Dvd No Disc Error Message
Contents |
message referring to no disc being in the system. This can be infuriating because you can see that there is a disc, however, the CD / DVD player cannot. Every time the tray
Dvd Player Disc Error Message
closes, the laser beam fires two long bursts of laser light, and the focusing platform moves up lg dvd player disc error message and down attempting to focus the beam. This is the time when it is looking for a disc. If the laser has failed, then it
Sony Dvd Player Error Message Cannot Play This Disc
will not be able to detect a CD and therefore the error message appears. I normally do two things when this happens. I normally clean the lens just in case there is dust on it obstructing the laser path. If cleaning the wii disc error message lens does not solve the problem then I make sure the laser is working. Obviously one should never look directly into the laser unit, you would have to be plain stupid if you did that. The laser light is bright enough that one can see the diffused red light from a distance obliquely. A piece of paper the size of a standard CD within the tray can also help, because when the tray closes, one can see the diffused red light on the paper. It bose disc error message is usually bright enough and visible from the other side of the paper. If there is no red light, then the laser has failed. Back in the 1990s, I used to fix many of these and it was always either the spindle motor or the laser that failed. These two components are in constant use and wear out the most. Laser diodes do not last forever, especially on the early players manufactured in the 1980s. It would be very surprising to find a player still working from that era. Most of those units used cheap motors where the brushes wore out within a few years. Moreover, if that did not fail, then the laser surely would. The laser diode manufacturing process was not as refined either, and those diodes had a short finite life to them. Most of those early CD players would be hard to find as they often ended up in landfill. I have come across many high-end players of recent time that use the same cheap mass produced drive mechanisms. Moreover, most of those failed within a few years as well. This is a shame, as one would expect high-end players to have better components for the mechanism; however, it is usually the same cheap mechanism found in unbranded supermarket models. A laser diode, being a semiconductor, fails in an interesting way. When it is reaching the end of its useful life, and about to fail, it becomes, unstable. Its operation becomes sporadic, which can confuse the
What Do I Need to Clean a DVD Laser Lens? How to Clean the Laser Pickup Lens on your DVD Player How to Fix a Scratch on a PlayStation CD How to Unjam a CD Player How to Get an MP3 Player to Work When It Is
Dvd Error Message Wrong Region
Dead How to Fix a Philips CD Changer You've popped the popcorn, poured a glass of disk error message your favorite beverage and settled in to watch a movie, but when you press "Play" on the remote control, the dreaded "NO DISC" error appears on
Disk Error Message Windows 7
your DVD player. If you're lucky, you may be able to correct the problem by just opening and closing the disc tray on the player and trying again. If you're really unlucky, your DVD player might be defective. However, more often http://www.petervis.com/CD_and_DVD_Players/no-disc-in-cd-player-error/no-disc-in-cd-player-error.html than not, a scratched or smudged disc or a dirty laser lens in the player is usually the cause of the error, and is something you may be able to fix in a few minutes. Correcting Common Disc Problems Step 1Press the "Eject" or "Open" button on the DVD player to disc tray to determine if it opens easily and does not appear jammed or hindered. If the disc tray appears to open slower than usual or fails to open, the disc may not http://techin.oureverydaylife.com/fix-nodisc-error-dvd-player-1786.html sit flush in the tray or otherwise be seated properly. Use your hand to pull out the disc tray slowly if it does not open on its own and then reseat the disc. Close the disc tray and press "Play" on the DVD player again to see if reseating the disc in the tray corrects the "NO DISC" error. Step 2Power off the DVD player, then back on again. Attempt to play the DVD disc normally. Sometimes, an error in the DVD player firmware may prevent the device from reading discs properly. When this occurs, resetting the player often corrects "NO Disc" errors. Step 3Remove the disc from the DVD player. Use a lint-free cloth and some denatured alcohol or water to clean the disc and remove any dust or smudges that may prevent the player from reading it properly. Reinsert the disc into the player and press "Play" to see if cleaning the disc fixes the "NO DISC" error. Cleaning the DVD Laser Lens Step 1Power off the DVD player and disconnect all cables. Use your fingers to open the disc tray door slowly and gently. Alternatively, insert a pin or straightened paper clip into the small "Manual Eject" hole next to the disc tray if the unit has one. Step 2Use a can of compressed air to blow out the inner area of the DVD player exposed by opening the disc tray. Use short bursts of air from the can to clean out any dust or residue tha
steps to follow so that you can firstly identify a problem you may be having with an optical http://diyvideoeditor.com/guide-to-dvd-cd-game-disc-repair/ disc followed by some steps you can take to correct that problem. The sequence here should apply to just about any situation you have with a DVD, CD or game disc regardless of whether the disc contains just data or if it has been created to play back video. As a word of warning, some of the steps may involve treatment to the surface error message of the disc to correct reading errors and it is important to note that they may NOT be applicable to Blu-ray discs. Blu-ray discs are manufactured differently and only light polishing is suitable for them. Doing otherwise may result in permanent damage to the disc surface that may render the disc completely useless. The main difficulty in starting out is that you are most likely disc error message getting some kind of error message from the disc reader and you think that the problem is from some particular source because of that message. Common error messages such as Disc Error, No Disc, Invalid DVD Navigation or even Invalid File Structure tend to make you think you have a problem disc… not a problem reader. The reality is that these and just about all other error messages you may get are essentially meaningless and are telling you nothing. They are simply pre-written error messages that may randomly appear from within the software when ANY kind of problem occurs. They are not the result of some hidden and highly technical diagnostic process having been carried out by the software! It’s just smoke and mirrors! You can place a faulty disc into a reader and have it report that there is No Disc… which is just silly because obviously there is a disc in there! So let's get started. Is It A Disc Error or a Player Error? If you have a disc that won’t play in a particular device the first thing to do is to take the disc out and inspect t