Adaptec 29320lpe Controller Error
Contents |
log in with your existing support account. Username Password Forgot your username or password? Support Home Answers Ask a Question Your Account Account Overview Support History Account Settings Notifications "SCSI adaptec 29320lpe windows 2012 driver Controller Configuration Error 02" message appears at POST Answer ID 3922 | Published 07/18/2002 adaptec asc 29320lpe 03:30 PM | Updated 02/04/2010 07:04 AM When the Adaptec SCSI Select Utility loads, the following message appears on the screen
Adaptec Scsi 29320lpe
: SCSI Controller Configuration Error 02 This information applies to the following Operating System(s): - This information is not Operating System specific Basically, the card detected a configuration error, most likely on the SCSI
Adaptec Scsi Card 29320lpe
bus. It is possible that the termination on the SCSI bus or the cable itself might have gotten defective. For test, please try to disconnect all SCSI devices on the card. Boot the system and see if you still get the error. Most of the times, this error message will appear when connecting an HVD (High Voltage Differential) SCSI device to the Low Voltage Differential (LVD) SCSI card. Ultra160 adaptec scsi card 29320lpe compatibility SCSI cards only support the use of Low Voltage Differential (LVD) and Single-Ended (SE) devices. CAUTION! Connecting HVD devices to a non-HVD SCSI controller may damage both the device and the SCSI controller. Determine if your device(s) being attached is a HVD device. Check for any markings on the device, typically near the SCSI connector that may indicate HVD or LVD/SE. However do not trust these marking completely, double check the type of device inside the unit. Although the external case may be marked as LVD, it is still possible the internal device may still be an HVD device. The manufacuter of the device(s) should be contacted, if reviewing the documentation or visiting the manufacturers web shed light on the interface style the device is using. Note: When using a HVD (High Voltage Differential) device, a HVD SCSI card must be used. The correct Adaptec HVD SCSI product, would be an AHA-2944UW. This HVD SCSI card, designed specifically to work with HVD SCSI devices only. Was this answer helpful? Yes No Your rating has been submitted, please tell us how we can make this answer more useful. Email *Required Your Feedback *Required Answers others found helpful Controller B at slot 02, 02:0A:01 SCSI Controller C
Products Downloads Knowledgebase Register Your Product Compatibility Reports Quick Links TSID
Adaptec 29320
Importance Support Options RMA Information Contact Support adaptec 29320alp Channel Partners Contact Us HomeSupportSCSI Host AdaptersAdaptec SCSI Card 29320LPE Adaptec adaptec scsi card 29320lpe driver SCSI Card 29320LPE The Adaptec 29320LPE, PCIe x1, single-channel Ultra320 SCSI HBA is a low profile SCSI card ideal for attaching tape drives, tape libraries, magneto-optical http://ask.adaptec.com/app/answers/detail/a_id/3922/~/scsi-controller-configuration-error-02-message-appears-at-post drives, DVD libraries, JBODs, RAID Arrays and other SCSI peripherals to servers and workstations. With one external and one internal SCSI connector, support for up to 15 SCSI devices, the 29320LPE enables incredible flexibility in configuring your system. Note: Only drivers that are not included or embedded within a supported operating http://storage.microsemi.com/en-us/support/scsi/u320/asc-29320lpe/ system are listed below. To see a complete list of supported operating systems see the Product Specifications Select your operating system or software below Bios Updates and Other Downloadable Files Bios Updates and Other Downloads Linux Driver Source Linux Driver Source Code Microsoft Microsoft Windows 7 Microsoft Windows 7 x64 Microsoft Windows Server 2003 Microsoft Windows Server 2003 x64 Microsoft Windows Server 2008 Microsoft Windows Server 2008 x64 Microsoft Windows Vista Microsoft Windows Vista x64 Microsoft Windows XP Microsoft Windows XP x64 Novell NetWare Novell NetWare Downloads Red Hat Linux Red Hat Enterprise Linux 4 SuSE Linux SuSE Linux Enterprise Server 10 SuSE Linux Enterprise Server 9 Product Documentation 29320LPE Installation and User's Guide (Feb. 07) (PDF 26 MB) Release Notes 29320LPE and U320 SCSI Driver Updates Feb. 07 (PDF 32 KB) Supported Operating Systems Microsoft WindowsSuSE LinuxRed Hat LinuxNovell NetWareSCO OpenServerSCO UnixWareSun SolarisFor a detailed list see ASK Answer ID 15032 Product Documentation 29320LPE Instal
Help Receive Real-Time Help Create a Freelance Project Hire for a Full Time Job Ways to Get Help Ask a Question Ask for https://www.experts-exchange.com/questions/23446336/Troubleshooting-SCSI-card-Autoloader-DPM-2007-Tape-backup-failure.html Help Receive Real-Time Help Create a Freelance Project Hire for a Full Time Job Ways to Get Help Expand Search Submit Close Search Login Join Today Products BackProducts Gigs Live Careers Vendor Services Groups Website Testing Store Headlines Experts Exchange > Questions > Troubleshooting SCSI card - Autoloader - DPM 2007 Tape backup failure. adaptec scsi Want to Advertise Here? Solved Troubleshooting SCSI card - Autoloader - DPM 2007 Tape backup failure. Posted on 2008-05-30 Storage Storage Software Hardware 3 Verified Solutions 5 Comments 3,901 Views Last Modified: 2013-11-14 Currently running DPM 2007 with Adaptec 29320LPE SCSI card, attaching a Quantum Superloader 3. Tape backups kick off fine up adaptec scsi card to around 55 GB's, but then fail with the following error in DPM: Type: Tape backup Status: Failed Description: DPM encountered a critical error while performing an I/O operation on the tape in Drive Quantum LTO 3 Tape Drive. (ID 30101 Details: The request could not be performed because of an I/O device error (0x8007045D)) Corresponding Errors in Event Log: Event Type: Error Event Source: adpu320 Event Category: None Event ID: 15 Date: 5/30/2008 Time: 7:14:33 PM Description: The device, \Device\Scsi\adpu3201, is not ready for access yet. Event Type: Error Event Source: QLTOx32 Event Category: None Event ID: 11 Time: 7:14:33 PM Description: The driver detected a controller error on \Device\TapeDr. I understand the current autoloaders are Multi-LUN...and have configured the Adaptec as such...but to no avail. I've also applied a hotfix from Microsoft (KB946647) which corresponds to the I/O error seen in DPM...although it specifically applies to when tapes are full (which isn't the case here). Any
be down. Please try the request again. Your cache administrator is webmaster. Generated Thu, 29 Sep 2016 19:23:46 GMT by s_hv997 (squid/3.5.20)