Canon Error 6502 Fix
Contents |
Unplug the printer. Remove the faulty Cartridge Plug in the printer and press and hold power button Keep it held down. Press Resume twice, and this should reset the fault. Solution 2: The last cartridge installed may be faulty. Install a new cartridge Solution 3: When error is error 6502 canon ip3680 indicated, turn power switch off so green light is extinguished. Hold down resume button and hold
Error 6502 Canon Ix6560
down power button so both are held down at same time When green light comes on, continue holding down power button and let resume button
Canon Printer Error 6502
go, then press resume button twice. Let power button go. Press resume button four times, power button should be released before doing this. Wait until printer settles down, if power is off, turn on. If power will not come on, remove
Error 6502 Canon Ip4700
power cord from back of printer, then wait 15 seconds before plugging back in again and turn power on. Solution 4 (thanks to Anniina for the tip !): Unplug the power cord. Remove all ink cartridges. Plug cord back in and turn the printer on. Replace all ink cartridges. Solution 4a (Thanks to Vis8): Lift the bottom part of the door (open) When the cartridge carriage comes to the center, remove all cartridges turn off the power Turn on the power After the error 6502 canon mg5410 printer initialized, the cartridge carriage will come to the center again Replace the cartridges Close door Solution 5: Sometimes a waste ink pad reset solves the problem Libellés : Canon Pixma, Error code 22 comments: prestige said... Thanks alot. this method works!!! August 25, 2009 at 1:08 AM Edward Lorence said... Tried 10 times. Orange light is still flashing, printer will not work. Canon PG-5BK/CL-8 cartridge. Error mesaages 6502. I'm dead in the water. Never happened before. Have a stock of cartridges that I can't use. March 22, 2011 at 11:09 AM Mike Oncley said... I'm in the same boat as edward April 7, 2011 at 9:21 PM LEH said... Hi Mike and Edward,Two more solutions are added above.Good luck ! April 8, 2011 at 2:24 AM Unknown said... Where is the resume button on Canon MG6250? June 10, 2012 at 8:31 AM Anonymous said... Hahahaha... solution 3 is like the "secret cheat code" to make the printer work. If only it did.... November 21, 2012 at 11:11 PM Anniina said... None of these worked for me, but this is what did:1. Unplug the power cord.2. Remove all ink cartridges.3. Plug cord back in & turn printer on. 4. Put all ink cartridges in.That worked on mine; I hope it does on yours. January 22, 2013 at 12:53 PM Nguyên Phát Lê said... Hi guy, after several try, this is my conclusion:The printer head contact is dirty, try to clean it The "ink level detector"
and did the waste tank reset thing (pressed on and resume, then resume twice, let on go, then resume four times) which didn't work.I'm now getting a 1680 error (some tanks (2 C&M) are not installed in place)and 7 oranges flashes (wrong ink tanks canon ip3600 error 6502 installed / installed in the wrong place - helpdesc.de)When I open the lid, the carriage that holds the canon ip7240 error code 6502 carts travels over to the left more than it used to, so much so, that only I can't reach K and extra K without pulling it error 6502 oracle back to the middle.Can it be fixed or is it on the way out.regardsDr Madvibe Respond to this 0 Check to see if it gives you this error message with the old cartridge. If it does not return the new one to the store http://fix-your-printer.blogspot.com/2009/03/error-code-6502-on-canon-printer.html anc exchange it for another as the new cartridge is defective. if it does however it means the mechanical sensor inside the print head has failed and the print head itself needs to be replaced. The print head is the part of the printer that puts the ink from the cartridge onto the page. Unfortunately rteplacing the print head can sometimes cost more then replacing the machine itself. by unknown on Jun 27, 2010 at 9:33pm Add comment Please sign in to comment 0 Doc,....The 1680 error code http://www.fixyourownprinter.com/posts/67632 is saying that you have put the wrong color ink carts in the wrong position. Open the cover and when the ink cart comes to the center unplug the power cord and now you can move the head into a good position. Remove all of the ink carts. Now use a "Q" tip and some how water and clean the spring wire contacts inside the carriage for each ink cart.Now clean the contacts on the front of each ink cart. Now re-install the ink carts one at a time and close the cover each time and plug in the power and turn it on. Note the error if there is any for each ink cart you install. If the ink carts are good and you put them in the correct location you should not get any errors.The 6502 is all an "ink tank position" error, so I don't know why you thought you had a waste ink error. The reset that you did may have changed the internal defaults. Most people never get the "Waste ink Reset" done correctly. Right now just concentrate on getting good ink carts and put them in the correct position. by unknown on Jun 27, 2010 at 9:38pm Add comment Please sign in to comment 0 Thanks for your replies guys. I finally managed to have a go at this and the old cart does give the same errorI tried taking all the carts out, cleaning the 4 contacts in the carriage and putting them back one by one. Up to cyan, the only error message I go
December 9, 2013 New Update - How to Solve Error Code 6502 on a Canon http://grupdownload.blogspot.com/2013/12/new-update-how-to-solve-error-code-6502.html ix6560 Canon ix6560 How to Solve Error Code 6502 on a Canon ix6560 How to Solve Error Code 6502 on a Canon ix6560 - Have you ever experienced a sudden https://forums.techguy.org/threads/error-6502-canon-pixma-mp510-printer.937503/ while printing head of printer paper is curled or has anything due to other consequences ? Incidentally, I also have experienced the same thing on the Canon ix6560 printer and consequently error 6502 the message Mistake 6502 was accompanied by a red image . Once here there rummage through calls to customer service to Canon Service Center ( but they instead bring to their service - __ - ) , I finally found some of the following steps : HOW 1 Very easy to open and close the printer ie , remove all the ink error 6502 canon tanks of the head cartridge , and then reinstall it . HOW 2 Unplug the printer power cable plugs Hold down the reset button then plug the power cable with a resume button remains on hold Press the power button while pressing the reset button , so that the two tomhol depressed all Release the reset button with still holding the power button , then press the resume button twice quickly Release the power button , then press the resume button four times Good luck , may be useful Like This Article ? You have just read an article that categorized DLoad Driver by title "New Update - How to Solve Error Code 6502 on a Canon ix6560". You can bookmark this page with a URL http://grupdownload.blogspot.nl/2013/12/new-update-how-to-solve-error-code-6502.html. You might also to read 'an : DLoad Driver Or search other Posted by Shanti Handayani at 8:08 AM Newer Post Older Post Home Popular Posts Free Epson T13 Resetter Printer Download Epson T13 Resetter Printer Download Epson T13 Resetter Printer Download - In this post I will share about the problem or reset the pri
we highly recommend that you visit our Guide for New Members. Error 6502 Canon Pixma MP510 Printer Discussion in 'Hardware' started by smell, Jul 22, 2010. Thread Status: Not open for further replies. Advertisement smell Thread Starter Joined: Jul 22, 2010 Messages: 2 Every time I change my printer cartridges on my Canon Pixma MP510 I get the error message 6502. Admittedly the cartridges are refills but they have a chip and have always worked in the past. I've tried the re-setting business of holding power button etc but I dont have a resume button so I dont know if I'm using the right button (I'm using reset). Can anyone help - printer is about to go out the window. smell, Jul 22, 2010 #1 daz1 Banned Joined: Nov 4, 2006 Messages: 2,664 http://www.ehow.com/how_5711770_reset-canon-ink-cartridge-chip.html daz1, Jul 22, 2010 #2 smell Thread Starter Joined: Jul 22, 2010 Messages: 2 Thanks Dazl. This worked. I didnt get the same menu choices as the directions but madly pressing buttons and unplugging and plugging in seemed to do the trick. smell, Jul 22, 2010 #3 This thread has been Locked and is not open to further replies. Please start a New Thread if you're having a similar issue.View our Welcome Guide to learn how to use this site. Show Ignored Content As Seen On Welcome to Tech Support Guy! Are you looking for the solution to your computer problem? Join our site today to ask your question. This site is completely free -- paid for by advertisers and donations. If you're not already familiar with forums, watch our Welcome Guide to get started. Join over 733,556 other people just like you! Loading... Similar Threads - Error 6502 Canon Crash with "MEMORY_MANAGER", Memtest86 report 1 error? DonTron, Oct 6, 2016 at 5:07 AM, in forum: Hardware Replies: 1 Views: 43 lunarlander Oct 6, 2016 at 7:56 AM Brother laser printer displays 'error state' message talbwhite, Oct 5, 2016 at 4:41 PM, in forum: Hardware Replies: 0 Views: 45 talbwhite Oct 5, 2016 at 4:41 PM Printer in Error State floydcojacket, Oct 4, 2016 at 11:06 AM, in forum: Hardware Replies: 1 Views: 59 plodr Oct 4, 2016 at 6:57 PM Error 0x800706b9 not enough resources VanNess2485, Sep 21, 2016, in forum: Hardware Replies: 1 Views: 84 VanNess2485 Sep 23, 2016 Error 0xc00000e9 KhadijahW, Sep 20, 2016, in forum: Hardware Replies: 3 Views: 116 Hamphoeby Sep 23, 2016 Thread Status: Not open for further replies. Short URL to this thread: https://techguy.org/937503 Log in with Faceboo