110t Error Code
Contents |
THIS DISCUSSION Dell 115822 Followers Follow Join the Community! Creating your account only takes a few minutes. Join Now We use a Dell Powervault 100T LTO-3 drive to do our backups nightly. Today, a
Dell Powervault 114x Error Codes
job failed. I looked at the drive and the LED panel is showing a dell powervault 114t error codes big, red, ugly 3 and the light near the eject button is flashing amber, slowly. I googled to see if I powervault 110t manual could find any help, but there is information about error codes 2, 5, and 6. Anyone know anything about 3? Tags: Dell115,784 FollowersFollow Reply Subscribe RELATED TOPICS: Dell Powervault 114T LED codes Dell PowerVault 3220 Management
Dell Powervault 114x Error Code C
How much should this error concern me on a Dell Powervault Ultrium 4   4 Replies Mace OP Rockn Aug 14, 2014 at 1:32 UTC Download the ITDT tape drive diags. Should give you some idea of what is going on. ftp://ftp.software.ibm.com/storage/ITDT/Current
0 Poblano OP Hype1099 Aug 14, 2014 at 1:34 UTC From the manual off of dell's website for PowerVault 100t LTO3: Firmware problem. TheDell Powervault Error Code 7
tape drive determined that a firmware error occurred. Perform the following action: 1. Power the tape drive off and on, then retry the operation that produced the error. The error code clears when you power-off the tape drive or place it in maintenance mode. 2. If the problem persists, download the latest firmware and retry the operation. Link to Manual 0 Ghost Chili OP starg33ker Aug 14, 2014 at 1:35 UTC It sounds like your tape drive is bad. Could be as simple as a bad tape...does it clear when you take it out? 0 Sonora OP user9954 Aug 14, 2014 at 2:22 UTC Is it making a grinding noise? Tapes get jammed in these units fairly easy, take the lid off the unit, power it back on and then take a look inside and see what is happening with the unit. You might need to manually remove a tape from inside and then put the lid back on. Tapes normally get stuck in the drive rather than the magazines. 0 This discussion has been inactive for over a year. You may get a better answer to your question by starting a new discussion. Text Quote Post |Replace Attachment Add link Text to display: Where should t
LTO3 Troubleshooting Manual Page 21 User guide. Hide thumbs Also See for PowerVault 110T LTO3 Compatibility matrix - 90 pages 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 dell powervault 114x error code 8 25 26 27 28 29 30 31 32 4. To select the function, press and hold
Dell Powervault 114x Error Code 7
the eject button for 3 seconds. After you select the function, display then goes blank, and the tape drive exits maintenance mode. An illuminated dell powervault 114x manual red dot on the single-character display indicates that a drive dump has been created. You can also perform this operation when the tape drive is in normal operating mode. Simply press and hold the eject button for 10 seconds. Function https://community.spiceworks.com/topic/560904-dell-powervault-110t-error-codes Code 5 — RESERVED (Service Function) Function Code 6 — RESERVED (Service Function) Function Code 7 — RESERVED (Service Function) Function Code 8 — RESERVED (Service Function) Function Code 9 — Display Error Code Log Causes the tape drive to display the last ten error codes, one at a time (the codes are ordered; the most recent is presented first and the oldest (tenth) is presented last). To view the drive error log: 1. Make sure that no cartridge is in http://www.manualslib.com/manual/551349/Dell-Powervault-110t-Lto3.html?page=21 the drive. 2. Within a 2-second interval press the eject button three times. The status light becomes solid amber, which means that the drive is in maintenance mode. 3. Press the eject button once per second until 4. Press and hold the eject button for 3 seconds to view the most recent error code. 5. Refer to "Descriptions and Corrective 6. Press the eject button to view the next error code. (The codes are ordered; the most recent is presented first and the oldest (tenth) is presented last.) 7. Continue to press the eject button until been cleared, a will appear immediately and the drive will exit maintenance mode. A maximum of ten error codes are stored. To redisplay the error codes, repeat steps 1 through 7. Function Code A — Clear Error Code Log Causes the tape drive to erase the contents of the error code log. 1. Make sure that no cartridge is in the drive. 2. Within a 2-second interval, press the eject button three times. The status light becomes solid amber, which means that the drive is in maintenance mode. 3. Press the eject button once per second until it redisplays. 4. To select the function, press and hold the eject button for 3 seconds. After you select the function, the tape drive erases all errors from the error code log, displays , then exits maintenance mode. Function Code C — Insert Cart
110T LTO-2 Ultrium Tape DriveDell Power Vault... Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × http://www.fixya.com/support/t15360930-dell_power_vault_110t_error_code_5 Question about Dell PowerVault 110T LTO-2 Ultrium Tape Drive Open Question Dell Power Vault 110T error code 5 - Dell PowerVault 110T LTO-2 Ultrium Tape Drive Posted by Anonymous on Dec 12, 2012 Want Answer 0 Clicking this will make more experts see the question and we will remind you when it gets answered. Comment Flag More Print this page error code Share this page × Moderate Help this question get an answer Is this question mis-categorized or about a different product? Help this question get an answer by entering the correct category or product below. Did you mean? Yes No Cancel Update (+2 points) You can't post conmments that contain an email address. × Comment Anonymously Video Images 3 Suggested dell powervault 114x Answers inspector663 1 Answer SOURCE: Dell Power Vault 110T error code 6 This means that the drive was unable to determine the exact issue. See http://support.dell.com/support/edocs/stor-sys/110TLTO2/en/ug/trouble.htm for more information and other error codes Posted on Sep 14, 2009 Helpful 1 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images SirEbrum 50 Answers SOURCE: Using SDLT cleaning Tape When the drives Clean LED comes on, install a "Universal" LTO Cleaning tape, as these drives do not need routine cleaning. Only ever clean a LTO drive when it's requested, as the cleaning media itself is more abrasive than a standard tape. Posted on Jan 06, 2010 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images gfxcasa 261 Answers SOURCE: Dell power vault 110T DRIVE shoing download from here http://i2links.com/5233 :) Posted on Aug 01, 2010 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a grea