Haier Washing Machine Showing Error 2
Contents |
software). Reason 1. Pump filter is blocked. Solution 1. Please open and clean the pump filter. (Filter access door is on the bottom right, at floor haier washing machine error 3 level of the washing machine). Step 1.Push a flat blade screwdriver into haier washing machine error 1 the slot on the filter cover and pull it open ,do not use excessive force.(Fig 1). Step 2.Remove haier washing machine error 7 the rubber hose from its clip and stand a suitable container under it, remove the bung to drain the water (Fig 2-3) Step 3.Replace the bung and fit it back haier air conditioner e2 error code into its clip (Fig 4-5). Step 4. Unscrew the filter and rinse it under running water, replace it and close the flap(Fig 6-7-8). Caution: 1. The filter must be in place during operation, ensure it is in place after cleaning to avoid leakage. 2.Place a container under the drain pump filter, to collect any excess water that may come out of
Haier Washing Machine Reset
the drain pump when the filter is removed. Reason 2. Drain hose end is higher than 100cm above the floor level. Solution 2. Please adjust the height of drain hose to 80-100cm above the floor. Reason 3. Drain hose is blocked or twisted. Solution 3. Please check and clean the drain hose for blockage. Reason 4. Drain hose is too long, or water is back filling from waste water pipes. Solution 4. Remove any extension to the original drain hose. Ensure the highest part of the drain hose is nearest the washing machine.Check the waste water pipes in the building are clear of any obstructions and flow freely. If the error is still exist, please unplug the machine and close the water tap, then call for service. Call Customer Service Service Consumer Products EMAIL:service@haierza.co.za PHONE:+27 (11) 513 4249 Content Feedback 1. Is this content useful? * Yes No Ask a Question Please tell us why it is not useful/Satisfied: My problem was not resolved, need service Product quality or performance My question is not listed There is no ans
Load Washer / DryerHaier washing... Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Question about Haier XQG50-11 Front Load
Washing Machine Error 2 Manual
Washer / Dryer 5 Answers Haier washing machine E2 error My Haier haier washing machine error 6 washing machine keep on giving eoor E2 everytime I press start. User manual says that lid don't close haier washing machine error code e6 properly but lid is closed.I tried to open the circuit panel but i ca't find how to open certain screws. I need service manual or advice on how to http://www.haier.com/za/help_and_troubleshootings/faq/washing_machine/front_loading/question/201403/t20140313_209219.shtml replace the lid. Same problem - different machine. We have the front loader, we just installed it and we can't even use it as we are getting the E2 message. Posted by teafour2 on Sep 07, 2008 Want Answer 1 Clicking this will make more experts see the question and we will remind you when it gets answered. 5 Comments http://www.fixya.com/support/t1015801-haier_washing_machine_e2_error Flag More Print this page Share this page × Moderate Help this question get an answer Is this question mis-categorized or about a different product? Help this question get an answer by entering the correct category or product below. Did you mean? Yes No Cancel Update (+2 points) 3 more comments spainy18 Nov 01, 2008 Getting error 2 and clothes are swimming in inches of water. It appears that there is a problem with the water draining,Help!! Please :) Getting error 2 and clothes are swimming in inches of water. It appears that there is a problem with the water draining, Help!! Please :) tingtingyuhe Jan 11, 2009 Exact same problem on my machie, don't drain and keep washing until Error 2Any one help? Exact same problem on my machie, don't drain and keep washing until Error 2 Any one help? Anonymous Mar 16, 2014 When its come to spinning..Message E2 will appear n it does not work. What its mean? When its come to spinning..Message E2 will appear n it does not work. What its mean? Anonymo
help with any question. Credentials confirmed by a Fortune 500 verification firm. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Ask http://www.justanswer.com/appliance/7cv9w-haier-portable-washing-machine-gives-e2-error-message-model.html Jon Your Own Question Jon, Appliance Technician Category: Appliance Satisfied Customers: 3625 Experience: Appliance Service Technician with 10+ years experience. 60802242 Type Your Appliance Question Here... Jon is online now My Haier Portable Washing Machine gives E2 error message Model This answer was rated: ★ ★ ★ ★ ★ My Haier Portable Washing Machine gives E2 error messageModel # XXXXXIn the manual it says it means lid is not closedThe lid is closed though. So there must be some failure washing machine to get that info to the operating system.I took off the backpanel and there seems to be some sort of metal spring part/moving stick on the left hinge (or the right hinge if you look at it from the backside of the washing machine)I did not open up the top panel to see how this works exactly.There are 2 screws in the back securing the top panel and the lid, but unscrewing those does not make that part come off haier washing machine - the whole operating panel is also located in the top part so there might be some electronics and wiring there. I am afraid to just ull it off and maybe damaging wiring/electronics there.Does anyone know how to fix this or maybe simply bypass this E2 message Share this conversation Expert: Jon replied3 years ago. Jon Grella : HelloJon Grella : My name is XXXXX XXXXX I am an authorized haier service tech and I can help you today.Jon Grella : this is a common error for these machinesJon Grella : the e2 is the lid lock error. But if your lid on the top of the washer is fully closed and not hitting the lid lock switch behind the back top portion of the washer the computer control will think the lid is not fully closed and give the error. Jon Grella : if you have taken the back panel off the machine and seen the metal switch lever and it is stuck or not hitting the lid switch correctly you will need to remove the top to fix it. That is usually what needs to be done in order to fix this problem. Jon Grella : So to take the top off you have to remove four screws. Two of which are hidden and two that are not. There are the two screws that you mention in the back that are not hidden. Remove those. Jon Gr