact UsThe BASIS Advantage MagazineAnnouncementsPress ReleasesManagementLegalMaps and DirectionsLogosLiterature Support Overview FAQs Knowledge Base Discussion Forums Tech Support Policy The BASIS AdvantageCurrent IssuePrevious Issues You are hereHome KB#00720-Error 2140: An internal Windows NT error occured when starting the PRO/5 NT Data Server as a service Title: Error 2140: An internal Windows NT error occured when starting the PRO/5 NT Data Server as a service Description: When attempting to start the PRO/5 Data Server service, the following error may occur: Could not start the Pro5 Data Server service Error 2140: An internal Windows NT error occured Resolution: This error can occur for a few reasons: 1) This error may occur when attempting to start the data server and specifying a port that is already in use by another service. To remedy the error, change the port specified in Conrol Panel under the Pro5 server configuration. 2) This error may occur when attempting to start the data server when logged in as a user without proper permissions. To remedy the error, log in as the administrator (or another account with sufficient privileges) and then start the Data Server. 3) If there is anything wrong with the config.bbx file for the PRO/5 Data Server. To remedy the error, check the config.bbx file for the Data Server and recreate it if needed. Minimum requirements for this config file are: setopts byte 4, bit $20$ all invalid drives DSKSYN'd the FCBS, CIBS, and STBLEN parameters can be used (and probably should be) but are not required. Last Modified: 06/08/1999 Product: PRO/5 Data Server Operating System: Windows NTOS Error: 2140 BASIS structures five components of their technology into the BBx Generations.
Copyright BASIS International Ltd. All rights reserved. Provider of BBx® Generations. Contact us.NT 4.0 Novell NetWare 5.1 symptom Error: "Windows NT Error 2140: An internal Windows NT error occurred." Some services are not fully starting when the NT Serverreboots SERVER service hangs on reboot Event Viewer shows errors on services NDS service does not start automatically NET LOGIN service does not start automatically Browser service http://www.basis.com/kb00720 starts automatically once in a while -322 - Buffer zero length System status waiting for a connection "Service is in a Stop Pending State" change Upgraded PDC and BDC from NDS for NT 2.0 to Account Management 2.1 after first server was upgraded to http://support.novell.com/docs/Tids/Solutions/10061486.html NDS 85.12a from 7.51a cause Resolve the NDSSERVER service problem andother services will start fix Removed eDirectory from the NT server and rebooted. NT server accepted authentication and other products loaded without error. document Document Title: Error: "Windows NT Error 2140: An internal Windows NT error occurred." Document ID: 10061486 Solution ID: NOVL44304 Creation Date: 02Apr2001 Modified Date: 03Dec2002 Novell Product Class:Novell eDirectory disclaimer The Origin of this information may be internal or external to Novell. Novell makes all reasonable efforts to verify this information. However, the information provided in this document is for your information only. Novell makes no explicit or implied claims to the validity of this information. Any trademarks referenced in this document are the property of their respective owners. Consult your product manuals for complete trademark information.
NT error occured If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can http://www.vbforums.com/showthread.php?260335-Error-2140-An-Internal-Windows-NT-error-occured post: click the register link above to proceed. To start viewing messages, select https://archive.realvnc.com/pipermail/vnc-list/2002-April/029689.html the forum that you want to visit from the selection below. Results 1 to 1 of 1 Thread: Error 2140: An Internal Windows NT error occured Tweet Thread Tools Show Printable Version Subscribe to this Thread… Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode Sep 8th, 2003,05:41 AM #1 whelan_bill error 2140 View Profile View Forum Posts Thread Starter Junior Member Join Date Aug 2003 Posts 28 Error 2140: An Internal Windows NT error occured Hey, I have written an NT service, but when i try to start it up i get the following error - "Error 2140: An Internal Windows NT error occured" I looked in the Event Log for more details and i got this - error 2140 internal 'The service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion.' Has anyone any ideas on how to go about fixing this problem... I have been searching around, but nothing really works.... Thanks in advance, Bill Reply With Quote Quick Navigation Visual Basic 6 and Earlier Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums Visual Basic Visual Basic .NET VB.net CodeBank Visual Basic 6 and Earlier CodeBank - Visual Basic 6 and earlier Modern Windows Experience (Metro) Office Development Mobile Development ASP, VB Script Database Development Reporting API Games and Graphics Programming Game Demos COM and ActiveX Network Programming Visual Basic FAQs Slow Chat with the Microsoft Visual Basic team .NET ASP.NET Visual Basic .NET MVC .Net C# WPF, WCF, WF Silverlight .NET Architecture and Design General General Developer Forum IoT, IoE, and Maker Forum Testers and Testing Application Testing Application Deployment Linux Development General PC VBForums Coding Contests Contest Entries Code It Better Maths Forum Other Languages Other BASIC C and C++ Java PHP XML, HTML, Javascript, Web and CSS jQuery Assembly Other Programming Langu
date ] [ thread ] [ subject ] [ author ] Hi, I installed the OpenSSH server from Networksimplicity on some of my NT servers and all went ok: I'm able now to connect to VNC listening to the 5800 and 5900 ports on the localhost interface only but I had some problems on one of my servers: it's a Compaq Proliant 3000 running NT 4 server w/ SP 6.0a I installed the Cygnus suite first (didn't know of the Networksimplicity one at that time) but since I couldn't start the SSH server I removed the Cygwin suite and installed the OpenSSH server alone. When I try to start the OpenSSH server I get the error message you may read from the Subject: I tried to search on the technet web site but the only valid reference I found complains about IIS and there's no more any IIS on that machine since I removed the NT 4 Option Pack. Any hints? TIA. -- Pierluigi De Rosa (thorin "at" durin.khazad-dum.net). << LINUX: the choice of a GNU generation >> << For my real address... ask the Balrog. >> * Sostenete la Lega per la Soppressione dei Troll * --------------------------------------------------------------------- To unsubscribe, mail majordomo "at" uk.research.att.com with the line: 'unsubscribe vnc-list' in the message BODY See also: http://www.uk.research.att.com/vnc/intouch.html --------------------------------------------------------------------- Previous message: Fw: Error Message Next message: an internal Windows NT error has occurred Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]