Killdisk Error
Contents |
Questions How is the data erased? Are there any best practices for using Active@ KillDisk to erase large arrays of hard drives? What types of HDD it understands? Will I be able to use my HDD after Active@ KillDisk erase operation? Why can killdisk (or hard how to use killdisk step by step drive monitor) not return serial numbers from drives hooked up to RAID controllers? How how to use killdisk usb many operating systems supported by KillDisk? Does KillDisk run on any computer? KillDisk Application Which method is used for data access in DOS? killdisk bootable usb I get an error message that "The disk is in use or locked" when I try to WIPE a volume with KillDisk. General Questions How is the data erased? Active@ KillDisk communicates with the system killdisk cannot write to sectors board Basic Input-Output Subsystem (BIOS) functions to access hardware directly. It uses Logical Block Addressing (LBA) access if necessary to clean FAT32 drives more than 8 Gb in size. To erase data it overwrites all addressable locations on the drive with zeros (FREE version). Active@ KillDisk Professional version suggests several methods for data destruction. For example, in US DoD 5220.22-M method it overwrites all addressable storage and indexing locations on the drive three times:
Killdisk Review
with zeros (0x00), complement (0xFF) and random characters; and then verifies all writing procedures. This complies with the US DoD 5220.22-M security standard. New! Automating Erasure with Active@ KillDisk Read more Automating Erasure with Active@ KillDisk. Tips and suggestions Read more Are there any best practices for using Active@ KillDisk to erase large arrays of hard drives? Hard Drives may be erased individually in a JBOD configuration, however, it is more optimal to configure the array of disks using either a RAID0+1 or a RAID 10 configuration as depicted below. We need to completely erase all data from a raid set including the raid striping information.. What is the best way to do this? You should use a software like killdisk. The striping information is stored on sectors on the disk, and since Killdisk erases all sectors, it will erase those sectors as well. What types of HDD it understands? All types of HDD are supported. KillDisk will clean it up properly if hard disk drive or USB disk is visible in BIOS, or accessible under Windows environment (device drivers properly installed). Will I be able to use my HDD after Active@ KillDisk erase operation? To be able to use HDD again you need to: repartition HDD using a standard utility like FDISK refo
a network drive when booting up into Active@ Boot Disk for Windows? The Boot Disk Creator will not recognize the USB memory stick plugged into the system.
Killdisk Pro
I would like to create a custom bootable image that automatically includes killdisk alternative settings such as sending a certificate by email, including our logo in the certificate and other options. It seems killdisk vs dban I can do this in the installed version using the KillDisk.ini file. How can I do something similar for a CD created using Boot Disk Creator? The Active@ Boot Disk http://www.killdisk.com/killdisk-application-faq.htm bootable media is not booting up my system after I've selected the correct Boot Priority. It either sits at a blank screen or just tries to boot up from my hard drive. What can I do? How to load Active@ Boot Disk over the network via PXE environment? We are using a WinPE environment that is booted into via PXE from a http://www.killdisk.com/bootdisk-faq.htm Windows Deployment Server. I am wondering if there is a way for us to copy registry information and files into the WIM file that we boot from so the applications are already installed and registered? Or will I need to script the installation and registration to occur each time we boot into WinPE? Why does the computer reboot after 72 hours after running anything from within Boot Disk? How can I set my computer to boot from a floppy, CD-ROM or USB flash stick? New! Why won't my WMI based scripts work in Active@ Boot Disk when they run just fine in normal windows boots? Can I automatically map a network drive when booting up into Active@ Boot Disk for Windows? To map a drive, you would need to create a CMD script file and use the Windows "Net Use" command to map a drive, then add it into the scripts section of the Boot Disk Creator. Usage and Sample of the NET USE command. net use [devicename | *] [\\computername\sharename[\volume]] [password | *]] [/user:[domainname\] net use o: \\LA\Storage password /USER
standardsSystem requirementsSecurity hardwareAdvanced data recovery systemsGetting startedKillDisk installation and distributionLaunching and initial configurationNavigating how to through the applicationDisk Bay LayoutCreate a new Disk bay layoutSave and ImportFormatting and advanced features the disk bay layoutSave and ImportDisk Explorer viewDisk how to use Bays viewDisk Bays tree viewLocal Disks tree viewProperty viewsUsing KillDiskProcessing options and featuresDisk erase optionsDisk examination optionsDisk copy optionsError handlingXML reportsDisk examinationDisk erasureDisk cloningMount Disk ImageProcessing summaryReports, Certificates and LabelsErase certificateReportsErase labelsPreferencesGeneral preferencesDisk erase preferencesDisk examination preferencesCertificate preferencesError handling preferencesClone preferencesErase labels preferencesKillDisk station preferencesDisk batchesUsing disk batchesAdd disksEdit disk batch attributesAdvanced toolsFile BrowserHexadecimal ViewerSMART MonitorApplication logAppendixGlossaryErase methods File name tagsPublished 2016-08-22Your browser does not support iframes.
navigationHome Exchange News Tutorials Solutions Videos & Podcasts Books Certificates Office 365 News Tutorials Solutions Videos & Podcasts PowerShell Exchange Office 365 Outlook Tutorials Solutions Videos & Podcasts Windows News Tutorials Solutions Videos & Podcasts More… Kemp Load Balancers Cisco HP Symantec VMware SuperTekBoy In The News Search SuperTekBoy...getFATblock failed: 0x000000d2 when trying to use Active@ KillDisk July 25, 2013 By Gareth Gudger 7 Comments 0 Shares Share Tweet +1 Share RedditI ran into an issue recently while trying to secure wipe a Dell OptiPlex 755 with my favorite data destruction software, Active@ KillDisk. I was using their bootable DOS CD. The first two PCs I was wiping were Dell OptiPlex 745's and these wiped without a hitch. Then, when I tried to wipe my Dell OptiPlex 755 I kept getting this error during the initial boot. getFATblock failed: 0x000000d2 I tried burning new CDs and DVDs. Even tried the bootable USB stick. Nothing worked. Same error every time. I tried it on another OptiPlex 755 and bang; same issue. I then decided to browse around the BIOS and a thought came to me to try and switch the SATA Operation Mode to "Legacy". I did this, saved the BIOS and rebooted. And viola! KillDisk booted error free and allowed me to wipe the drive. You may not have an OptiPlex 755, but the rule here is to check the SATA operation mode. Whatever your options are, put it in the mode that sound as basic and legacy as you can get. If it's in a RAID mode, take it out. Hope this helps and happy data wiping! Click for Print FriendlyLast updated by Gareth Gudger on October 23, 2015.0 Shares Share Tweet +1 Share RedditFiled Under: Windows Solutions Get Tips from SuperTekBoy How-to articles! How-to videos! Time saving tips and tricks! We guarantee 100% privacy! Your